Journal article · 2025 · Open access

Structure and properties of antifriction Ti–Cr–Ni–Cu–Sn–P–C–N coatings deposited by magnetron sputtering of composite SHS targets

Ph. V. Kiryukhantsev–Korneev, A. D. Chertova, Yu. С. Pogozhev, Evgeny Alexandrovich Levashov

Powder Metallurgy аnd Functional Coatings, 19(3), 60–73 · Published 25 June 2025 · DOI 10.17073/1997-308x-2025-3-60-73

Open PDFView at the publisherCite this paper

In brief

“Structure and properties of antifriction Ti–Cr–Ni–Cu–Sn–P–C–N coatings deposited by magnetron sputtering of composite SHS targets” is a 2025 journal article by Ph. V. Kiryukhantsev–Korneev and 3 co-authors, published in Powder Metallurgy аnd Functional Coatings. OpenAlex counts 1 citations as of 17 November 2026, which puts it in the top 9% of works published in 2025 by citations. It is open access under a CC BY-NC-ND licence: the full text is free to read at Powder Metallurgy аnd Functional Coatings.

Citations
1
Most cited in
2026 (1)
Field-weighted impact
0.26
References
51
Authors
4

Abstract

This article focuses on the production of wear-resistant antifriction coatings by magnetron sputtering using composite SHS-fabricated cathode targets of TiCrNiC and TiCrNiC–CuSnP in Ar and Ar + 15 % N2 atmospheres. Special attention is given to the phase composition and structure of the targets, produced via the self-propagating high-temperature synthesis (SHS) method. Structural charac­terization of the targets and coatings was carried out using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and glow discharge optical emission spectroscopy (GDOES). The mechanical and tribological properties of the coatings were evaluated using nanoindentation, scratch testing, and pin-on-disk sliding wear tests. The resulting coatings exhibi­ted dense, defect-free microstructures with a uniform elemental distribution through the thickness. The coating matrix was primarily composed of FCC phases c-TiC(N) and c-(Ni,Cr). The addition of copper to the coating led to the formation of an additional amorphous Cu-based phase. The coatings demonstrated hardness in the range of 18–21 GPa and an elastic modulus of 220–235 GPa. High critical loads for adhesive failure were observed, reaching up to 60 N. The non-reactive Ti–Cr–Ni–C coatings exhibited the lowest friction coefficients (0.17–0.18), while other compositions showed values ranging from 0.22 to 0.25, in contrast to 0.63–0.71 for uncoated steel substrates. The specific wear rate varied between 1.1·10–6 and 5.0·10–6 mm3/(N·m) depending on the counterbody material and coating composition, which is nearly two orders of magnitude lower than that of the substrate material ((1.2÷2.7)·10–4 mm3/(N·m).

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Kiryukhantsev–Korneev, P. V., Chertova, A. D., Pogozhev, Y. С., & Levashov, E. A. (2025). Structure and properties of antifriction Ti–Cr–Ni–Cu–Sn–P–C–N coatings deposited by magnetron sputtering of composite SHS targets. Powder Metallurgy аnd Functional Coatings, 19(3), 60–73. https://doi.org/10.17073/1997-308x-2025-3-60-73

MLA 9

Kiryukhantsev–Korneev, Ph. V., et al. “Structure and properties of antifriction Ti–Cr–Ni–Cu–Sn–P–C–N coatings deposited by magnetron sputtering of composite SHS targets.” Powder Metallurgy аnd Functional Coatings, vol. 19, no. 3, 2025, pp. 60–73. https://doi.org/10.17073/1997-308x-2025-3-60-73.

Chicago

Kiryukhantsev–Korneev, Ph. V., A. D. Chertova, Yu. С. Pogozhev, and Evgeny Alexandrovich Levashov. 2025. “Structure and properties of antifriction Ti–Cr–Ni–Cu–Sn–P–C–N coatings deposited by magnetron sputtering of composite SHS targets.” Powder Metallurgy аnd Functional Coatings 19 (3): 60–73. https://doi.org/10.17073/1997-308x-2025-3-60-73.

Harvard

Kiryukhantsev–Korneev, P. V. et al. (2025) ‘Structure and properties of antifriction Ti–Cr–Ni–Cu–Sn–P–C–N coatings deposited by magnetron sputtering of composite SHS targets’, Powder Metallurgy аnd Functional Coatings, 19(3), pp. 60–73. doi:10.17073/1997-308x-2025-3-60-73.

IEEE

P. V. Kiryukhantsev–Korneev, A. D. Chertova, Y. С. Pogozhev, and E. A. Levashov, “Structure and properties of antifriction Ti–Cr–Ni–Cu–Sn–P–C–N coatings deposited by magnetron sputtering of composite SHS targets,” Powder Metallurgy аnd Functional Coatings, vol. 19, no. 3, pp. 60–73, 2025, doi: 10.17073/1997-308x-2025-3-60-73.

BibTeX

@article{kiryukhantsevkorneev2025structure,
  title     = {{Structure and properties of antifriction Ti–Cr–Ni–Cu–Sn–P–C–N coatings deposited by magnetron sputtering of composite SHS targets}},
  author    = {Kiryukhantsev–Korneev, Ph. V. and Chertova, A. D. and Pogozhev, Yu. С. and Levashov, Evgeny Alexandrovich},
  journal   = {Powder Metallurgy аnd Functional Coatings},
  year      = {2025},
  volume    = {19},
  number    = {3},
  pages     = {60--73},
  doi       = {10.17073/1997-308x-2025-3-60-73},
  url       = {https://doi.org/10.17073/1997-308x-2025-3-60-73}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics

  • antifriction coatings
  • self-propagating high-temperature synthesis
  • magnetron sputtering
  • phase composition
  • tribological properties
  • wear resistance
  • friction coefficient
  • specific wear rate

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Kiryukhantsev–Korneev, P. V., Chertova, A. D., Pogozhev, Y. С., & Levashov, E. A. (2025). Structure and properties of antifriction Ti–Cr–Ni–Cu–Sn–P–C–N coatings deposited by magnetron sputtering of composite SHS targets. Powder Metallurgy аnd Functional Coatings, 19(3), 60–73. https://doi.org/10.17073/1997-308x-2025-3-60-73

How many times has this paper been cited?

1 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Powder Metallurgy аnd Functional Coatings: sign in and open the PDF from this page.

Who wrote this paper?

Ph. V. Kiryukhantsev–Korneev, A. D. Chertova, Yu. С. Pogozhev, Evgeny Alexandrovich Levashov.

What is the DOI of this paper?

10.17073/1997-308x-2025-3-60-73, permanently at https://doi.org/10.17073/1997-308x-2025-3-60-73. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.