Journal article · 2018 · Open access

Structure, Mechanical and Tribological Properties of Me-Doped Diamond-Like Carbon (DLC) (Me = Al, Ti, or Nb) Hydrogenated Amorphous Carbon Coatings

Imane Bouabibsa, Salim Lamri, Frédéric Sanchette

Coatings, 8(10), 370 · Published 19 October 2018 · DOI 10.3390/coatings8100370

Free PDFView at the publisherCite this paper

In brief

“Structure, Mechanical and Tribological Properties of Me-Doped Diamond-Like Carbon (DLC) (Me = Al, Ti, or Nb) Hydrogenated Amorphous Carbon Coatings” is a 2018 journal article by Imane Bouabibsa and 2 co-authors, published in Coatings. OpenAlex counts 73 citations as of 16 November 2026. It is open access under a CC BY licence: the full text is free to read at Coatings.

Citations
73
Most cited in
2023 (14)
Field-weighted impact
2.77
References
63
Authors
3

Abstract

Metal containing hydrogenated diamond-like carbon coatings (Me-DLC, Me = Al, Ti, or Nb) of 3 ± 0.2 μm thickness were deposited by a magnetron sputtering-RFPECVD hybrid process in an Ar/H2/C2H2 mixture. The composition and structure were investigated by Energy Dispersive X-ray Spectroscopy (EDS), X-ray Diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy. The residual stress was measured using the curvature method and nanoindentation was used to determine the hardness and the Young’s modulus. A Ball-on-disk tribometer was employed to investigate the frictional properties and sliding wear resistance of films. The results show that the properties depend on the nature and the Me content in the coatings. The doping of the DLC coatings leads to a decrease in hardness, Young’s modulus, and residual stresses. Wear rate of the films first decreases with intermediate Me contents and then increases for higher Me contents. Significant improvements in the friction coefficient on steel as well as in the wear rate are observed for all Al-DLC coatings, and, concerning the friction coefficient, the lowest value is measured at 0.04 as compared to 0.07 for the undoped DLC.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Bouabibsa, I., Lamri, S., & Sanchette, F. (2018). Structure, Mechanical and Tribological Properties of Me-Doped Diamond-Like Carbon (DLC) (Me = Al, Ti, or Nb) Hydrogenated Amorphous Carbon Coatings. Coatings, 8(10), 370. https://doi.org/10.3390/coatings8100370

MLA 9

Bouabibsa, Imane, et al. “Structure, Mechanical and Tribological Properties of Me-Doped Diamond-Like Carbon (DLC) (Me = Al, Ti, or Nb) Hydrogenated Amorphous Carbon Coatings.” Coatings, vol. 8, no. 10, 2018, p. 370. https://doi.org/10.3390/coatings8100370.

Chicago

Bouabibsa, Imane, Salim Lamri, and Frédéric Sanchette. 2018. “Structure, Mechanical and Tribological Properties of Me-Doped Diamond-Like Carbon (DLC) (Me = Al, Ti, or Nb) Hydrogenated Amorphous Carbon Coatings.” Coatings 8 (10): 370. https://doi.org/10.3390/coatings8100370.

Harvard

Bouabibsa, I., Lamri, S. and Sanchette, F. (2018) ‘Structure, Mechanical and Tribological Properties of Me-Doped Diamond-Like Carbon (DLC) (Me = Al, Ti, or Nb) Hydrogenated Amorphous Carbon Coatings’, Coatings, 8(10), p. 370. doi:10.3390/coatings8100370.

IEEE

I. Bouabibsa, S. Lamri, and F. Sanchette, “Structure, Mechanical and Tribological Properties of Me-Doped Diamond-Like Carbon (DLC) (Me = Al, Ti, or Nb) Hydrogenated Amorphous Carbon Coatings,” Coatings, vol. 8, no. 10, p. 370, 2018, doi: 10.3390/coatings8100370.

BibTeX

@article{bouabibsa2018structure,
  title     = {{Structure, Mechanical and Tribological Properties of Me-Doped Diamond-Like Carbon (DLC) (Me = Al, Ti, or Nb) Hydrogenated Amorphous Carbon Coatings}},
  author    = {Bouabibsa, Imane and Lamri, Salim and Sanchette, Frédéric},
  journal   = {Coatings},
  year      = {2018},
  volume    = {8},
  number    = {10},
  pages     = {370},
  doi       = {10.3390/coatings8100370},
  url       = {https://doi.org/10.3390/coatings8100370}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
201911
202088
20211010
202277
20231414
202499
20251414
20261010

Its field-weighted citation impact is 2.77: it has been cited 2.77 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics

  • aluminum doping
  • titanium doping
  • niobium doping
  • residual stress
  • hardness
  • Young's modulus
  • friction coefficient
  • sliding wear resistance

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Bouabibsa, I., Lamri, S., & Sanchette, F. (2018). Structure, Mechanical and Tribological Properties of Me-Doped Diamond-Like Carbon (DLC) (Me = Al, Ti, or Nb) Hydrogenated Amorphous Carbon Coatings. Coatings, 8(10), 370. https://doi.org/10.3390/coatings8100370

How many times has this paper been cited?

73 times, according to OpenAlex on 16 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access: read the free full text at Coatings.

Who wrote this paper?

Imane Bouabibsa, Salim Lamri, Frédéric Sanchette.

What is the DOI of this paper?

10.3390/coatings8100370. The permanent link is https://doi.org/10.3390/coatings8100370.

Bibliographic data from OpenAlex (CC0), last checked 16 November 2026. ResearchGuru does not host this paper; the links go to the publisher or the repository that does.