Journal article · 2022 · Open access
Self-lubricating CrAlMoN high performance tool coatings for machining of TiAl6V4
Production Engineering, 17(3-4), 437–444 · Published 14 September 2022 · DOI 10.1007/s11740-022-01161-8
In brief
“Self-lubricating CrAlMoN high performance tool coatings for machining of TiAl6V4” is a 2022 journal article by Kirsten Bobzin and 6 co-authors, published in Production Engineering. OpenAlex counts 5 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at Production Engineering.
- Citations
- 5
- Most cited in
- 2026 (2)
- Field-weighted impact
- 0.28
- References
- 18
- Authors
- 7
Abstract
TiAl6V4 allows significant performance improvements in industrial applications. However, the machining is a considerable challenge due to low thermal conductivity, Young’s modulus and strong adhesion tendency. This leads to high thermal and mechanical loads on the cutting edge resulting in early tool failure. Today, uncoated cemented carbide tools are commonly used. However, temperature active physical vapor deposition (PVD) coatings like CrAlVN and CrAlMoN provide a promising approach to increase tool life. For this, the coating’s ability to form lubricating oxide phases is vital. In the present study, CrAlVN and CrAlMoN coatings were investigated to determine the more suitable version for increasing the economic efficiency of machining TiAl6V4. The coatings were deposited by hybrid direct current magnetron sputtering/high power pulsed magnetron sputtering (dcMS/HPPMS) processes. Morphology, thickness, chemical composition, indentation hardness, indentation modulus and oxide phase composition were analyzed. Moreover, friction and wear behavior of the coated tools were determined using a pin on disc (PoD) tribometer at various temperatures. Additionally, tool life and deformation behavior were analyzed after turning TiAl6V4. The CrAlVN and CrAlMoN coatings show a dense morphology and a smooth surface topography. Both variants have a good adhesion to the cemented carbide tools. For increased temperatures, the tribological analyses showed a reduction in the coefficient of friction. In case of CrAlMoN coated samples, a friction reduction compared to CrAlVN was observed at lower temperatures. Due to this, an increased tool life was achieved for CrAlMoN coated cutting inserts during turning of TiAl6V4.
Cite this paper
Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.
APA 7
Bobzin, K., Kalscheuer, C., Carlet, M., Stachowski, N., Hintze, W., Möller, C., & Ploog, P. (2022). Self-lubricating CrAlMoN high performance tool coatings for machining of TiAl6V4. Production Engineering, 17(3-4), 437–444. https://doi.org/10.1007/s11740-022-01161-8
MLA 9
Bobzin, Kirsten, et al. “Self-lubricating CrAlMoN high performance tool coatings for machining of TiAl6V4.” Production Engineering, vol. 17, no. 3-4, 2022, pp. 437–444. https://doi.org/10.1007/s11740-022-01161-8.
Chicago
Bobzin, Kirsten, C. Kalscheuer, M. Carlet, Nina Stachowski, Wolfgang Hintze, Carsten Möller, and P. Ploog. 2022. “Self-lubricating CrAlMoN high performance tool coatings for machining of TiAl6V4.” Production Engineering 17 (3-4): 437–444. https://doi.org/10.1007/s11740-022-01161-8.
Harvard
Bobzin, K. et al. (2022) ‘Self-lubricating CrAlMoN high performance tool coatings for machining of TiAl6V4’, Production Engineering, 17(3-4), pp. 437–444. doi:10.1007/s11740-022-01161-8.
IEEE
K. Bobzin et al., “Self-lubricating CrAlMoN high performance tool coatings for machining of TiAl6V4,” Production Engineering, vol. 17, no. 3-4, pp. 437–444, 2022, doi: 10.1007/s11740-022-01161-8.
BibTeX
@article{bobzin2022self,
title = {{Self-lubricating CrAlMoN high performance tool coatings for machining of TiAl6V4}},
author = {Bobzin, Kirsten and Kalscheuer, C. and Carlet, M. and Stachowski, Nina and Hintze, Wolfgang and Möller, Carsten and Ploog, P.},
journal = {Production Engineering},
year = {2022},
volume = {17},
number = {3-4},
pages = {437--444},
doi = {10.1007/s11740-022-01161-8},
url = {https://doi.org/10.1007/s11740-022-01161-8}
}
Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)
Citations by year
| Year | Citations | Share of the best year |
|---|---|---|
| 2023 | 1 | |
| 2024 | 1 | |
| 2025 | 1 | |
| 2026 | 2 |
Its field-weighted citation impact is 0.28: it has been cited 0.28 times as often as the average work of the same field, type and year (1.00 is the world average).
Topic and keywords
Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- TiAl6V4
- titanium alloys
- self-lubricating coatings
- cemented carbide tools
- tool life
- turning
- tribological properties
- oxide phase formation
Work with this paper
Most-cited papers in Engineering
- A Closed‐form Equation for Predicting the Hydraulic Conductivity of Unsaturated SoilsMartinus Th. van Genuchten · Soil Science Society of America Journal · 1980 · 28,197 citations
- An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experimentsW. C. Oliver, George M. Pharr · Journal of materials research/Pratt's guide to venture capital sources · 1992 · 27,379 citations
- Digital communicationsOwen Bishop · Routledge eBooks · 2007 · 24,890 citations
- The empirical mode decomposition and the Hilbert spectrum for nonlinear and non-stationary time series analysisNorden Eh Huang, Zhengwei Shen, Steven R. Long and 6 more · Proceedings of the Royal Society A Mathematical Physical and Engineering Sciences · 1998 · 24,008 citations
- Numerical Heat Transfer and Fluid FlowSuhas V. Patankar · CRC Press eBooks · 2018 · 23,491 citations
Questions about this paper
How do I cite this paper in APA style?
Bobzin, K., Kalscheuer, C., Carlet, M., Stachowski, N., Hintze, W., Möller, C., & Ploog, P. (2022). Self-lubricating CrAlMoN high performance tool coatings for machining of TiAl6V4. Production Engineering, 17(3-4), 437–444. https://doi.org/10.1007/s11740-022-01161-8
How many times has this paper been cited?
5 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.
Is this paper free to read?
Yes. It is open access at Production Engineering: sign in and open the PDF from this page.
Who wrote this paper?
Kirsten Bobzin, C. Kalscheuer, M. Carlet, Nina Stachowski, Wolfgang Hintze, Carsten Möller, P. Ploog.
What is the DOI of this paper?
10.1007/s11740-022-01161-8, permanently at https://doi.org/10.1007/s11740-022-01161-8. Sign in and open it from this page.
Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.