Journal article · 2026 · Open access

Fin-Ray soft gripper for object manipulation with multi-robot systems

Santiago Velasquez, Alejandro Toro-Ossaba, Daniel Sanin Villa, Juan David Núñez, David Rozo Osorio, Isis Bonet, Mario Góngora, Mario A. Giraldo, Juan C. Tejada

HardwareX, 27, e00806 · Published 11 July 2026 · DOI 10.1016/j.ohx.2026.e00806

Open full textCite this paper

In brief

“Fin-Ray soft gripper for object manipulation with multi-robot systems” is a 2026 journal article by Santiago Velasquez and 8 co-authors, published in HardwareX. OpenAlex counts 2 citations as of 22 November 2026, which puts it in the top 6% of works published in 2026 by citations. It is open access under a CC BY licence: the full text is free to read at HardwareX.

Citations
2
Most cited in
2026 (2)
Field-weighted impact
2.23
References
18
Authors
9

Abstract

Soft robotic grippers are attractive for cooperative object transport in multi-robot systems because they tolerate positioning errors and reduce the risk of damage to fragile items. However, many Fin-Ray effect grippers lack integrated force feedback, require empirical tuning of geometry, and are not documented as open hardware, which limits their adoption in research and teaching platforms. This work presents the design, fabrication, instrumentation, and validation of an open-source Fin-Ray soft gripper tailored for caging-based manipulation with mobile robots. The gripper combines 3D-printed TPU fingers optimized via finite element analysis, a thin-film piezo-resistive force sensor, and an STM32-based proportional controller that regulates gripping force in real time. The complete hardware stack, including mechanical models, firmware, and a Python graphical interface for monitoring and control, is released as open design files. The sensor was characterized in the range from approximately 0.1 N to 5 N. A third-order polynomial calibration yields an average accuracy of 70.8 % over this interval, with reduced accuracy at very low forces, and an average coefficient of variation of 1.10 %, which indicates highly repeatable measurements. Static closed-loop tests against a rigid object show convergence to a 0.981 N force setpoint with small steady-state error. Dynamic interaction tests confirm that the controller compensates for external perturbations by adjusting the gripper aperture. Energy measurements reveal an average current consumption near 250 mA during regulation, with peaks around 1 A when rejecting disturbances. These results indicate that the proposed gripper is suitable as a low-cost, reproducible end-effector for cooperative manipulation experiments in multi-robot systems.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Velasquez, S., Toro-Ossaba, A., Villa, D. S., Núñez, J. D., Osorio, D. R., Bonet, I., Góngora, M., Giraldo, M. A., & Tejada, J. C. (2026). Fin-Ray soft gripper for object manipulation with multi-robot systems. HardwareX, 27, e00806. https://doi.org/10.1016/j.ohx.2026.e00806

MLA 9

Velasquez, Santiago, et al. “Fin-Ray soft gripper for object manipulation with multi-robot systems.” HardwareX, vol. 27, 2026, p. e00806. https://doi.org/10.1016/j.ohx.2026.e00806.

Chicago

Velasquez, Santiago, Alejandro Toro-Ossaba, Daniel Sanin Villa, Juan David Núñez, David Rozo Osorio, Isis Bonet, Mario Góngora, Mario A. Giraldo, and Juan C. Tejada. 2026. “Fin-Ray soft gripper for object manipulation with multi-robot systems.” HardwareX 27: e00806. https://doi.org/10.1016/j.ohx.2026.e00806.

Harvard

Velasquez, S. et al. (2026) ‘Fin-Ray soft gripper for object manipulation with multi-robot systems’, HardwareX, 27, p. e00806. doi:10.1016/j.ohx.2026.e00806.

IEEE

S. Velasquez et al., “Fin-Ray soft gripper for object manipulation with multi-robot systems,” HardwareX, vol. 27, p. e00806, 2026, doi: 10.1016/j.ohx.2026.e00806.

BibTeX

@article{velasquez2026soft,
  title     = {{Fin-Ray soft gripper for object manipulation with multi-robot systems}},
  author    = {Velasquez, Santiago and Toro-Ossaba, Alejandro and Villa, Daniel Sanin and Núñez, Juan David and Osorio, David Rozo and Bonet, Isis and Góngora, Mario and Giraldo, Mario A. and Tejada, Juan C.},
  journal   = {HardwareX},
  year      = {2026},
  volume    = {27},
  pages     = {e00806},
  doi       = {10.1016/j.ohx.2026.e00806},
  url       = {https://doi.org/10.1016/j.ohx.2026.e00806}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Engineering › Biomedical Engineering › Soft Robotics and Applications

  • soft gripper
  • force feedback
  • open-source hardware
  • force sensor calibration
  • mobile robots
  • end-effector design
  • energy consumption

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Velasquez, S., Toro-Ossaba, A., Villa, D. S., Núñez, J. D., Osorio, D. R., Bonet, I., Góngora, M., Giraldo, M. A., & Tejada, J. C. (2026). Fin-Ray soft gripper for object manipulation with multi-robot systems. HardwareX, 27, e00806. https://doi.org/10.1016/j.ohx.2026.e00806

How many times has this paper been cited?

2 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at HardwareX: sign in and open the full text from this page.

Who wrote this paper?

Santiago Velasquez, Alejandro Toro-Ossaba, Daniel Sanin Villa, Juan David Núñez, David Rozo Osorio, Isis Bonet, Mario Góngora, Mario A. Giraldo, Juan C. Tejada.

What is the DOI of this paper?

10.1016/j.ohx.2026.e00806, permanently at https://doi.org/10.1016/j.ohx.2026.e00806. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.