Journal article · 2024 · Open access

Properties of Diamond-like Tungsten-Doped Carbon Coatings Lubricated with Cutting Fluid

Krystyna Radoń-Kobus, Monika Madej, Joanna Kowalczyk, Katarzyna Piotrowska

Coatings, 14(3), 342 · Published 13 March 2024 · DOI 10.3390/coatings14030342

Open full textCite this paper

In brief

“Properties of Diamond-like Tungsten-Doped Carbon Coatings Lubricated with Cutting Fluid” is a 2024 journal article by Krystyna Radoń-Kobus and 3 co-authors, published in Coatings. OpenAlex counts 9 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at Coatings.

Citations
9
Most cited in
2025 (6)
Field-weighted impact
1.17
References
27
Authors
4

Abstract

In this paper, the authors investigated the impact of DLC coatings doped with tungsten (a-C:H:W) coatings obtained using plasma-assisted physical vapor deposition (PVD) on the properties of the 100Cr6 steel. The results of the 100Cr6 steel specimens with and without the coating were compared. Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) analysis were used to observe the morphology of the coating surfaces and cross-sections and identify the elements in the coating composition. The contact angle of the investigated surfaces was measured with a tensiometer. Additionally, the effect of the coatings on the tribological properties of lubricated friction pairs was evaluated. Friction tests were performed on a ball-on-disc tribometer under lubrication with cutting fluid. The surface texture of the samples before and after the tribological tests was measured using a confocal profilometer. The results obtained from the tests and analysis allow for the conclusion that the use of DLC coatings a-C:H:W increases the hardness of 100Cr6 steel by three times. The values of the contact angles were indicative of surface hydrophilic characteristics. The tungsten-doped diamond-like coating under friction conditions reduced the coefficient of friction and wear. DLC coatings a-C:H:W lubricated with the cutting fluid improve the mechanical and tribological properties of 100Cr6 steel sliding surfaces under friction.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Radoń-Kobus, K., Madej, M., Kowalczyk, J., & Piotrowska, K. (2024). Properties of Diamond-like Tungsten-Doped Carbon Coatings Lubricated with Cutting Fluid. Coatings, 14(3), 342. https://doi.org/10.3390/coatings14030342

MLA 9

Radoń-Kobus, Krystyna, et al. “Properties of Diamond-like Tungsten-Doped Carbon Coatings Lubricated with Cutting Fluid.” Coatings, vol. 14, no. 3, 2024, p. 342. https://doi.org/10.3390/coatings14030342.

Chicago

Radoń-Kobus, Krystyna, Monika Madej, Joanna Kowalczyk, and Katarzyna Piotrowska. 2024. “Properties of Diamond-like Tungsten-Doped Carbon Coatings Lubricated with Cutting Fluid.” Coatings 14 (3): 342. https://doi.org/10.3390/coatings14030342.

Harvard

Radoń-Kobus, K. et al. (2024) ‘Properties of Diamond-like Tungsten-Doped Carbon Coatings Lubricated with Cutting Fluid’, Coatings, 14(3), p. 342. doi:10.3390/coatings14030342.

IEEE

K. Radoń-Kobus, M. Madej, J. Kowalczyk, and K. Piotrowska, “Properties of Diamond-like Tungsten-Doped Carbon Coatings Lubricated with Cutting Fluid,” Coatings, vol. 14, no. 3, p. 342, 2024, doi: 10.3390/coatings14030342.

BibTeX

@article{radonkobus2024properties,
  title     = {{Properties of Diamond-like Tungsten-Doped Carbon Coatings Lubricated with Cutting Fluid}},
  author    = {Radoń-Kobus, Krystyna and Madej, Monika and Kowalczyk, Joanna and Piotrowska, Katarzyna},
  journal   = {Coatings},
  year      = {2024},
  volume    = {14},
  number    = {3},
  pages     = {342},
  doi       = {10.3390/coatings14030342},
  url       = {https://doi.org/10.3390/coatings14030342}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
202411
202566
202622

Its field-weighted citation impact is 1.17: it has been cited 1.17 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics

  • 100Cr6 steel
  • tribological properties
  • friction coefficient
  • wear reduction
  • surface hardness
  • contact angle
  • surface hydrophilicity
  • surface texture

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Radoń-Kobus, K., Madej, M., Kowalczyk, J., & Piotrowska, K. (2024). Properties of Diamond-like Tungsten-Doped Carbon Coatings Lubricated with Cutting Fluid. Coatings, 14(3), 342. https://doi.org/10.3390/coatings14030342

How many times has this paper been cited?

9 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Coatings: sign in and open the full text from this page.

Who wrote this paper?

Krystyna Radoń-Kobus, Monika Madej, Joanna Kowalczyk, Katarzyna Piotrowska.

What is the DOI of this paper?

10.3390/coatings14030342, permanently at https://doi.org/10.3390/coatings14030342. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.