Journal article · 2017 · Open access

PHYSICAL AND MECHANICAL PROPERTIES AND WEAR RESISTANCE OF CRN/ALN SYSTEM COATINGS DEPOSITED BY MAGNETRON SPUTTERING

A. V. Aborkin, В. Е. Ваганов, М. И. Алымов, A.I. El'kin, И. М. Букарев

Powder Metallurgy аnd Functional Coatings, 65–74 · Published 1 January 2017 · DOI 10.17073/1997-308x-2017-3-65-74

Open PDFView at the publisherCite this paper

In brief

“PHYSICAL AND MECHANICAL PROPERTIES AND WEAR RESISTANCE OF CRN/ALN SYSTEM COATINGS DEPOSITED BY MAGNETRON SPUTTERING” is a 2017 journal article by A. V. Aborkin and 4 co-authors, published in Powder Metallurgy аnd Functional Coatings. OpenAlex counts 1 citations as of 17 November 2026, which puts it in the top 9% of works published in 2017 by citations. It is open access: the full text is free to read at Powder Metallurgy аnd Functional Coatings.

Citations
1
Most cited in
2026 (1)
References
21
Authors
5

Abstract

The paper presents the results of investigation of CrN/AlN system coatings obtained by magnetron-ion reactive sputtering. Coating versions with a periodic nanocomposite structure with a layer period L = 1,5÷3,2 nm and a relative Cr content in the Cr/(Al + Cr) coating range of 68–85 % are studied. It is found that the coatings have a dense morphology and a columnar grain structure, which is typical for them. For all the samples, diffraction maxima corresponding to the cubic lattice are observed, being a superposition of the two compositions of CrN and AlN coatings. No peaks corresponding to AlN with a hexagonal structure type are recorded. Neither CrAlN peaks are found, that means that no homogeneous coating is formed. Experimental studies of the microhardness, modulus of elasticity, plasticity index and wear resistance of coatings obtained under different spraying conditions are conducted. Measurements showed that the microhardness and modulus of elasticity of the coatings obtained vary between H = 32÷42 GPa and E = 350÷420 GPa, respectively. The maximum plasticity index value H/E = 0,115 is reached at L = 3,2 nm, which corresponds to the coating versions with the greatest hardness. However, the H/E = 0,1 values are also fairly high with a minimum layer period (L = 1,5 nm) and a high Cr content. Abrasive wear coefficients of the coatings obtained vary in the range kс = (2,0÷2,8)·10–13 m3/(N·m). The minimum values of wear are reached at the maximum period of coating layers, i.e. with the greatest hardness, which agrees well with the classical theory of wear. At the same time, high wear resistance is observed at a low L, which indicates a correlation of the values of H/E and kс. Based on the experimental data, a group of neural network models is built that establish the relationship between the deposition process mode parameters (current on magnetrons) with the elemental composition of coatings, as well as the period of coating layers and relative chromium content with the physical and mechanical properties and abrasion resistance of CrN/AlN coatings.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Aborkin, A. V., Ваганов, В. Е., Алымов, М. И., El'kin, A., & Букарев, И. М. (2017). PHYSICAL AND MECHANICAL PROPERTIES AND WEAR RESISTANCE OF CRN/ALN SYSTEM COATINGS DEPOSITED BY MAGNETRON SPUTTERING. Powder Metallurgy аnd Functional Coatings, 65–74. https://doi.org/10.17073/1997-308x-2017-3-65-74

MLA 9

Aborkin, A. V., et al. “PHYSICAL AND MECHANICAL PROPERTIES AND WEAR RESISTANCE OF CRN/ALN SYSTEM COATINGS DEPOSITED BY MAGNETRON SPUTTERING.” Powder Metallurgy аnd Functional Coatings, no. 3, 2017, pp. 65–74. https://doi.org/10.17073/1997-308x-2017-3-65-74.

Chicago

Aborkin, A. V., В. Е. Ваганов, М. И. Алымов, A.I. El'kin, and И. М. Букарев. 2017. “PHYSICAL AND MECHANICAL PROPERTIES AND WEAR RESISTANCE OF CRN/ALN SYSTEM COATINGS DEPOSITED BY MAGNETRON SPUTTERING.” Powder Metallurgy аnd Functional Coatings (3): 65–74. https://doi.org/10.17073/1997-308x-2017-3-65-74.

Harvard

Aborkin, A. V. et al. (2017) ‘PHYSICAL AND MECHANICAL PROPERTIES AND WEAR RESISTANCE OF CRN/ALN SYSTEM COATINGS DEPOSITED BY MAGNETRON SPUTTERING’, Powder Metallurgy аnd Functional Coatings, pp. 65–74. doi:10.17073/1997-308x-2017-3-65-74.

IEEE

A. V. Aborkin, В. Е. Ваганов, М. И. Алымов, A. El'kin, and И. М. Букарев, “PHYSICAL AND MECHANICAL PROPERTIES AND WEAR RESISTANCE OF CRN/ALN SYSTEM COATINGS DEPOSITED BY MAGNETRON SPUTTERING,” Powder Metallurgy аnd Functional Coatings, no. 3, pp. 65–74, 2017, doi: 10.17073/1997-308x-2017-3-65-74.

BibTeX

@article{aborkin2017physical,
  title     = {{PHYSICAL AND MECHANICAL PROPERTIES AND WEAR RESISTANCE OF CRN/ALN SYSTEM COATINGS DEPOSITED BY MAGNETRON SPUTTERING}},
  author    = {Aborkin, A. V. and Ваганов, В. Е. and Алымов, М. И. and El'kin, A.I. and Букарев, И. М.},
  journal   = {Powder Metallurgy аnd Functional Coatings},
  year      = {2017},
  number    = {3},
  pages     = {65--74},
  doi       = {10.17073/1997-308x-2017-3-65-74},
  url       = {https://doi.org/10.17073/1997-308x-2017-3-65-74}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics

  • nanocomposite coatings
  • magnetron sputtering
  • reactive sputtering
  • microhardness
  • elastic modulus
  • plasticity index
  • wear resistance
  • coating morphology

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Aborkin, A. V., Ваганов, В. Е., Алымов, М. И., El'kin, A., & Букарев, И. М. (2017). PHYSICAL AND MECHANICAL PROPERTIES AND WEAR RESISTANCE OF CRN/ALN SYSTEM COATINGS DEPOSITED BY MAGNETRON SPUTTERING. Powder Metallurgy аnd Functional Coatings, 65–74. https://doi.org/10.17073/1997-308x-2017-3-65-74

How many times has this paper been cited?

1 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Powder Metallurgy аnd Functional Coatings: sign in and open the PDF from this page.

Who wrote this paper?

A. V. Aborkin, В. Е. Ваганов, М. И. Алымов, A.I. El'kin, И. М. Букарев.

What is the DOI of this paper?

10.17073/1997-308x-2017-3-65-74, permanently at https://doi.org/10.17073/1997-308x-2017-3-65-74. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.