Journal article · 2014 · Open access
Tool Life and Flank Wear of Physical Vapour Deposited TiAlN Multilayer Coated Carbide End Mill Inserts when Machining AISI D2 Hardened Steel under Dry Cutting Condition
Advanced materials research, 903, 9–14 · Published 1 February 2014 · DOI 10.4028/www.scientific.net/amr.903.9
In brief
“Tool Life and Flank Wear of Physical Vapour Deposited TiAlN Multilayer Coated Carbide End Mill Inserts when Machining AISI D2 Hardened Steel under Dry Cutting Condition” is a 2014 journal article by N.A.J. Hosni and 2 co-authors, published in Advanced materials research. OpenAlex counts 1 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at Advanced materials research.
- Citations
- 1
- Most cited in
- 2022 (1)
- References
- 10
- Authors
- 3
Abstract
This study investigates the tool wear of PVD TiAlN multilayer coated end mill inserts when machining AISI D2 hardened steel in dry conditions. The experiment tests consisting three levels of cutting speed, Vc (80, 100, 120 m/min) and three levels of radial depth of cut, ae (3, 4, 5 mm) was used for the study. The PVD TiAlN coated carbide insert performs satisfactory under the conditions tested, as reasonable tool life is recorded. By linking the machining tests and tool life curves, the wear behaviour of the coated insert was described. It is observed that wear of the tool mainly occurred on the flank wear. Tool life decreasing and volume material removal (VMR) increasing as cutting speed and radial depth of cut increased due to higher temperature generated and contact area immerse, respectively. Tool failure modes and wear mechanisms were examined at various cutting parameters. Built-up edge (BUE), groove and micro-chipping were found to be the predominant tool failure modes for cutting tools. The highest volume material removal, VMR attained was 3750 mm3, meanwhile the higest tool life, TL was 9.69 min.The combination of cutting conditions that gave the best response for different components of tool wear, tool life and surface integrity.
Cite this paper
Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.
APA 7
Hosni, N., Lajis, M. A., & Rafai, N. H. (2014). Tool Life and Flank Wear of Physical Vapour Deposited TiAlN Multilayer Coated Carbide End Mill Inserts when Machining AISI D2 Hardened Steel under Dry Cutting Condition. Advanced materials research, 903, 9–14. https://doi.org/10.4028/www.scientific.net/amr.903.9
MLA 9
Hosni, N.A.J., et al. “Tool Life and Flank Wear of Physical Vapour Deposited TiAlN Multilayer Coated Carbide End Mill Inserts when Machining AISI D2 Hardened Steel under Dry Cutting Condition.” Advanced materials research, vol. 903, 2014, pp. 9–14. https://doi.org/10.4028/www.scientific.net/amr.903.9.
Chicago
Hosni, N.A.J., Mohd Amri Lajis, and Noor Hakim Rafai. 2014. “Tool Life and Flank Wear of Physical Vapour Deposited TiAlN Multilayer Coated Carbide End Mill Inserts when Machining AISI D2 Hardened Steel under Dry Cutting Condition.” Advanced materials research 903: 9–14. https://doi.org/10.4028/www.scientific.net/amr.903.9.
Harvard
Hosni, N., Lajis, M. A. and Rafai, N. H. (2014) ‘Tool Life and Flank Wear of Physical Vapour Deposited TiAlN Multilayer Coated Carbide End Mill Inserts when Machining AISI D2 Hardened Steel under Dry Cutting Condition’, Advanced materials research, 903, pp. 9–14. doi:10.4028/www.scientific.net/amr.903.9.
IEEE
N. Hosni, M. A. Lajis, and N. H. Rafai, “Tool Life and Flank Wear of Physical Vapour Deposited TiAlN Multilayer Coated Carbide End Mill Inserts when Machining AISI D2 Hardened Steel under Dry Cutting Condition,” Advanced materials research, vol. 903, pp. 9–14, 2014, doi: 10.4028/www.scientific.net/amr.903.9.
BibTeX
@article{hosni2014tool,
title = {{Tool Life and Flank Wear of Physical Vapour Deposited TiAlN Multilayer Coated Carbide End Mill Inserts when Machining AISI D2 Hardened Steel under Dry Cutting Condition}},
author = {Hosni, N.A.J. and Lajis, Mohd Amri and Rafai, Noor Hakim},
journal = {Advanced materials research},
year = {2014},
volume = {903},
pages = {9--14},
doi = {10.4028/www.scientific.net/amr.903.9},
url = {https://doi.org/10.4028/www.scientific.net/amr.903.9}
}
Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)
Topic and keywords
Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- tool life
- flank wear
- PVD coatings
- dry machining
- cutting speed
- radial depth of cut
- tool failure modes
- built-up edge
Work with this paper
Most-cited papers in Engineering
- A Closed‐form Equation for Predicting the Hydraulic Conductivity of Unsaturated SoilsMartinus Th. van Genuchten · Soil Science Society of America Journal · 1980 · 28,197 citations
- An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experimentsW. C. Oliver, George M. Pharr · Journal of materials research/Pratt's guide to venture capital sources · 1992 · 27,379 citations
- Digital communicationsOwen Bishop · Routledge eBooks · 2007 · 24,890 citations
- The empirical mode decomposition and the Hilbert spectrum for nonlinear and non-stationary time series analysisNorden Eh Huang, Zhengwei Shen, Steven R. Long and 6 more · Proceedings of the Royal Society A Mathematical Physical and Engineering Sciences · 1998 · 24,008 citations
- Numerical Heat Transfer and Fluid FlowSuhas V. Patankar · CRC Press eBooks · 2018 · 23,491 citations
Questions about this paper
How do I cite this paper in APA style?
Hosni, N., Lajis, M. A., & Rafai, N. H. (2014). Tool Life and Flank Wear of Physical Vapour Deposited TiAlN Multilayer Coated Carbide End Mill Inserts when Machining AISI D2 Hardened Steel under Dry Cutting Condition. Advanced materials research, 903, 9–14. https://doi.org/10.4028/www.scientific.net/amr.903.9
How many times has this paper been cited?
1 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.
Is this paper free to read?
Yes. It is open access at Advanced materials research: sign in and open the full text from this page.
Who wrote this paper?
N.A.J. Hosni, Mohd Amri Lajis, Noor Hakim Rafai.
What is the DOI of this paper?
10.4028/www.scientific.net/amr.903.9, permanently at https://doi.org/10.4028/www.scientific.net/amr.903.9. Sign in and open it from this page.
Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.