Journal article · 2012 · Open access

Tool Wear Performance of TiAlN/AlCrN Multilayer Coated Carbide Tool in Machining of AISI D2 Hardened Steel

Nur Akmal Hakim Jasni, Mohd Amri Lajis, Kamaruddin Kamdani

Advanced materials research, 488-489, 462–467 · Published 15 March 2012 · DOI 10.4028/www.scientific.net/amr.488-489.462

Open full textCite this paper

In brief

“Tool Wear Performance of TiAlN/AlCrN Multilayer Coated Carbide Tool in Machining of AISI D2 Hardened Steel” is a 2012 journal article by Nur Akmal Hakim Jasni and 2 co-authors, published in Advanced materials research. OpenAlex counts 9 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at Advanced materials research.

Citations
9
Most cited in
2023 (3)
References
13
Authors
3

Abstract

This paper presents the results of experimental investigation conducted on a vertical machining centre (VMC) to ascertain the effectiveness of TiAlN/AlCrN multilayer coated carbide inserts in end milling of AISI D2 hardened steel (58-62 HRC) In high-speed dry hard milling, different cutting speed (v) and radial depth of cut (dr) were applied. Tool failure modes and wear mechanisms were examined at various cutting parameters. Flank wear, chipping and breakage at cutting edge were found to be the predominant tool failure for the cutting tools. Built-up edge, adhesion and abrasive are the wear mechanisms observed on the cutting tools. The highest volume of material removed, VMR attained was 1500 mm3, meanwhile the highest tool life (T) was 4.97 min. The surface roughness, Ra values from 0.20 to 0.45 μm can be attained in the workpiece with a high volume material removed. The relationship of tool wear performance and surface integrity was established to lead an optimum parameter in order to have high volume material removed, maximum tool life as well as acceptable surface finish.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Jasni, N. A. H., Lajis, M. A., & Kamdani, K. (2012). Tool Wear Performance of TiAlN/AlCrN Multilayer Coated Carbide Tool in Machining of AISI D2 Hardened Steel. Advanced materials research, 488-489, 462–467. https://doi.org/10.4028/www.scientific.net/amr.488-489.462

MLA 9

Jasni, Nur Akmal Hakim, et al. “Tool Wear Performance of TiAlN/AlCrN Multilayer Coated Carbide Tool in Machining of AISI D2 Hardened Steel.” Advanced materials research, vol. 488-489, 2012, pp. 462–467. https://doi.org/10.4028/www.scientific.net/amr.488-489.462.

Chicago

Jasni, Nur Akmal Hakim, Mohd Amri Lajis, and Kamaruddin Kamdani. 2012. “Tool Wear Performance of TiAlN/AlCrN Multilayer Coated Carbide Tool in Machining of AISI D2 Hardened Steel.” Advanced materials research 488-489: 462–467. https://doi.org/10.4028/www.scientific.net/amr.488-489.462.

Harvard

Jasni, N. A. H., Lajis, M. A. and Kamdani, K. (2012) ‘Tool Wear Performance of TiAlN/AlCrN Multilayer Coated Carbide Tool in Machining of AISI D2 Hardened Steel’, Advanced materials research, 488-489, pp. 462–467. doi:10.4028/www.scientific.net/amr.488-489.462.

IEEE

N. A. H. Jasni, M. A. Lajis, and K. Kamdani, “Tool Wear Performance of TiAlN/AlCrN Multilayer Coated Carbide Tool in Machining of AISI D2 Hardened Steel,” Advanced materials research, vol. 488-489, pp. 462–467, 2012, doi: 10.4028/www.scientific.net/amr.488-489.462.

BibTeX

@article{jasni2012tool,
  title     = {{Tool Wear Performance of TiAlN/AlCrN Multilayer Coated Carbide Tool in Machining of AISI D2 Hardened Steel}},
  author    = {Jasni, Nur Akmal Hakim and Lajis, Mohd Amri and Kamdani, Kamaruddin},
  journal   = {Advanced materials research},
  year      = {2012},
  volume    = {488-489},
  pages     = {462--467},
  doi       = {10.4028/www.scientific.net/amr.488-489.462},
  url       = {https://doi.org/10.4028/www.scientific.net/amr.488-489.462}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
201911
202011
202222
202333
202411
202511

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization

  • coated carbide inserts
  • end milling
  • tool wear mechanisms
  • flank wear
  • built-up edge
  • adhesion
  • abrasive wear
  • tool life

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Jasni, N. A. H., Lajis, M. A., & Kamdani, K. (2012). Tool Wear Performance of TiAlN/AlCrN Multilayer Coated Carbide Tool in Machining of AISI D2 Hardened Steel. Advanced materials research, 488-489, 462–467. https://doi.org/10.4028/www.scientific.net/amr.488-489.462

How many times has this paper been cited?

9 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Advanced materials research: sign in and open the full text from this page.

Who wrote this paper?

Nur Akmal Hakim Jasni, Mohd Amri Lajis, Kamaruddin Kamdani.

What is the DOI of this paper?

10.4028/www.scientific.net/amr.488-489.462, permanently at https://doi.org/10.4028/www.scientific.net/amr.488-489.462. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.