Journal article · 2017 · Open access
Retained Austenite Transformation during Heat Treatment of a 5 Wt Pct Cr Cold Work Tool Steel
Metallurgical and Materials Transactions A, 48(11), 5233–5243 · Published 19 September 2017 · DOI 10.1007/s11661-017-4232-5
In brief
“Retained Austenite Transformation during Heat Treatment of a 5 Wt Pct Cr Cold Work Tool Steel” is a 2017 journal article by Arbab Rehan and 3 co-authors, published in Metallurgical and Materials Transactions A. OpenAlex counts 37 citations as of 22 November 2026. It is open access under a CC BY licence: the full text is free to read at Metallurgical and Materials Transactions A.
- Citations
- 37
- Most cited in
- 2024 (9)
- Field-weighted impact
- 0.73
- References
- 26
- Authors
- 4
Abstract
Retained austenite transformation was studied for a 5 wt pct Cr cold work tool steel tempered at 798 K and 873 K (525 °C and 600 °C) followed by cooling to room temperature. Tempering cycles with variations in holding times were conducted to observe the mechanisms involved. Phase transformations were studied with dilatometry, and the resulting microstructures were characterized with X-ray diffraction and scanning electron microscopy. Tempering treatments at 798 K (525 °C) resulted in retained austenite transformation to martensite on cooling. The martensite start (M s ) and martensite finish (M f ) temperatures increased with longer holding times at tempering temperature. At the same time, the lattice parameter of retained austenite decreased. Calculations from the M s temperatures and lattice parameters suggested that there was a decrease in carbon content of retained austenite as a result of precipitation of carbides prior to transformation. This was in agreement with the resulting microstructure and the contraction of the specimen during tempering, as observed by dilatometry. Tempering at 873 K (600 °C) resulted in precipitation of carbides in retained austenite followed by transformation to ferrite and carbides. This was further supported by the initial contraction and later expansion of the dilatometry specimen, the resulting microstructure, and the absence of any phase transformation on cooling from the tempering treatment. It was concluded that there are two mechanisms of retained austenite transformation occurring depending on tempering temperature and time. This was found useful in understanding the standard tempering treatment, and suggestions regarding alternative tempering treatments are discussed.
Cite this paper
Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.
APA 7
Rehan, A., Medvedeva, A., Svensson, L.-E., & Karlsson, L. (2017). Retained Austenite Transformation during Heat Treatment of a 5 Wt Pct Cr Cold Work Tool Steel. Metallurgical and Materials Transactions A, 48(11), 5233–5243. https://doi.org/10.1007/s11661-017-4232-5
MLA 9
Rehan, Arbab, et al. “Retained Austenite Transformation during Heat Treatment of a 5 Wt Pct Cr Cold Work Tool Steel.” Metallurgical and Materials Transactions A, vol. 48, no. 11, 2017, pp. 5233–5243. https://doi.org/10.1007/s11661-017-4232-5.
Chicago
Rehan, Arbab, Anna Medvedeva, Lars-Erik Svensson, and Leif Karlsson. 2017. “Retained Austenite Transformation during Heat Treatment of a 5 Wt Pct Cr Cold Work Tool Steel.” Metallurgical and Materials Transactions A 48 (11): 5233–5243. https://doi.org/10.1007/s11661-017-4232-5.
Harvard
Rehan, A. et al. (2017) ‘Retained Austenite Transformation during Heat Treatment of a 5 Wt Pct Cr Cold Work Tool Steel’, Metallurgical and Materials Transactions A, 48(11), pp. 5233–5243. doi:10.1007/s11661-017-4232-5.
IEEE
A. Rehan, A. Medvedeva, L.-E. Svensson, and L. Karlsson, “Retained Austenite Transformation during Heat Treatment of a 5 Wt Pct Cr Cold Work Tool Steel,” Metallurgical and Materials Transactions A, vol. 48, no. 11, pp. 5233–5243, 2017, doi: 10.1007/s11661-017-4232-5.
BibTeX
@article{rehan2017retained,
title = {{Retained Austenite Transformation during Heat Treatment of a 5 Wt Pct Cr Cold Work Tool Steel}},
author = {Rehan, Arbab and Medvedeva, Anna and Svensson, Lars-Erik and Karlsson, Leif},
journal = {Metallurgical and Materials Transactions A},
year = {2017},
volume = {48},
number = {11},
pages = {5233--5243},
doi = {10.1007/s11661-017-4232-5},
url = {https://doi.org/10.1007/s11661-017-4232-5}
}
Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)
Citations by year
| Year | Citations | Share of the best year |
|---|---|---|
| 2018 | 2 | |
| 2019 | 1 | |
| 2020 | 1 | |
| 2021 | 4 | |
| 2022 | 1 | |
| 2023 | 7 | |
| 2024 | 9 | |
| 2025 | 8 | |
| 2026 | 4 |
Its field-weighted citation impact is 0.73: it has been cited 0.73 times as often as the average work of the same field, type and year (1.00 is the world average).
Topic and keywords
Physical Sciences › Engineering › Mechanical Engineering › Microstructure and Mechanical Properties of Steels
- retained austenite transformation
- tempering
- martensitic transformation
- martensite start and finish temperatures
- lattice parameters
- carbide precipitation
- ferrite
- dilatometry
Work with this paper
Most-cited papers in Engineering
- A Closed‐form Equation for Predicting the Hydraulic Conductivity of Unsaturated SoilsMartinus Th. van Genuchten · Soil Science Society of America Journal · 1980 · 28,197 citations
- An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experimentsW. C. Oliver, George M. Pharr · Journal of materials research/Pratt's guide to venture capital sources · 1992 · 27,379 citations
- Digital communicationsOwen Bishop · Routledge eBooks · 2007 · 24,890 citations
- The empirical mode decomposition and the Hilbert spectrum for nonlinear and non-stationary time series analysisNorden Eh Huang, Zhengwei Shen, Steven R. Long and 6 more · Proceedings of the Royal Society A Mathematical Physical and Engineering Sciences · 1998 · 24,008 citations
- Numerical Heat Transfer and Fluid FlowSuhas V. Patankar · CRC Press eBooks · 2018 · 23,491 citations
Questions about this paper
How do I cite this paper in APA style?
Rehan, A., Medvedeva, A., Svensson, L.-E., & Karlsson, L. (2017). Retained Austenite Transformation during Heat Treatment of a 5 Wt Pct Cr Cold Work Tool Steel. Metallurgical and Materials Transactions A, 48(11), 5233–5243. https://doi.org/10.1007/s11661-017-4232-5
How many times has this paper been cited?
37 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.
Is this paper free to read?
Yes. It is open access at Metallurgical and Materials Transactions A: sign in and open the PDF from this page.
Who wrote this paper?
Arbab Rehan, Anna Medvedeva, Lars-Erik Svensson, Leif Karlsson.
What is the DOI of this paper?
10.1007/s11661-017-4232-5, permanently at https://doi.org/10.1007/s11661-017-4232-5. Sign in and open it from this page.
Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.