Report · 1986 · Open access

Quantitative metallographic method for determining delta ferrite content in austenitic stainless steels. Final report

Gary Pressly

OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information) · Published 1 January 1986 · DOI 10.2172/6239282

Open PDFView at the publisherCite this paper

In brief

“Quantitative metallographic method for determining delta ferrite content in austenitic stainless steels. Final report” is a 1986 report by Gary Pressly, published in OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information). OpenAlex counts 0 citations as of 22 November 2026. It is open access: the full text is free to read at OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information).

Citations
0
References
3
Authors
1

Abstract

Delta ferrite is a magnetic form of iron and has a body centered cubic crystal structure. It is often present as a nonequilibrium phase in austenitic stainless steel welds, castings, and wrought materials. The ferrite content of austenitic stainless steel can directly affect its properties, especially weldability and formability. Therefore, it is highly desirable to be able to predict and/or measure the ferrite content accurately. Current magnetic ferrite measuring methods are not applicable when test materials are geometrically small (less than 2.54 mm thick and 6.35 mm wide). Therefore, a standard metallographic test method STM 00107-A was established to determine delta ferrite content in small weldments and base metals of austenitic stainless steel. This standard test method (STM 00107-A) was then performed on several exemplary metallographic specimens to illustrate its capabilities and applications. The results from the exemplary tests were compared and contrasted to metallographic manual point count measurements, Ferritescope measurements, and predicted values calculated from chemical analyses. By utilizing the manual metallographic point count data, an accuracy of +-16% and a precision of +-0.77% were determined for the standard test method. The comparison of Ferritescope data to standard test method revealed that the results obtained by the two methods are close at low (0 to 3%) ferrite contents and Ferritscope results are substantially greater at higher (6 to 10%) ferrite contents. The standard test method data compiled from the exemplary weld specimens was noted to be very similar to the predicted values calculated from chemical analyses. It was also shown that because the standard test method utilizes optics the morphology of the delta ferrite particles can be determined. This type of determination is possible only with metallographic methods.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Pressly, G. (1986). Quantitative metallographic method for determining delta ferrite content in austenitic stainless steels. Final report. OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information). https://doi.org/10.2172/6239282

MLA 9

Pressly, Gary. “Quantitative metallographic method for determining delta ferrite content in austenitic stainless steels. Final report.” OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information), 1986. https://doi.org/10.2172/6239282.

Chicago

Pressly, Gary. 1986. “Quantitative metallographic method for determining delta ferrite content in austenitic stainless steels. Final report.” OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information). https://doi.org/10.2172/6239282.

Harvard

Pressly, G. (1986) ‘Quantitative metallographic method for determining delta ferrite content in austenitic stainless steels. Final report’, OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information). doi:10.2172/6239282.

IEEE

G. Pressly, “Quantitative metallographic method for determining delta ferrite content in austenitic stainless steels. Final report,” OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information), 1986, doi: 10.2172/6239282.

BibTeX

@article{pressly1986quantitative,
  title     = {{Quantitative metallographic method for determining delta ferrite content in austenitic stainless steels. Final report}},
  author    = {Pressly, Gary},
  journal   = {OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information)},
  year      = {1986},
  doi       = {10.2172/6239282},
  url       = {https://doi.org/10.2172/6239282}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Microstructure and Mechanical Properties of Steels

  • delta ferrite
  • austenitic stainless steel
  • quantitative metallography
  • weldability
  • formability

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Pressly, G. (1986). Quantitative metallographic method for determining delta ferrite content in austenitic stainless steels. Final report. OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information). https://doi.org/10.2172/6239282

How many times has this paper been cited?

0 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information): sign in and open the PDF from this page.

Who wrote this paper?

Gary Pressly.

What is the DOI of this paper?

10.2172/6239282, permanently at https://doi.org/10.2172/6239282. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.