Dissertation · 2004 · Open access
Performance assessment of coated cemented carbide tools in turning AISI 1018 steel
Louisiana State University · Published 8 April 2004 · DOI 10.31390/gradschool_theses.2856
In brief
“Performance assessment of coated cemented carbide tools in turning AISI 1018 steel” is a 2004 dissertation by Mohamad Nouilati, published in Louisiana State University. OpenAlex counts 6 citations as of 17 November 2026. It is open access: the full text is free to read at Civil War Book Review.
- Citations
- 6
- Most cited in
- 2020 (2)
- References
- 55
- Authors
- 1
Abstract
In this study, the machining performance of a series of commercially available coated tungsten based cemented carbides, with 55o diamond shape, were investigated during finish turning of AISI 1018 steel under dry conditions. The inserts tested had a coating of TiN, Al2O3, TiN/Al2O3 and TiC/Al2O3/TiN respectively. For comparison, uncoated cemented tungsten carbide was also tested under the same cutting conditions. The coated tools exhibited superior wear resistance over the uncoated tool. The TiC/Al2O3/TiN coated tool had the lowest flank wear due to the high abrasive resistance of the TiC layer. The Al2O3 coated tool showed superior wear-resistance over the TiN/Al2O3 coated tool due to the TiN coating that deteriorated the effect of the Al2O3 outer layer. The TiN coated tool showed the least wear resistance with respect to the other coated tools. Surface roughness appeared to increase with flank wear while oscillating for all the tested tools except for the TiN coated tool. The TiN coated tool produced a relatively consistent surface roughness that was not significantly affected by the flank wear under the conditions tested. The coated tools produced lower surface roughness compared to the uncoated tool, except for the TiN/Al2O3 coated tool, which produced considerably higher surface roughness. The reason for this however was the geometry of the chip breaker, rather than the coating materials, which produced longer chips that came in contact with the work piece during the machining process. The TiC/Al2O3/TiN coated tool produced the lowest surface roughness of all the tools tested.
Cite this paper
Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.
APA 7
Nouilati, M. (2004). Performance assessment of coated cemented carbide tools in turning AISI 1018 steel. Louisiana State University. https://doi.org/10.31390/gradschool_theses.2856
MLA 9
Nouilati, Mohamad. “Performance assessment of coated cemented carbide tools in turning AISI 1018 steel.” Louisiana State University, 2004. https://doi.org/10.31390/gradschool_theses.2856.
Chicago
Nouilati, Mohamad. 2004. “Performance assessment of coated cemented carbide tools in turning AISI 1018 steel.” Louisiana State University. https://doi.org/10.31390/gradschool_theses.2856.
Harvard
Nouilati, M. (2004) ‘Performance assessment of coated cemented carbide tools in turning AISI 1018 steel’, Louisiana State University. doi:10.31390/gradschool_theses.2856.
IEEE
M. Nouilati, “Performance assessment of coated cemented carbide tools in turning AISI 1018 steel,” Louisiana State University, 2004, doi: 10.31390/gradschool_theses.2856.
BibTeX
@phdthesis{nouilati2004performance,
title = {{Performance assessment of coated cemented carbide tools in turning AISI 1018 steel}},
author = {Nouilati, Mohamad},
year = {2004},
doi = {10.31390/gradschool_theses.2856},
url = {https://doi.org/10.31390/gradschool_theses.2856}
}
Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)
Citations by year
| Year | Citations | Share of the best year |
|---|---|---|
| 2013 | 1 | |
| 2014 | 1 | |
| 2019 | 1 | |
| 2020 | 2 | |
| 2021 | 1 |
Topic and keywords
Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- coated cemented carbide
- tungsten carbide tools
- AISI 1018 steel
- finish turning
- dry machining
- tool wear resistance
- flank wear
- surface roughness
Work with this paper
Most-cited papers in Engineering
- A Closed‐form Equation for Predicting the Hydraulic Conductivity of Unsaturated SoilsMartinus Th. van Genuchten · Soil Science Society of America Journal · 1980 · 28,197 citations
- An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experimentsW. C. Oliver, George M. Pharr · Journal of materials research/Pratt's guide to venture capital sources · 1992 · 27,379 citations
- Digital communicationsOwen Bishop · Routledge eBooks · 2007 · 24,890 citations
- The empirical mode decomposition and the Hilbert spectrum for nonlinear and non-stationary time series analysisNorden Eh Huang, Zhengwei Shen, Steven R. Long and 6 more · Proceedings of the Royal Society A Mathematical Physical and Engineering Sciences · 1998 · 24,008 citations
- Numerical Heat Transfer and Fluid FlowSuhas V. Patankar · CRC Press eBooks · 2018 · 23,491 citations
Questions about this paper
How do I cite this paper in APA style?
Nouilati, M. (2004). Performance assessment of coated cemented carbide tools in turning AISI 1018 steel. Louisiana State University. https://doi.org/10.31390/gradschool_theses.2856
How many times has this paper been cited?
6 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.
Is this paper free to read?
Yes. It is open access at Civil War Book Review: sign in and open the PDF from this page.
Who wrote this paper?
Mohamad Nouilati.
What is the DOI of this paper?
10.31390/gradschool_theses.2856, permanently at https://doi.org/10.31390/gradschool_theses.2856. Sign in and open it from this page.
Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.