Journal article · 2018 · Open access

Determination of the Elasticity Modulus of 3D-Printed Octet-Truss Structures for Use in Porous Prosthesis Implants

Ali Bagheri, Irene Buj-Corral, Miquel Ferrer, Maria Magdalena Pastor, Francesc Roure Fernandez

Materials, 11(12), 2420 · Published 29 November 2018 · DOI 10.3390/ma11122420

Open PDFView at the publisherCite this paper

In brief

“Determination of the Elasticity Modulus of 3D-Printed Octet-Truss Structures for Use in Porous Prosthesis Implants” is a 2018 journal article by Ali Bagheri and 4 co-authors, published in Materials. OpenAlex counts 46 citations as of 22 November 2026. It is open access under a CC BY licence: the full text is free to read at Materials.

Citations
46
Most cited in
2020 (8)
Field-weighted impact
3.28
References
52
Authors
5

Abstract

In tissue engineering, scaffolds can be obtained by means of 3D printing. Different structures are used in order to reduce the stiffness of the solid material. The present article analyzes the mechanical behavior of octet-truss microstructures. Three different octet structures with strut radii of 0.4, 0.5, and 0.6 mm were studied. The theoretical relative densities corresponding to these structures were 34.7%, 48.3%, and 61.8%, respectively. Two different values for the ratio of height (H) to width (W) were considered, H/W = 2 and H/W = 4. Several specimens of each structure were printed, which had the shape of a square base prism. Compression tests were performed and the elasticity modulus (E) of the octet-truss lattice-structured material was determined, both, experimentally and by means of Finite Element Methods (FEM). The greater the strut radius, the higher the modulus of elasticity and the compressive strength. Better agreement was found between the experimental and the simulated modulus of elasticity results for H/W = 4 than for H/W = 2. The octet-truss lattice can be considered to be a promising structure for printing in the field of tissue engineering.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Bagheri, A., Buj-Corral, I., Ferrer, M., Pastor, M. M., & Fernandez, F. R. (2018). Determination of the Elasticity Modulus of 3D-Printed Octet-Truss Structures for Use in Porous Prosthesis Implants. Materials, 11(12), 2420. https://doi.org/10.3390/ma11122420

MLA 9

Bagheri, Ali, et al. “Determination of the Elasticity Modulus of 3D-Printed Octet-Truss Structures for Use in Porous Prosthesis Implants.” Materials, vol. 11, no. 12, 2018, p. 2420. https://doi.org/10.3390/ma11122420.

Chicago

Bagheri, Ali, Irene Buj-Corral, Miquel Ferrer, Maria Magdalena Pastor, and Francesc Roure Fernandez. 2018. “Determination of the Elasticity Modulus of 3D-Printed Octet-Truss Structures for Use in Porous Prosthesis Implants.” Materials 11 (12): 2420. https://doi.org/10.3390/ma11122420.

Harvard

Bagheri, A. et al. (2018) ‘Determination of the Elasticity Modulus of 3D-Printed Octet-Truss Structures for Use in Porous Prosthesis Implants’, Materials, 11(12), p. 2420. doi:10.3390/ma11122420.

IEEE

A. Bagheri, I. Buj-Corral, M. Ferrer, M. M. Pastor, and F. R. Fernandez, “Determination of the Elasticity Modulus of 3D-Printed Octet-Truss Structures for Use in Porous Prosthesis Implants,” Materials, vol. 11, no. 12, p. 2420, 2018, doi: 10.3390/ma11122420.

BibTeX

@article{bagheri2018determination,
  title     = {{Determination of the Elasticity Modulus of 3D-Printed Octet-Truss Structures for Use in Porous Prosthesis Implants}},
  author    = {Bagheri, Ali and Buj-Corral, Irene and Ferrer, Miquel and Pastor, Maria Magdalena and Fernandez, Francesc Roure},
  journal   = {Materials},
  year      = {2018},
  volume    = {11},
  number    = {12},
  pages     = {2420},
  doi       = {10.3390/ma11122420},
  url       = {https://doi.org/10.3390/ma11122420}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
201811
201966
202088
202177
202277
202333
202444
202555
202655

Its field-weighted citation impact is 3.28: it has been cited 3.28 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Cellular and Composite Structures

  • octet-truss lattice
  • 3D-printed scaffolds
  • porous implants
  • elastic modulus
  • compressive strength
  • relative density
  • tissue engineering scaffolds
  • finite element analysis

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Bagheri, A., Buj-Corral, I., Ferrer, M., Pastor, M. M., & Fernandez, F. R. (2018). Determination of the Elasticity Modulus of 3D-Printed Octet-Truss Structures for Use in Porous Prosthesis Implants. Materials, 11(12), 2420. https://doi.org/10.3390/ma11122420

How many times has this paper been cited?

46 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Materials: sign in and open the PDF from this page.

Who wrote this paper?

Ali Bagheri, Irene Buj-Corral, Miquel Ferrer, Maria Magdalena Pastor, Francesc Roure Fernandez.

What is the DOI of this paper?

10.3390/ma11122420, permanently at https://doi.org/10.3390/ma11122420. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.