Journal article · 2014 · Open access

Tribological Characteristics of Tetrahedral (ta-C) DLC Coating in the Presence of Commercial Lubricating Oil

K.A.H. Al Mahmud, M.A. Kalam, Mohd Faizul Mohd Sabri, Haji Hassan Masjuki, M.M. Rashed

Applied Mechanics and Materials, 679, 25–29 · Published 8 October 2014 · DOI 10.4028/www.scientific.net/amm.679.25

Open full textCite this paper

In brief

“Tribological Characteristics of Tetrahedral (ta-C) DLC Coating in the Presence of Commercial Lubricating Oil” is a 2014 journal article by K.A.H. Al Mahmud and 4 co-authors, published in Applied Mechanics and Materials. OpenAlex counts 0 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at Applied Mechanics and Materials.

Citations
0
References
9
Authors
5

Abstract

Currently, the application of diamond-like carbon (DLC) coatings for automotive components is becoming a favorable strategy to cope with the new challenges faced by the automotive industry. DLC coatings can effectively lower the coefficient of friction (CoF) and wear rate of engine components, consequently improving the fuel efficiency and durability of these components. Commercially available fully formulated lubricating oils enhance the lubrication of ferrous materials. Therefore, the interaction between nonferrous coatings (e.g., DLC) and commercial lubricating oil must be investigated. A ball-on-plate tribotester was used to run the experiments using stainless steel plates coated with tetrahedral DLC (ta-C) sliding against a 440C stainless steel ball. Wear track was investigated by scanning electron microscopy and atomic force microscopy. Energy dispersive spectroscopy was used to analyze the tribofilms inside the wear track. Raman analysis was performed to investigate the structural change of the coatings. At high temperatures, the CoF decreases but the wear rate increases in the ta-C DLC-coated plates. CoF and wear rate (coated layer and counter surface) are mostly influenced by coating graphitization.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Al Mahmud, K., Kalam, M., Sabri, M. F. M., Masjuki, H. H., & Rashed, M. (2014). Tribological Characteristics of Tetrahedral (ta-C) DLC Coating in the Presence of Commercial Lubricating Oil. Applied Mechanics and Materials, 679, 25–29. https://doi.org/10.4028/www.scientific.net/amm.679.25

MLA 9

Al Mahmud, K.A.H., et al. “Tribological Characteristics of Tetrahedral (ta-C) DLC Coating in the Presence of Commercial Lubricating Oil.” Applied Mechanics and Materials, vol. 679, 2014, pp. 25–29. https://doi.org/10.4028/www.scientific.net/amm.679.25.

Chicago

Al Mahmud, K.A.H., M.A. Kalam, Mohd Faizul Mohd Sabri, Haji Hassan Masjuki, and M.M. Rashed. 2014. “Tribological Characteristics of Tetrahedral (ta-C) DLC Coating in the Presence of Commercial Lubricating Oil.” Applied Mechanics and Materials 679: 25–29. https://doi.org/10.4028/www.scientific.net/amm.679.25.

Harvard

Al Mahmud, K. et al. (2014) ‘Tribological Characteristics of Tetrahedral (ta-C) DLC Coating in the Presence of Commercial Lubricating Oil’, Applied Mechanics and Materials, 679, pp. 25–29. doi:10.4028/www.scientific.net/amm.679.25.

IEEE

K. Al Mahmud, M. Kalam, M. F. M. Sabri, H. H. Masjuki, and M. Rashed, “Tribological Characteristics of Tetrahedral (ta-C) DLC Coating in the Presence of Commercial Lubricating Oil,” Applied Mechanics and Materials, vol. 679, pp. 25–29, 2014, doi: 10.4028/www.scientific.net/amm.679.25.

BibTeX

@article{almahmud2014tribological,
  title     = {{Tribological Characteristics of Tetrahedral (ta-C) DLC Coating in the Presence of Commercial Lubricating Oil}},
  author    = {Al Mahmud, K.A.H. and Kalam, M.A. and Sabri, Mohd Faizul Mohd and Masjuki, Haji Hassan and Rashed, M.M.},
  journal   = {Applied Mechanics and Materials},
  year      = {2014},
  volume    = {679},
  pages     = {25--29},
  doi       = {10.4028/www.scientific.net/amm.679.25},
  url       = {https://doi.org/10.4028/www.scientific.net/amm.679.25}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Lubricants and Their Additives

  • tetrahedral amorphous carbon
  • diamond-like carbon films
  • tribology
  • friction coefficient
  • wear rate
  • tribofilm
  • 440C stainless steel
  • automotive engine components

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Al Mahmud, K., Kalam, M., Sabri, M. F. M., Masjuki, H. H., & Rashed, M. (2014). Tribological Characteristics of Tetrahedral (ta-C) DLC Coating in the Presence of Commercial Lubricating Oil. Applied Mechanics and Materials, 679, 25–29. https://doi.org/10.4028/www.scientific.net/amm.679.25

How many times has this paper been cited?

0 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Applied Mechanics and Materials: sign in and open the full text from this page.

Who wrote this paper?

K.A.H. Al Mahmud, M.A. Kalam, Mohd Faizul Mohd Sabri, Haji Hassan Masjuki, M.M. Rashed.

What is the DOI of this paper?

10.4028/www.scientific.net/amm.679.25, permanently at https://doi.org/10.4028/www.scientific.net/amm.679.25. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.