Conference paper · 2018 · Open access

Properties of TiN/CrN superlattice hard coatings deposited by reactive magnetron sputtering

Милко Ангелов, T. Cholakova, Lilyana Kolaklieva, Roumen Kakanakov, Vasiliy Chitanov

IOP Conference Series Materials Science and Engineering, 400, 032001 · Published 18 September 2018 · DOI 10.1088/1757-899x/400/3/032001

Open PDFView at the publisherCite this paper

In brief

“Properties of TiN/CrN superlattice hard coatings deposited by reactive magnetron sputtering” is a 2018 conference paper by Милко Ангелов and 4 co-authors, published in IOP Conference Series Materials Science and Engineering. OpenAlex counts 1 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at IOP Conference Series Materials Science and Engineering.

Citations
1
Most cited in
2020 (1)
Field-weighted impact
0.96
References
12
Authors
5

Abstract

Nanostructured TiN/CrN superlattice hard coatings were deposited using a reactive closed field unbalanced magnetron sputtering in the presence of additional anode for higher plasma ionisation degree at temperatures lower than 240°C. Coatings with three different bilayer periods (Λ) of 16 nm, 20 nm and 24 nm with applying a moderate substrate bias were obtained. The effect of bilayer period on the mechanical and tribological properties of the coatings was investigated by atomic force microscopy, nanoindentation, micro scratch and ball–on–disk wear tests. All the coatings possessed enhanced hardness, decreased coefficient of friction, improved adhesion and higher toughness in comparison with single-layer and gradient-composition hard coatings. The highest hardness value of about 30 GPa and elastic modulus of 360 GPa were measured for the coating with bilayer thickness of 24 nm. The friction coefficient against the diamond tip was within the range 0.2 for Λ = 20 nm to 0,208 for Λ = 16 nm. The calculated wear rates against 3/16 inch alumina ball were within the range from 1,045.10 −6 mm 3 /N.m for Λ = 24 nm to 1,955.10 −6 mm 3 /N.m for Λ = 16 nm. The static coefficient of friction μ SS against polished SS plate was μ SS = 0,268 for Λ = 24 nm, up to μ SS = 0,301 for Λ = 16 nm, as the reference TiN layer possesses μ SS = 0,218. The wetting angle of the coatings against deionised water was between 91° for Λ = 16 nm to 85° for Λ = 24 nm.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Ангелов, М., Cholakova, T., Kolaklieva, L., Kakanakov, R., & Chitanov, V. (2018). Properties of TiN/CrN superlattice hard coatings deposited by reactive magnetron sputtering. IOP Conference Series Materials Science and Engineering, 400, 032001. https://doi.org/10.1088/1757-899x/400/3/032001

MLA 9

Ангелов, Милко, et al. “Properties of TiN/CrN superlattice hard coatings deposited by reactive magnetron sputtering.” IOP Conference Series Materials Science and Engineering, vol. 400, 2018, p. 032001. https://doi.org/10.1088/1757-899x/400/3/032001.

Chicago

Ангелов, Милко, T. Cholakova, Lilyana Kolaklieva, Roumen Kakanakov, and Vasiliy Chitanov. 2018. “Properties of TiN/CrN superlattice hard coatings deposited by reactive magnetron sputtering.” IOP Conference Series Materials Science and Engineering 400: 032001. https://doi.org/10.1088/1757-899x/400/3/032001.

Harvard

Ангелов, М. et al. (2018) ‘Properties of TiN/CrN superlattice hard coatings deposited by reactive magnetron sputtering’, IOP Conference Series Materials Science and Engineering, 400, p. 032001. doi:10.1088/1757-899x/400/3/032001.

IEEE

М. Ангелов, T. Cholakova, L. Kolaklieva, R. Kakanakov, and V. Chitanov, “Properties of TiN/CrN superlattice hard coatings deposited by reactive magnetron sputtering,” IOP Conference Series Materials Science and Engineering, vol. 400, p. 032001, 2018, doi: 10.1088/1757-899x/400/3/032001.

BibTeX

@inproceedings{2018properties,
  title     = {{Properties of TiN/CrN superlattice hard coatings deposited by reactive magnetron sputtering}},
  author    = {Ангелов, Милко and Cholakova, T. and Kolaklieva, Lilyana and Kakanakov, Roumen and Chitanov, Vasiliy},
  booktitle = {IOP Conference Series Materials Science and Engineering},
  year      = {2018},
  volume    = {400},
  pages     = {032001},
  doi       = {10.1088/1757-899x/400/3/032001},
  url       = {https://doi.org/10.1088/1757-899x/400/3/032001}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics

  • bilayer period
  • reactive magnetron sputtering
  • unbalanced magnetron sputtering
  • low-temperature deposition
  • hardness
  • elastic modulus
  • tribological properties
  • friction coefficient

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Ангелов, М., Cholakova, T., Kolaklieva, L., Kakanakov, R., & Chitanov, V. (2018). Properties of TiN/CrN superlattice hard coatings deposited by reactive magnetron sputtering. IOP Conference Series Materials Science and Engineering, 400, 032001. https://doi.org/10.1088/1757-899x/400/3/032001

How many times has this paper been cited?

1 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at IOP Conference Series Materials Science and Engineering: sign in and open the PDF from this page.

Who wrote this paper?

Милко Ангелов, T. Cholakova, Lilyana Kolaklieva, Roumen Kakanakov, Vasiliy Chitanov.

What is the DOI of this paper?

10.1088/1757-899x/400/3/032001, permanently at https://doi.org/10.1088/1757-899x/400/3/032001. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.