Journal article · 2024 · Open access

On wear of TiAlN coated tools with and without NbN overlayer in machining titanium alloys

Rebecka Lindvall, Filip Lenrick, Jon M. Andersson, Rachid M’Saoubi, Volodymyr Bushlya

International Journal of Machine Tools and Manufacture, 198, 104148 · Published 21 March 2024 · DOI 10.1016/j.ijmachtools.2024.104148

Open full textCite this paper

In brief

“On wear of TiAlN coated tools with and without NbN overlayer in machining titanium alloys” is a 2024 journal article by Rebecka Lindvall and 4 co-authors, published in International Journal of Machine Tools and Manufacture. OpenAlex counts 46 citations as of 17 November 2026, which puts it in the top 2% of works published in 2024 by citations. It is open access under a CC BY licence: the full text is free to read at International Journal of Machine Tools and Manufacture.

Citations
46
Most cited in
2026 (25)
Field-weighted impact
5.67
References
62
Authors
5

Abstract

Finding a wear resistant coating for cemented carbide cutting tools in the machining of difficult to cut Ti alloys is a challenge due to their high strength and chemical reactivity. Tool manufacturers recommend physical vapor deposited (PVD) TixAl1-xN (x = 0.4–0.7), and an extra NbN overlayer has shown promising potential. This study explores wear mechanisms of PVD Ti0.45Al0.55N with and without NbN overlayer and its WC-Co substrate in machining Ti alloys. To achieve an accurate understanding of tool-chip-workpiece interaction and related wear mechanisms, several approaches were employed. Tests with controlled variation of cutting speeds were complemented by process freezing experiments using the quick stop method and imitational experiments of diffusion couples. Advanced microscopy techniques were employed for accurate detection of wear products and phenomena across length scale. Findings reveal that any new design of coatings for Ti machining must combine both high mechanical integrity and resistance to diffusional dissolution and oxidation. Observed diffusional loss of Al and N from the coating results in a TiN layer which is mechanically weaker than the original coating, while the NbN overlayer reduces the Al diffusion rate, but NbN is subjected to diffusional dissolution itself. On dissolution, Nb stabilizes β-Ti and thus facilitating loss of Al, but the observed formation of intermetallic Nb3Al at the NbN–Ti interface works as a diffusion barrier. However, brittle Nb3Al can be more easily removed during machining. It was found that the coating retains longest on the edge line and protects the tool edge from failure because substrate cemented carbide wears at a faster rate than the coating with outward diffusion of C from WC grains and Co binder.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Lindvall, R., Lenrick, F., Andersson, J. M., M’Saoubi, R., & Bushlya, V. (2024). On wear of TiAlN coated tools with and without NbN overlayer in machining titanium alloys. International Journal of Machine Tools and Manufacture, 198, 104148. https://doi.org/10.1016/j.ijmachtools.2024.104148

MLA 9

Lindvall, Rebecka, et al. “On wear of TiAlN coated tools with and without NbN overlayer in machining titanium alloys.” International Journal of Machine Tools and Manufacture, vol. 198, 2024, p. 104148. https://doi.org/10.1016/j.ijmachtools.2024.104148.

Chicago

Lindvall, Rebecka, Filip Lenrick, Jon M. Andersson, Rachid M’Saoubi, and Volodymyr Bushlya. 2024. “On wear of TiAlN coated tools with and without NbN overlayer in machining titanium alloys.” International Journal of Machine Tools and Manufacture 198: 104148. https://doi.org/10.1016/j.ijmachtools.2024.104148.

Harvard

Lindvall, R. et al. (2024) ‘On wear of TiAlN coated tools with and without NbN overlayer in machining titanium alloys’, International Journal of Machine Tools and Manufacture, 198, p. 104148. doi:10.1016/j.ijmachtools.2024.104148.

IEEE

R. Lindvall, F. Lenrick, J. M. Andersson, R. M’Saoubi, and V. Bushlya, “On wear of TiAlN coated tools with and without NbN overlayer in machining titanium alloys,” International Journal of Machine Tools and Manufacture, vol. 198, p. 104148, 2024, doi: 10.1016/j.ijmachtools.2024.104148.

BibTeX

@article{lindvall2024wear,
  title     = {{On wear of TiAlN coated tools with and without NbN overlayer in machining titanium alloys}},
  author    = {Lindvall, Rebecka and Lenrick, Filip and Andersson, Jon M. and M’Saoubi, Rachid and Bushlya, Volodymyr},
  journal   = {International Journal of Machine Tools and Manufacture},
  year      = {2024},
  volume    = {198},
  pages     = {104148},
  doi       = {10.1016/j.ijmachtools.2024.104148},
  url       = {https://doi.org/10.1016/j.ijmachtools.2024.104148}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
202466
20251515
20262525

Its field-weighted citation impact is 5.67: it has been cited 5.67 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization

  • TiAlN coating
  • cemented carbide cutting tools
  • titanium alloy machining
  • tool wear mechanisms
  • aluminum diffusion
  • diffusion barrier
  • oxidation resistance
  • WC-Co substrate

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Lindvall, R., Lenrick, F., Andersson, J. M., M’Saoubi, R., & Bushlya, V. (2024). On wear of TiAlN coated tools with and without NbN overlayer in machining titanium alloys. International Journal of Machine Tools and Manufacture, 198, 104148. https://doi.org/10.1016/j.ijmachtools.2024.104148

How many times has this paper been cited?

46 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at International Journal of Machine Tools and Manufacture: sign in and open the full text from this page.

Who wrote this paper?

Rebecka Lindvall, Filip Lenrick, Jon M. Andersson, Rachid M’Saoubi, Volodymyr Bushlya.

What is the DOI of this paper?

10.1016/j.ijmachtools.2024.104148, permanently at https://doi.org/10.1016/j.ijmachtools.2024.104148. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.