Conference paper · 2009 · Open access

Response of NiTi SMA wire electrically heated.

Claudio Zanotti, Piero Giuliani, Ausonio Tuissi, Sergio Arnaboldi, Riccardo Casati

European Symposium on Martensitic Transformations (ESOMAT) · Published 1 September 2009 · DOI 10.1051/esomat/200906037

Open PDFView at the publisherCite this paper

In brief

“Response of NiTi SMA wire electrically heated.” is a 2009 conference paper by Claudio Zanotti and 4 co-authors, published in European Symposium on Martensitic Transformations (ESOMAT). OpenAlex counts 25 citations as of 22 November 2026. It is open access: the full text is free to read at European Symposium on Martensitic Transformations (ESOMAT).

Citations
25
Most cited in
2019 (3)
Field-weighted impact
7.74
References
4
Authors
5

Abstract

In the present work an experimental-numerical approach is used to study the thermo-mechanical behaviour of NiTi wire for defining what parameters are the most important in actuator designing.Tests were carried out heating, by an electrical current, a wire having a diameter of 150 m, under constant stresses of 200 MPa.Data concerning strain, applied current and voltage are acquired during the tests by PC while wire temperature is recorded by thermographic system.The numerical code integrates the ordinary differential equation describing the volumetric wire heating and cooling transients assuming that the electrical power is the only external heating source.Temperature distribution in the wire is considered uniform and its change in time depends on wire specific heat, latent heat of the Martensitic-Austenitic transformation, free convection heat exchange coefficient and total emissivity of the surface wire.Comparisons between experimental and numerical results, obtained under different operating conditions, indicate that the wire heating rate mainly depends on the applied electrical power, latent heat of the Martensitic-Austenitic transformation, free convection heat exchange coefficient.In the case of the cooling transient, the capability to decrease the wire temperature to reach the ambient value is strongly effected, once the free convection heat exchange coefficient is defined, by the shape of the curve representing the Austenitic-Martensitic transformation.Simulations of the wire behaviour point out that the time necessary to obtain the maximum strain can be reduce to few ms if current of 10 A is used.Moreover, the strain dependence on time can be tailored by choosing the suitable heating transient.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Zanotti, C., Giuliani, P., Tuissi, A., Arnaboldi, S., & Casati, R. (2009). Response of NiTi SMA wire electrically heated. European Symposium on Martensitic Transformations (ESOMAT). https://doi.org/10.1051/esomat/200906037

MLA 9

Zanotti, Claudio, et al. “Response of NiTi SMA wire electrically heated.” European Symposium on Martensitic Transformations (ESOMAT), 2009. https://doi.org/10.1051/esomat/200906037.

Chicago

Zanotti, Claudio, Piero Giuliani, Ausonio Tuissi, Sergio Arnaboldi, and Riccardo Casati. 2009. “Response of NiTi SMA wire electrically heated.” European Symposium on Martensitic Transformations (ESOMAT). https://doi.org/10.1051/esomat/200906037.

Harvard

Zanotti, C. et al. (2009) ‘Response of NiTi SMA wire electrically heated.’, European Symposium on Martensitic Transformations (ESOMAT). doi:10.1051/esomat/200906037.

IEEE

C. Zanotti, P. Giuliani, A. Tuissi, S. Arnaboldi, and R. Casati, “Response of NiTi SMA wire electrically heated.,” European Symposium on Martensitic Transformations (ESOMAT), 2009, doi: 10.1051/esomat/200906037.

BibTeX

@inproceedings{zanotti2009response,
  title     = {{Response of NiTi SMA wire electrically heated.}},
  author    = {Zanotti, Claudio and Giuliani, Piero and Tuissi, Ausonio and Arnaboldi, Sergio and Casati, Riccardo},
  booktitle = {European Symposium on Martensitic Transformations (ESOMAT)},
  year      = {2009},
  doi       = {10.1051/esomat/200906037},
  url       = {https://doi.org/10.1051/esomat/200906037}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
201311
201422
201511
201933
202022
202122
202211
202333
202411
202633

Its field-weighted citation impact is 7.74: it has been cited 7.74 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Materials Science › Materials Chemistry › Shape Memory Alloy Transformations

  • NiTi wire
  • shape memory alloys
  • electric heating
  • thermomechanical behavior
  • latent heat
  • free convection heat transfer
  • strain response
  • actuator design

Work with this paper

Most-cited papers in Materials Science

All highly cited Materials Science papers

Questions about this paper

How do I cite this paper in APA style?

Zanotti, C., Giuliani, P., Tuissi, A., Arnaboldi, S., & Casati, R. (2009). Response of NiTi SMA wire electrically heated. European Symposium on Martensitic Transformations (ESOMAT). https://doi.org/10.1051/esomat/200906037

How many times has this paper been cited?

25 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at European Symposium on Martensitic Transformations (ESOMAT): sign in and open the PDF from this page.

Who wrote this paper?

Claudio Zanotti, Piero Giuliani, Ausonio Tuissi, Sergio Arnaboldi, Riccardo Casati.

What is the DOI of this paper?

10.1051/esomat/200906037, permanently at https://doi.org/10.1051/esomat/200906037. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.