Paper · 2012 · Open access
Tool Wear Of Titanium/Tungsten/Silicon/Aluminum-Based-Coated End Mill Cutters In Millin Hardened Steel
Zenodo (CERN European Organization for Nuclear Research) · Published 29 September 2012 · DOI 10.5281/zenodo.1328655
In brief
“Tool Wear Of Titanium/Tungsten/Silicon/Aluminum-Based-Coated End Mill Cutters In Millin Hardened Steel” is a 2012 paper by Tadahiro Wada and Koji Iwamoto, published in Zenodo (CERN European Organization for Nuclear Research). OpenAlex counts 1 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at Zenodo (CERN European Organization for Nuclear Research).
- Citations
- 1
- Most cited in
- 2014 (1)
- Field-weighted impact
- 0.48
- Authors
- 2
Abstract
In turning hardened steel, polycrystalline cubic boron nitride (cBN) compacts are widely used, due to their higher hardness and higher thermal conductivity. However, in milling hardened steel, fracture of cBN cutting tools readily occurs because they have poor fracture toughness. Therefore, coated cemented carbide tools, which have good fracture toughness and wear resistance, are generally widely used. In this study, hardened steel (ASTM D2, JIS SKD11, 60HRC) was milled with three physical vapor deposition (PVD)-coated cemented carbide end mill cutters in order to determine effective tool materials for cutting hardened steel at high cutting speeds. The coating films used were (Ti,W)N/(Ti,W,Si)N and (Ti,W)N/(Ti,W,Si,Al)N coating films. (Ti,W,Si,Al)N is a new type of coating film. The inner layer of the (Ti,W)N/(Ti,W,Si)N and (Ti,W)N/(Ti,W,Si,Al)N coating system is (Ti,W)N coating film, and the outer layer is (Ti,W,Si)N and (Ti,W,Si,Al)N coating films, respectively. Furthermore, commercial (Ti,Al)N-based coating film was also used. The following results were obtained: (1) In milling hardened steel at a cutting speed of 3.33 m/s, the tool wear width of the (Ti,W)N/(Ti,W,Si,Al)N-coated tool was smaller than that of the (Ti,W)N/(Ti,W,Si)N-coated tool. And, compared with the commercial (Ti,Al)N, the tool wear width of the (Ti,W)N/(Ti,W,Si,Al)N-coated tool was smaller than that of the (Ti,Al)N-coated tool. (2) The tool wear of the (Ti,W)N/(Ti,W,Si,Al)N-coated tool increased with an increase in cutting speed. (3) The (Ti,W)N/(Ti,W,Si,Al)N-coated cemented carbide was an effective tool material for high-speed cutting below a cutting speed of 3.33 m/s.
Cite this paper
Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.
APA 7
Wada, T., & Iwamoto, K. (2012). Tool Wear Of Titanium/Tungsten/Silicon/Aluminum-Based-Coated End Mill Cutters In Millin Hardened Steel. Zenodo (CERN European Organization for Nuclear Research). https://doi.org/10.5281/zenodo.1328655
MLA 9
Wada, Tadahiro, and Koji Iwamoto. “Tool Wear Of Titanium/Tungsten/Silicon/Aluminum-Based-Coated End Mill Cutters In Millin Hardened Steel.” Zenodo (CERN European Organization for Nuclear Research), 2012. https://doi.org/10.5281/zenodo.1328655.
Chicago
Wada, Tadahiro and Koji Iwamoto. 2012. “Tool Wear Of Titanium/Tungsten/Silicon/Aluminum-Based-Coated End Mill Cutters In Millin Hardened Steel.” Zenodo (CERN European Organization for Nuclear Research). https://doi.org/10.5281/zenodo.1328655.
Harvard
Wada, T. and Iwamoto, K. (2012) ‘Tool Wear Of Titanium/Tungsten/Silicon/Aluminum-Based-Coated End Mill Cutters In Millin Hardened Steel’, Zenodo (CERN European Organization for Nuclear Research). doi:10.5281/zenodo.1328655.
IEEE
T. Wada and K. Iwamoto, “Tool Wear Of Titanium/Tungsten/Silicon/Aluminum-Based-Coated End Mill Cutters In Millin Hardened Steel,” Zenodo (CERN European Organization for Nuclear Research), 2012, doi: 10.5281/zenodo.1328655.
BibTeX
@article{wada2012tool,
title = {{Tool Wear Of Titanium/Tungsten/Silicon/Aluminum-Based-Coated End Mill Cutters In Millin Hardened Steel}},
author = {Wada, Tadahiro and Iwamoto, Koji},
journal = {Zenodo (CERN European Organization for Nuclear Research)},
year = {2012},
doi = {10.5281/zenodo.1328655},
url = {https://doi.org/10.5281/zenodo.1328655}
}
Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)
Topic and keywords
Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- tool wear
- PVD coatings
- TiAlN coating
- high-speed machining
- cutting speed
- fracture toughness
- SKD11 steel
Work with this paper
Most-cited papers in Engineering
- A Closed‐form Equation for Predicting the Hydraulic Conductivity of Unsaturated SoilsMartinus Th. van Genuchten · Soil Science Society of America Journal · 1980 · 28,197 citations
- An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experimentsW. C. Oliver, George M. Pharr · Journal of materials research/Pratt's guide to venture capital sources · 1992 · 27,379 citations
- Digital communicationsOwen Bishop · Routledge eBooks · 2007 · 24,890 citations
- The empirical mode decomposition and the Hilbert spectrum for nonlinear and non-stationary time series analysisNorden Eh Huang, Zhengwei Shen, Steven R. Long and 6 more · Proceedings of the Royal Society A Mathematical Physical and Engineering Sciences · 1998 · 24,008 citations
- Numerical Heat Transfer and Fluid FlowSuhas V. Patankar · CRC Press eBooks · 2018 · 23,491 citations
Questions about this paper
How do I cite this paper in APA style?
Wada, T., & Iwamoto, K. (2012). Tool Wear Of Titanium/Tungsten/Silicon/Aluminum-Based-Coated End Mill Cutters In Millin Hardened Steel. Zenodo (CERN European Organization for Nuclear Research). https://doi.org/10.5281/zenodo.1328655
How many times has this paper been cited?
1 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.
Is this paper free to read?
Yes. It is open access at Zenodo (CERN European Organization for Nuclear Research): sign in and open the full text from this page.
Who wrote this paper?
Tadahiro Wada, Koji Iwamoto.
What is the DOI of this paper?
10.5281/zenodo.1328655, permanently at https://doi.org/10.5281/zenodo.1328655. Sign in and open it from this page.
Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.