Journal article · 2010 · Open access
Ti–Si–C Thin Films Produced by Magnetron Sputtering: Correlation Between Physical Properties, Mechanical Properties and Tribological Behavior
Journal of Nanoscience and Nanotechnology, 10(4), 2926–2932 · Published 1 April 2010 · DOI 10.1166/jnn.2010.1428
In brief
“Ti–Si–C Thin Films Produced by Magnetron Sputtering: Correlation Between Physical Properties, Mechanical Properties and Tribological Behavior” is a 2010 journal article by L. Cunha and 6 co-authors, published in Journal of Nanoscience and Nanotechnology. OpenAlex counts 11 citations as of 16 November 2026. It is open access: the full text is free to read at Portuguese National Funding Agency for Science, Research and Technology (RCAAP Project by FCT).
- Citations
- 11
- Most cited in
- 2015 (4)
- Field-weighted impact
- 0.41
- Authors
- 7
Abstract
Ti-Si-C thin films were deposited onto silicon, stainless steel and high-speed steel substrates by magnetron sputtering, using different chamber configurations. The composition of the produced films was obtained by Electron Probe Micro-Analysis (EPMA) and the structure by X-ray diffraction (XRD). The hardness and residual stresses were obtained by depth-sensing indentation and substrate deflection measurements (using Stoney's equation), respectively. The tribological behavior of the produced films was studied by pin-on-disc. The increase of the concentration of non-metallic elements (carbon and silicon) caused significant changes in their properties. Structural analysis revealed the possibility of the coexistence of different phases in the prepared films, namely Ti metallic phase (alpha-Ti or beta-Ti) in the films with higher Ti content. The coatings with highest carbon contents, exhibited mainly a sub-stoichiometric fcc NaCI TiC-type structure. These structural changes were also confirmed by resistivity measurements, whose values ranged from 10(3) omega/sq for low non-metal concentration, up to 10(6) omega/sq for the highest metalloid concentration. A strong increase of hardness and residual stresses was observed with the increase of the non-metal concentration in the films. The hardness (H) values ranged between 11 and 27 GPa, with a clear dependence on both crystalline structure and composition features. Following the mechanical behavior, the tribological results showed similar trends, with both friction coefficients and wear revealing also a straight correlation with the composition and crystalline structure of the coatings.
Cite this paper
Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.
APA 7
Cunha, L., Vaz, F., Moura, C., Munteanu, D., Ionescu, C., Rivière, J., & Le Bourhis, É. (2010). Ti–Si–C Thin Films Produced by Magnetron Sputtering: Correlation Between Physical Properties, Mechanical Properties and Tribological Behavior. Journal of Nanoscience and Nanotechnology, 10(4), 2926–2932. https://doi.org/10.1166/jnn.2010.1428
MLA 9
Cunha, L., et al. “Ti–Si–C Thin Films Produced by Magnetron Sputtering: Correlation Between Physical Properties, Mechanical Properties and Tribological Behavior.” Journal of Nanoscience and Nanotechnology, vol. 10, no. 4, 2010, pp. 2926–2932. https://doi.org/10.1166/jnn.2010.1428.
Chicago
Cunha, L., Filipe Vaz, C. Moura, Daniel Munteanu, Cristina Ionescu, J.P. Rivière, and Éric Le Bourhis. 2010. “Ti–Si–C Thin Films Produced by Magnetron Sputtering: Correlation Between Physical Properties, Mechanical Properties and Tribological Behavior.” Journal of Nanoscience and Nanotechnology 10 (4): 2926–2932. https://doi.org/10.1166/jnn.2010.1428.
Harvard
Cunha, L. et al. (2010) ‘Ti–Si–C Thin Films Produced by Magnetron Sputtering: Correlation Between Physical Properties, Mechanical Properties and Tribological Behavior’, Journal of Nanoscience and Nanotechnology, 10(4), pp. 2926–2932. doi:10.1166/jnn.2010.1428.
IEEE
L. Cunha et al., “Ti–Si–C Thin Films Produced by Magnetron Sputtering: Correlation Between Physical Properties, Mechanical Properties and Tribological Behavior,” Journal of Nanoscience and Nanotechnology, vol. 10, no. 4, pp. 2926–2932, 2010, doi: 10.1166/jnn.2010.1428.
BibTeX
@article{cunha2010thin,
title = {{Ti–Si–C Thin Films Produced by Magnetron Sputtering: Correlation Between Physical Properties, Mechanical Properties and Tribological Behavior}},
author = {Cunha, L. and Vaz, Filipe and Moura, C. and Munteanu, Daniel and Ionescu, Cristina and Rivière, J.P. and Le Bourhis, Éric},
journal = {Journal of Nanoscience and Nanotechnology},
year = {2010},
volume = {10},
number = {4},
pages = {2926--2932},
doi = {10.1166/jnn.2010.1428},
url = {https://doi.org/10.1166/jnn.2010.1428}
}
Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)
Citations by year
| Year | Citations | Share of the best year |
|---|---|---|
| 2014 | 3 | |
| 2015 | 4 | |
| 2016 | 1 | |
| 2026 | 1 |
Its field-weighted citation impact is 0.41: it has been cited 0.41 times as often as the average work of the same field, type and year (1.00 is the world average).
Topic and keywords
Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics
- titanium carbide
- magnetron sputtering
- hardness
- residual stress
- tribological properties
- friction coefficient
- wear
- carbon content
Work with this paper
Most-cited papers in Engineering
- A Closed‐form Equation for Predicting the Hydraulic Conductivity of Unsaturated SoilsMartinus Th. van Genuchten · Soil Science Society of America Journal · 1980 · 28,197 citations
- An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experimentsW. C. Oliver, George M. Pharr · Journal of materials research/Pratt's guide to venture capital sources · 1992 · 27,379 citations
- Digital communicationsOwen Bishop · Routledge eBooks · 2007 · 24,890 citations
- The empirical mode decomposition and the Hilbert spectrum for nonlinear and non-stationary time series analysisNorden Eh Huang, Zhengwei Shen, Steven R. Long and 6 more · Proceedings of the Royal Society A Mathematical Physical and Engineering Sciences · 1998 · 24,008 citations
- Numerical Heat Transfer and Fluid FlowSuhas V. Patankar · CRC Press eBooks · 2018 · 23,491 citations
Questions about this paper
How do I cite this paper in APA style?
Cunha, L., Vaz, F., Moura, C., Munteanu, D., Ionescu, C., Rivière, J., & Le Bourhis, É. (2010). Ti–Si–C Thin Films Produced by Magnetron Sputtering: Correlation Between Physical Properties, Mechanical Properties and Tribological Behavior. Journal of Nanoscience and Nanotechnology, 10(4), 2926–2932. https://doi.org/10.1166/jnn.2010.1428
How many times has this paper been cited?
11 times, according to OpenAlex on 16 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.
Is this paper free to read?
Yes. It is open access: read the free full text at Portuguese National Funding Agency for Science, Research and Technology (RCAAP Project by FCT).
Who wrote this paper?
L. Cunha, Filipe Vaz, C. Moura, Daniel Munteanu, Cristina Ionescu, J.P. Rivière, Éric Le Bourhis.
What is the DOI of this paper?
10.1166/jnn.2010.1428. The permanent link is https://doi.org/10.1166/jnn.2010.1428.
Bibliographic data from OpenAlex (CC0), last checked 16 November 2026. ResearchGuru does not host this paper; the links go to the publisher or the repository that does.