Journal article · 2023 · Open access

The study of the tribological properties under high contact pressure conditions of TiN, TiC and TiCN coatings deposited by the magnetron sputtering method on the AISI 304 stainless steel substrate

Axaule Mamaeva, Kenzhegulov Aidar Karaulovich, А.В. Паничкин, Zhasulan Alibekov, Balzhan Kshibekova, W. Wieleba, Tadeusz Leśniewski, Nauryzbek Bakhytuly

Materials Science-Poland, 41(1), 1–14 · Published 1 March 2023 · DOI 10.2478/msp-2022-0055

Open PDFView at the publisherCite this paper

In brief

“The study of the tribological properties under high contact pressure conditions of TiN, TiC and TiCN coatings deposited by the magnetron sputtering method on the AISI 304 stainless steel substrate” is a 2023 journal article by Axaule Mamaeva and 7 co-authors, published in Materials Science-Poland. OpenAlex counts 19 citations as of 17 November 2026. It is open access under a CC BY-NC-ND licence: the full text is free to read at Materials Science-Poland.

Citations
19
Most cited in
2024 (8)
Field-weighted impact
1.89
References
18
Authors
8

Abstract

Titanium carbonitride coatings are widely used to improve the wear resistance of surfaces. The results of tribological investigations of TiC, TiN, and TiCN coatings deposited on an AISI 304 steel substrate by the magnetron sputtering method were presented. The research aimed to describe the wear processes of the coatings during friction in an emergency situation, i.e. with a lack of lubrication and concentration of pressure in a small contact area. Tribological tests were performed on a ball-on-disk tribotester in reciprocating motion under technically dry friction conditions. The Hertz pressure in the contact area was ph = 2500-2700 MPa. Additionally, scratch tests and microscopic observations of the surfaces of the samples were performed after tribological tests to describe the wear process of the coatings. The results showed cracking, and coatings detachment from the substrate occur during friction. Deformation wear was observed as bulges in the material at the edge of the friction path. The deformation occurred primarily in the substrate material despite friction occurring on the surface of the coating. The best coating in terms of tribological properties was the TiN coating, which showed the highest resistance to wear in an emergency situation and the friction coefficient in the final stage of the test (above 90 cycles of movement) was only slightly higher than the values recorded for the other coatings. The TiN coating had high hardness, showed good adhesion to the substrate, and was not cracked, protecting it from damage.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Mamaeva, A., Karaulovich, K. A., Паничкин, А., Alibekov, Z., Kshibekova, B., Wieleba, W., Leśniewski, T., & Bakhytuly, N. (2023). The study of the tribological properties under high contact pressure conditions of TiN, TiC and TiCN coatings deposited by the magnetron sputtering method on the AISI 304 stainless steel substrate. Materials Science-Poland, 41(1), 1–14. https://doi.org/10.2478/msp-2022-0055

MLA 9

Mamaeva, Axaule, et al. “The study of the tribological properties under high contact pressure conditions of TiN, TiC and TiCN coatings deposited by the magnetron sputtering method on the AISI 304 stainless steel substrate.” Materials Science-Poland, vol. 41, no. 1, 2023, pp. 1–14. https://doi.org/10.2478/msp-2022-0055.

Chicago

Mamaeva, Axaule, Kenzhegulov Aidar Karaulovich, А.В. Паничкин, Zhasulan Alibekov, Balzhan Kshibekova, W. Wieleba, Tadeusz Leśniewski, and Nauryzbek Bakhytuly. 2023. “The study of the tribological properties under high contact pressure conditions of TiN, TiC and TiCN coatings deposited by the magnetron sputtering method on the AISI 304 stainless steel substrate.” Materials Science-Poland 41 (1): 1–14. https://doi.org/10.2478/msp-2022-0055.

Harvard

Mamaeva, A. et al. (2023) ‘The study of the tribological properties under high contact pressure conditions of TiN, TiC and TiCN coatings deposited by the magnetron sputtering method on the AISI 304 stainless steel substrate’, Materials Science-Poland, 41(1), pp. 1–14. doi:10.2478/msp-2022-0055.

IEEE

A. Mamaeva et al., “The study of the tribological properties under high contact pressure conditions of TiN, TiC and TiCN coatings deposited by the magnetron sputtering method on the AISI 304 stainless steel substrate,” Materials Science-Poland, vol. 41, no. 1, pp. 1–14, 2023, doi: 10.2478/msp-2022-0055.

BibTeX

@article{mamaeva2023study,
  title     = {{The study of the tribological properties under high contact pressure conditions of TiN, TiC and TiCN coatings deposited by the magnetron sputtering method on the AISI 304 stainless steel substrate}},
  author    = {Mamaeva, Axaule and Karaulovich, Kenzhegulov Aidar and Паничкин, А.В. and Alibekov, Zhasulan and Kshibekova, Balzhan and Wieleba, W. and Leśniewski, Tadeusz and Bakhytuly, Nauryzbek},
  journal   = {Materials Science-Poland},
  year      = {2023},
  volume    = {41},
  number    = {1},
  pages     = {1--14},
  doi       = {10.2478/msp-2022-0055},
  url       = {https://doi.org/10.2478/msp-2022-0055}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
202311
202488
202566
202644

Its field-weighted citation impact is 1.89: it has been cited 1.89 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics

  • TiN coating
  • TiC coating
  • TiCN coating
  • titanium carbonitride
  • 304 stainless steel
  • magnetron sputtering
  • tribological properties
  • Coulomb friction

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Mamaeva, A., Karaulovich, K. A., Паничкин, А., Alibekov, Z., Kshibekova, B., Wieleba, W., Leśniewski, T., & Bakhytuly, N. (2023). The study of the tribological properties under high contact pressure conditions of TiN, TiC and TiCN coatings deposited by the magnetron sputtering method on the AISI 304 stainless steel substrate. Materials Science-Poland, 41(1), 1–14. https://doi.org/10.2478/msp-2022-0055

How many times has this paper been cited?

19 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Materials Science-Poland: sign in and open the PDF from this page.

Who wrote this paper?

Axaule Mamaeva, Kenzhegulov Aidar Karaulovich, А.В. Паничкин, Zhasulan Alibekov, Balzhan Kshibekova, W. Wieleba, Tadeusz Leśniewski, Nauryzbek Bakhytuly.

What is the DOI of this paper?

10.2478/msp-2022-0055, permanently at https://doi.org/10.2478/msp-2022-0055. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.