Paper · 2015 · Open access
The Deposition Rate, Hardness and Tribological Properties of a-C:H Coatings with a Tungsten Filament-Assisted Ionized Reaction Gas
Key engineering materials, 642, 135–140 · Published 15 April 2015 · DOI 10.4028/www.scientific.net/kem.642.135
In brief
“The Deposition Rate, Hardness and Tribological Properties of a-C:H Coatings with a Tungsten Filament-Assisted Ionized Reaction Gas” is a 2015 paper by W.H. Kao and 3 co-authors, published in Key engineering materials. OpenAlex counts 0 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at Key engineering materials.
- Citations
- 0
- References
- 5
- Authors
- 4
Abstract
The a-C:H coatings were deposited on AISI M2 steel disks using an unbalanced magnetron sputtering technique with a single titanium metal target, three graphite targets and mixed methane/ acetylene reactive gas. The various currents (9A-17A) were applied to the tungsten filament to enhance ionization rate of reactive gas. Tribological properties of a-C:H coatings were conducted used reciprocating friction tester. The results show that the tungsten filament current has a significant effect on the deposition rate, hardness and tribological properties of the coatings. With the increase of the tungsten filament current, the deposition rate and hardness of the coating increases, respectively. In sliding against an AISI 52100 steel ball for 24 minutes, all of coatings reduce the wear depth by a factor of at least 11 compared to that observed on an uncoated substrate. The 17A coating yields the best tribological properties that are the minimum wear depth, the lowest friction coefficient and the maximum lifetime when sliding against an AISI 52100 steel ball.
Cite this paper
Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.
APA 7
Kao, W., Su, Y., Horng, J., & Huang, H. C. (2015). The Deposition Rate, Hardness and Tribological Properties of a-C:H Coatings with a Tungsten Filament-Assisted Ionized Reaction Gas. Key engineering materials, 642, 135–140. https://doi.org/10.4028/www.scientific.net/kem.642.135
MLA 9
Kao, W.H., et al. “The Deposition Rate, Hardness and Tribological Properties of a-C:H Coatings with a Tungsten Filament-Assisted Ionized Reaction Gas.” Key engineering materials, vol. 642, 2015, pp. 135–140. https://doi.org/10.4028/www.scientific.net/kem.642.135.
Chicago
Kao, W.H., Yan Su, Jeng‐Haur Horng, and Hsi Chuan Huang. 2015. “The Deposition Rate, Hardness and Tribological Properties of a-C:H Coatings with a Tungsten Filament-Assisted Ionized Reaction Gas.” Key engineering materials 642: 135–140. https://doi.org/10.4028/www.scientific.net/kem.642.135.
Harvard
Kao, W. et al. (2015) ‘The Deposition Rate, Hardness and Tribological Properties of a-C:H Coatings with a Tungsten Filament-Assisted Ionized Reaction Gas’, Key engineering materials, 642, pp. 135–140. doi:10.4028/www.scientific.net/kem.642.135.
IEEE
W. Kao, Y. Su, J. Horng, and H. C. Huang, “The Deposition Rate, Hardness and Tribological Properties of a-C:H Coatings with a Tungsten Filament-Assisted Ionized Reaction Gas,” Key engineering materials, vol. 642, pp. 135–140, 2015, doi: 10.4028/www.scientific.net/kem.642.135.
BibTeX
@article{kao2015deposition,
title = {{The Deposition Rate, Hardness and Tribological Properties of a-C:H Coatings with a Tungsten Filament-Assisted Ionized Reaction Gas}},
author = {Kao, W.H. and Su, Yan and Horng, Jeng‐Haur and Huang, Hsi Chuan},
journal = {Key engineering materials},
year = {2015},
volume = {642},
pages = {135--140},
doi = {10.4028/www.scientific.net/kem.642.135},
url = {https://doi.org/10.4028/www.scientific.net/kem.642.135}
}
Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)
Topic and keywords
Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics
- a-C:H coatings
- hydrogenated amorphous carbon
- deposition rate
- coating hardness
- tribological properties
- wear resistance
- friction coefficient
- M2 high-speed steel
Work with this paper
Most-cited papers in Engineering
- A Closed‐form Equation for Predicting the Hydraulic Conductivity of Unsaturated SoilsMartinus Th. van Genuchten · Soil Science Society of America Journal · 1980 · 28,197 citations
- An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experimentsW. C. Oliver, George M. Pharr · Journal of materials research/Pratt's guide to venture capital sources · 1992 · 27,379 citations
- Digital communicationsOwen Bishop · Routledge eBooks · 2007 · 24,890 citations
- The empirical mode decomposition and the Hilbert spectrum for nonlinear and non-stationary time series analysisNorden Eh Huang, Zhengwei Shen, Steven R. Long and 6 more · Proceedings of the Royal Society A Mathematical Physical and Engineering Sciences · 1998 · 24,008 citations
- Numerical Heat Transfer and Fluid FlowSuhas V. Patankar · CRC Press eBooks · 2018 · 23,491 citations
Questions about this paper
How do I cite this paper in APA style?
Kao, W., Su, Y., Horng, J., & Huang, H. C. (2015). The Deposition Rate, Hardness and Tribological Properties of a-C:H Coatings with a Tungsten Filament-Assisted Ionized Reaction Gas. Key engineering materials, 642, 135–140. https://doi.org/10.4028/www.scientific.net/kem.642.135
How many times has this paper been cited?
0 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.
Is this paper free to read?
Yes. It is open access at Key engineering materials: sign in and open the full text from this page.
Who wrote this paper?
W.H. Kao, Yan Su, Jeng‐Haur Horng, Hsi Chuan Huang.
What is the DOI of this paper?
10.4028/www.scientific.net/kem.642.135, permanently at https://doi.org/10.4028/www.scientific.net/kem.642.135. Sign in and open it from this page.
Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.