Dissertation · 2018 · Open access

Otimização do processo de soldagem robotizada tandem GMAW do aço ASTM A572 G50

Luis Felipe Scalet Rossini

LA Referencia (Red Federada de Repositorios Institucionales de Publicaciones Científicas) · Published 31 October 2018

Open full textCite this paper

In brief

“Otimização do processo de soldagem robotizada tandem GMAW do aço ASTM A572 G50” is a 2018 dissertation by Luis Felipe Scalet Rossini, published in LA Referencia (Red Federada de Repositorios Institucionales de Publicaciones Científicas). OpenAlex counts 0 citations as of 22 November 2026. It is open access: the full text is free to read at LA Referencia (Red Federada de Repositorios Institucionales de Publicaciones Científicas).

Citations
0
Authors
1

Abstract

The tandem welding process employs double wire feed in a single torch, \nproviding increased deposition rate and consequent reduction in process times. \nHowever, the process complexity increases because the correct combination of \nparameters is essential to avoid the occurrence of interference between the \nelectric arcs and defects, such as inadequate geometry, accentuated base \nmetal casting, which results in failures under service conditions. \nThe understanding of the TANDEM process and the optimization of the cycle \ntimes are the motivations of this work, having as a proposal to analyze the \npresence of defects and the changes in the microstructure and the mechanical \nstrength through the variation of the modes of metallic transfer, angulation of \nthe welding torch and consequent heat input variation. \nFor all parameter variations, ASTM A572 G50 structural steel test pieces \nwelded with ER70S-6 welding wire have been fabricated using robotic welding \nstations from a Multinational Company. The volume of the weldments has been \nthe same in all variations of parameters, allowing a comparative analysis of the \nquality of the joint and presence of defects. The probability of occurrence of \ndefects has been analyzed by the high-frequency acquisition of the values of \ncurrent, voltage and wire feed speed, while the penetration profile and the \ndimension of the heat affected zone have been examined through \nmacrographs. The analysis of the microstructure of the molten and heat \naffected areas has been carried out using an optical microscope, while for the \ndetermination of the strength, Vickers micro hardness profiles have been \nobtained. After different test conditions, the best combination of parameters was \nfound, where the master wire was parameterized in continuous current and the \nslave wire with pulsed metallic transfer, obtaining a 19,3% higher displacement \nspeed of the robot and no occurrence of anomalies in electrical arcs.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Rossini, L. F. S. (2018). Otimização do processo de soldagem robotizada tandem GMAW do aço ASTM A572 G50. LA Referencia (Red Federada de Repositorios Institucionales de Publicaciones Científicas). https://repositorio.ufscar.br/handle/20.500.14289/10905

MLA 9

Rossini, Luis Felipe Scalet. “Otimização do processo de soldagem robotizada tandem GMAW do aço ASTM A572 G50.” LA Referencia (Red Federada de Repositorios Institucionales de Publicaciones Científicas), 2018. https://repositorio.ufscar.br/handle/20.500.14289/10905.

Chicago

Rossini, Luis Felipe Scalet. 2018. “Otimização do processo de soldagem robotizada tandem GMAW do aço ASTM A572 G50.” LA Referencia (Red Federada de Repositorios Institucionales de Publicaciones Científicas). https://repositorio.ufscar.br/handle/20.500.14289/10905.

Harvard

Rossini, L. F. S. (2018) ‘Otimização do processo de soldagem robotizada tandem GMAW do aço ASTM A572 G50’, LA Referencia (Red Federada de Repositorios Institucionales de Publicaciones Científicas). Available at: https://repositorio.ufscar.br/handle/20.500.14289/10905.

IEEE

L. F. S. Rossini, “Otimização do processo de soldagem robotizada tandem GMAW do aço ASTM A572 G50,” LA Referencia (Red Federada de Repositorios Institucionales de Publicaciones Científicas), 2018.

BibTeX

@phdthesis{rossini2018otimiza,
  title     = {{Otimização do processo de soldagem robotizada tandem GMAW do aço ASTM A572 G50}},
  author    = {Rossini, Luis Felipe Scalet},
  year      = {2018},
  url       = {https://repositorio.ufscar.br/handle/20.500.14289/10905}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Welding Techniques and Residual Stresses

  • tandem welding
  • gas metal arc welding
  • robotic welding
  • welding parameter optimization
  • weld defects
  • heat-affected zone
  • weld penetration
  • microstructure

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Rossini, L. F. S. (2018). Otimização do processo de soldagem robotizada tandem GMAW do aço ASTM A572 G50. LA Referencia (Red Federada de Repositorios Institucionales de Publicaciones Científicas). https://repositorio.ufscar.br/handle/20.500.14289/10905

How many times has this paper been cited?

0 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at LA Referencia (Red Federada de Repositorios Institucionales de Publicaciones Científicas): sign in and open the full text from this page.

Who wrote this paper?

Luis Felipe Scalet Rossini.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.