Journal article · 2015 · Open access

Influencia de la velocidad de corte y la velocidad de avance en la integridad superficial del acero aisi 1045

M. Jacas Cabrera, Tania Rodríguez-Moliner, José Luís Lopes-Da Silveira

Ingeniería Mecánica, 18(3), 203–210 · Published 1 January 2015

Open full textCite this paper

In brief

“Influencia de la velocidad de corte y la velocidad de avance en la integridad superficial del acero aisi 1045” is a 2015 journal article by M. Jacas Cabrera and 2 co-authors, published in Ingeniería Mecánica. OpenAlex counts 10 citations as of 22 November 2026. It is open access under a CC BY-NC licence: the full text is free to read at Ingeniería Mecánica.

Citations
10
Most cited in
2020 (2)
Field-weighted impact
0.29
Authors
3

Abstract

El objetivo de esta investigación es el estudio de la influencia de la velocidad de corte y la velocidad de avance en la integridad superficial del acero AISI-1045, sometido a un proceso de torneado. Las probetas se sometieron a un tratamiento térmico de recocidos (81 HRB). En el trabajo se empleó un diseño experimental 32, con dos variables a tres niveles experimentales, para un total de nueve experimentos, los que fueron replicados. La integridad superficial fue evaluada con la medición de la rugosidad superficial, las tensiones residuales superficiales, la medición de dureza por nano–indentación y por el análisis de la de formación terciaria. Los resultados determinaron la gran influencia de la velocidad de avance en la rugosidad superficial. La medición de las tensiones residuales mostró la influencia de las variables de corte. Del análisis microestructural se observó la existencia de dos zonas de deformación determinándose que el espesor de la zona endurecida llegó a 50 µm. Palabras claves: integridad superficial, rugosidad superficial, nano-indentación; superficie deformada ____________________________________________________________________________ Abstract The aim of this research is to study the influence of cutting speed and feed rate on surface integrity of AISI-1045 subjected to a turning process. The specimens were in annealed condition (81 HRB). A 32 factorial experiment design was employed using low, medium and high levels of the two variables in study, performing 9 experiments with a replica. The surfaces were evaluated through the measurements of surface roughness, surface residual stresses, nano-indentation hardness and analyzing the deformed layer. Results corroborated the great influence of feed rate on surface roughness. The results of the residual stresses have shown the influence of cutting speed as well as feed rate in the behavior of circumferential and axial stress respectively. From the analysis of the microstructure was feasible to observe the tertiary deformation zone due to the machining process. The hardness measured by nano-indentation showed that the thickness of this hardened zone can reach up to 50 µm. Key words: superficial integrity, surface roughness, nano-indentation, surface deformation.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Cabrera, M. J., Rodríguez-Moliner, T., & Silveira, J. L. L.-D. (2015). Influencia de la velocidad de corte y la velocidad de avance en la integridad superficial del acero aisi 1045. Ingeniería Mecánica, 18(3), 203–210. http://ingenieriamecanica.cujae.edu.cu/index.php/revistaim/article/view/527/0

MLA 9

Cabrera, M. Jacas, et al. “Influencia de la velocidad de corte y la velocidad de avance en la integridad superficial del acero aisi 1045.” Ingeniería Mecánica, vol. 18, no. 3, 2015, pp. 203–210. http://ingenieriamecanica.cujae.edu.cu/index.php/revistaim/article/view/527/0.

Chicago

Cabrera, M. Jacas, Tania Rodríguez-Moliner, and José Luís Lopes-Da Silveira. 2015. “Influencia de la velocidad de corte y la velocidad de avance en la integridad superficial del acero aisi 1045.” Ingeniería Mecánica 18 (3): 203–210. http://ingenieriamecanica.cujae.edu.cu/index.php/revistaim/article/view/527/0.

Harvard

Cabrera, M. J., Rodríguez-Moliner, T. and Silveira, J. L. L.-D. (2015) ‘Influencia de la velocidad de corte y la velocidad de avance en la integridad superficial del acero aisi 1045’, Ingeniería Mecánica, 18(3), pp. 203–210. Available at: http://ingenieriamecanica.cujae.edu.cu/index.php/revistaim/article/view/527/0.

IEEE

M. J. Cabrera, T. Rodríguez-Moliner, and J. L. L.-D. Silveira, “Influencia de la velocidad de corte y la velocidad de avance en la integridad superficial del acero aisi 1045,” Ingeniería Mecánica, vol. 18, no. 3, pp. 203–210, 2015.

BibTeX

@article{cabrera2015influencia,
  title     = {{Influencia de la velocidad de corte y la velocidad de avance en la integridad superficial del acero aisi 1045}},
  author    = {Cabrera, M. Jacas and Rodríguez-Moliner, Tania and Silveira, José Luís Lopes-Da},
  journal   = {Ingeniería Mecánica},
  year      = {2015},
  volume    = {18},
  number    = {3},
  pages     = {203--210},
  url       = {http://ingenieriamecanica.cujae.edu.cu/index.php/revistaim/article/view/527/0}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
201811
201911
202022
202111
202211
202311
202522
202611

Its field-weighted citation impact is 0.29: it has been cited 0.29 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization

  • AISI 1045 steel
  • surface integrity
  • cutting speed
  • feed rate
  • turning
  • surface roughness
  • residual stress
  • nanohardness

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Cabrera, M. J., Rodríguez-Moliner, T., & Silveira, J. L. L.-D. (2015). Influencia de la velocidad de corte y la velocidad de avance en la integridad superficial del acero aisi 1045. Ingeniería Mecánica, 18(3), 203–210. http://ingenieriamecanica.cujae.edu.cu/index.php/revistaim/article/view/527/0

How many times has this paper been cited?

10 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Ingeniería Mecánica: sign in and open the full text from this page.

Who wrote this paper?

M. Jacas Cabrera, Tania Rodríguez-Moliner, José Luís Lopes-Da Silveira.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.