Paper · 2013 · Open access

Wear Behavior of Ti(N,C)-Al2O3 Coated Cemented Carbide Tools during Milling Ti2AlNb-Based Alloy

Xiao Di Ma, Jiu Hua Xu, Wen Feng Ding, Dong Sheng Lv, Yu Can Fu

Key engineering materials, 589-590, 361–365 · Published 1 October 2013 · DOI 10.4028/www.scientific.net/kem.589-590.361

Open full textCite this paper

In brief

“Wear Behavior of Ti(N,C)-Al2O3 Coated Cemented Carbide Tools during Milling Ti2AlNb-Based Alloy” is a 2013 paper by Xiao Di Ma and 4 co-authors, published in Key engineering materials. OpenAlex counts 7 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at Key engineering materials.

Citations
7
Most cited in
2022 (2)
Field-weighted impact
0.47
References
7
Authors
5

Abstract

Ti2AlNb-based alloy is regarded as lightweight high-temperature structural material, which is expected to replace the nickel-base super alloy due to its low density, high elastic modulus, strength retention at elevated temperature, outstanding oxide resistance. However, these excellent properties also make Ti2AlNb to be difficult-to-cut material. In this paper, the milling experiment of Ti2AlNb alloy was carried out using Ti(N,C)-Al2O3 coated cemented carbide tools. SEM and EDS analysis was utilized to observe the worn tools to determine the tool failure modes and wear mechanisms. Tool life when milling Ti2AlNb was short and heavily dependent on the cutting parameters. During milling, coating material of the tool was separated rapidly from the base material. When the cutting speed exceeded 100m/min, serious cracks appeared on the tool surface. Thermal fatigue, adhesive and attrition were the predominant wear mechanisms of the coated tools.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Di Ma, X., Xu, J. H., Ding, W. F., Lv, D. S., & Fu, Y. C. (2013). Wear Behavior of Ti(N,C)-Al2O3 Coated Cemented Carbide Tools during Milling Ti2AlNb-Based Alloy. Key engineering materials, 589-590, 361–365. https://doi.org/10.4028/www.scientific.net/kem.589-590.361

MLA 9

Di Ma, Xiao, et al. “Wear Behavior of Ti(N,C)-Al2O3 Coated Cemented Carbide Tools during Milling Ti2AlNb-Based Alloy.” Key engineering materials, vol. 589-590, 2013, pp. 361–365. https://doi.org/10.4028/www.scientific.net/kem.589-590.361.

Chicago

Di Ma, Xiao, Jiu Hua Xu, Wen Feng Ding, Dong Sheng Lv, and Yu Can Fu. 2013. “Wear Behavior of Ti(N,C)-Al2O3 Coated Cemented Carbide Tools during Milling Ti2AlNb-Based Alloy.” Key engineering materials 589-590: 361–365. https://doi.org/10.4028/www.scientific.net/kem.589-590.361.

Harvard

Di Ma, X. et al. (2013) ‘Wear Behavior of Ti(N,C)-Al2O3 Coated Cemented Carbide Tools during Milling Ti2AlNb-Based Alloy’, Key engineering materials, 589-590, pp. 361–365. doi:10.4028/www.scientific.net/kem.589-590.361.

IEEE

X. Di Ma, J. H. Xu, W. F. Ding, D. S. Lv, and Y. C. Fu, “Wear Behavior of Ti(N,C)-Al2O3 Coated Cemented Carbide Tools during Milling Ti2AlNb-Based Alloy,” Key engineering materials, vol. 589-590, pp. 361–365, 2013, doi: 10.4028/www.scientific.net/kem.589-590.361.

BibTeX

@article{dima2013wear,
  title     = {{Wear Behavior of Ti(N,C)-Al2O3 Coated Cemented Carbide Tools during Milling Ti2AlNb-Based Alloy}},
  author    = {Di Ma, Xiao and Xu, Jiu Hua and Ding, Wen Feng and Lv, Dong Sheng and Fu, Yu Can},
  journal   = {Key engineering materials},
  year      = {2013},
  volume    = {589-590},
  pages     = {361--365},
  doi       = {10.4028/www.scientific.net/kem.589-590.361},
  url       = {https://doi.org/10.4028/www.scientific.net/kem.589-590.361}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
201511
201711
202222
202322
202611

Its field-weighted citation impact is 0.47: it has been cited 0.47 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization

  • Ti2AlNb alloy
  • tool wear mechanisms
  • milling
  • tool failure modes
  • coating delamination
  • thermal fatigue
  • adhesive wear
  • attrition

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Di Ma, X., Xu, J. H., Ding, W. F., Lv, D. S., & Fu, Y. C. (2013). Wear Behavior of Ti(N,C)-Al2O3 Coated Cemented Carbide Tools during Milling Ti2AlNb-Based Alloy. Key engineering materials, 589-590, 361–365. https://doi.org/10.4028/www.scientific.net/kem.589-590.361

How many times has this paper been cited?

7 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Key engineering materials: sign in and open the full text from this page.

Who wrote this paper?

Xiao Di Ma, Jiu Hua Xu, Wen Feng Ding, Dong Sheng Lv, Yu Can Fu.

What is the DOI of this paper?

10.4028/www.scientific.net/kem.589-590.361, permanently at https://doi.org/10.4028/www.scientific.net/kem.589-590.361. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.