Journal article · 2018 · Open access

3D Printed lattice microstructures to mimic soft biological materials

Luke Johnson, Chris A. Richburg, Madelyn Lew, William R. Ledoux, Patrick M. Aubin, Eric Rombokas

Bioinspiration & Biomimetics, 14(1), 016001 · Published 2 November 2018 · DOI 10.1088/1748-3190/aae10a

Open PDFView at the publisherCite this paper

In brief

“3D Printed lattice microstructures to mimic soft biological materials” is a 2018 journal article by Luke Johnson and 5 co-authors, published in Bioinspiration & Biomimetics. OpenAlex counts 23 citations as of 22 November 2026. It is open access: the full text is free to read at Bioinspiration & Biomimetics.

Citations
23
Most cited in
2026 (6)
Field-weighted impact
0.25
References
27
Authors
6

Abstract

OBJECTIVE: Our group has developed a method for 3D printing mechanically-realistic soft tissue, as a building block towards developing anatomically realistic 3D-printed biomechanical testbed models. METHODS: A Polyjet 3D printer was used to print lattice microstructures, which were tested in compression to evaluate the elastic profile. Lattice properties including element diameter, element spacing (ES), element cross-sectional geometry, element arrangement, and lattice rotation were varied to determine their effect on the stress-strain curve. As a case study, a single 3D printed sample was tuned such that its elastic profile matched plantar fat. RESULTS: Element diameter and ES had the largest effect on the stress-strain profile, and rotating the lattice microstructure tends to linearize the curves. A simple cubic lattice microstructure of cylindrical elements, with 0.5 mm diameter columns and 1.2 mm spacing had a stress-strain curve the was closest to plantar fat. The elastic modulus at 10, 30, and 50% strain was 7.55, 9.50, and 252 kPa respectively. Physiologic plantar fat at the same strain values has moduli values of 1.08, 7.13, and 188 kPa. SIGNIFICANCE: We demonstrated that lattice microstructures can decrease the young's modulus of soft 3D printed materials by three orders of magnitude. By creating a method for fine-tuning the elastic profile of 3D-printed materials to behave like human soft tissue, we provide an attractive alternative to more exotic and time-consuming techniques such as molding and casting.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Johnson, L., Richburg, C. A., Lew, M., Ledoux, W. R., Aubin, P. M., & Rombokas, E. (2018). 3D Printed lattice microstructures to mimic soft biological materials. Bioinspiration & Biomimetics, 14(1), 016001. https://doi.org/10.1088/1748-3190/aae10a

MLA 9

Johnson, Luke, et al. “3D Printed lattice microstructures to mimic soft biological materials.” Bioinspiration & Biomimetics, vol. 14, no. 1, 2018, p. 016001. https://doi.org/10.1088/1748-3190/aae10a.

Chicago

Johnson, Luke, Chris A. Richburg, Madelyn Lew, William R. Ledoux, Patrick M. Aubin, and Eric Rombokas. 2018. “3D Printed lattice microstructures to mimic soft biological materials.” Bioinspiration & Biomimetics 14 (1): 016001. https://doi.org/10.1088/1748-3190/aae10a.

Harvard

Johnson, L. et al. (2018) ‘3D Printed lattice microstructures to mimic soft biological materials’, Bioinspiration & Biomimetics, 14(1), p. 016001. doi:10.1088/1748-3190/aae10a.

IEEE

L. Johnson, C. A. Richburg, M. Lew, W. R. Ledoux, P. M. Aubin, and E. Rombokas, “3D Printed lattice microstructures to mimic soft biological materials,” Bioinspiration & Biomimetics, vol. 14, no. 1, p. 016001, 2018, doi: 10.1088/1748-3190/aae10a.

BibTeX

@article{johnson2018printed,
  title     = {{3D Printed lattice microstructures to mimic soft biological materials}},
  author    = {Johnson, Luke and Richburg, Chris A. and Lew, Madelyn and Ledoux, William R. and Aubin, Patrick M. and Rombokas, Eric},
  journal   = {Bioinspiration \& Biomimetics},
  year      = {2018},
  volume    = {14},
  number    = {1},
  pages     = {016001},
  doi       = {10.1088/1748-3190/aae10a},
  url       = {https://doi.org/10.1088/1748-3190/aae10a}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
201811
202011
202111
202255
202322
202433
202544
202666

Its field-weighted citation impact is 0.25: it has been cited 0.25 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Biomedical Engineering › 3D Printing in Biomedical Research

  • lattice microstructure
  • stress-strain behavior
  • elastic modulus
  • element spacing
  • lattice rotation
  • cubic lattice
  • soft tissue mechanics
  • polyjet printing

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Johnson, L., Richburg, C. A., Lew, M., Ledoux, W. R., Aubin, P. M., & Rombokas, E. (2018). 3D Printed lattice microstructures to mimic soft biological materials. Bioinspiration & Biomimetics, 14(1), 016001. https://doi.org/10.1088/1748-3190/aae10a

How many times has this paper been cited?

23 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Bioinspiration & Biomimetics: sign in and open the PDF from this page.

Who wrote this paper?

Luke Johnson, Chris A. Richburg, Madelyn Lew, William R. Ledoux, Patrick M. Aubin, Eric Rombokas.

What is the DOI of this paper?

10.1088/1748-3190/aae10a, permanently at https://doi.org/10.1088/1748-3190/aae10a. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.