Journal article · 2018 · Open access

Oleic acid‐based poly(alkyl methacrylate) as bio‐based viscosity control additive for mineral and vegetable oils

Juliette Lomège, Claire Négrell, Jean‐Jacques Robin, Vincent Lapinte, Sylvain Caillol

Polymer Engineering and Science, 59(S1), E164–E170 · Published 10 August 2018 · DOI 10.1002/pen.24896

Open full textView at the publisherCite this paper

In brief

“Oleic acid‐based poly(alkyl methacrylate) as bio‐based viscosity control additive for mineral and vegetable oils” is a 2018 journal article by Juliette Lomège and 4 co-authors, published in Polymer Engineering and Science. OpenAlex counts 18 citations as of 17 November 2026. It is open access: the full text is free to read at HAL.

Citations
18
Most cited in
2018 (3)
Field-weighted impact
1.43
References
47
Authors
5

Abstract

This work described the design of an efficient oleic‐acid based viscosity control additive for lubricating oils as potential alternative to petroleum poly(alkyl)methacrylates (PAMAs) additives. Hence, Poly(2‐(methacryloyloxy)ethyl oleate) (PMAEO) was synthesized by free radical homopolymerization to afford a comb‐like polymer structure similar to common PAMAs. Then, in order to evaluate its efficiency as viscosity control additive, the resulting polymer was mixed at several concentrations from 1%wt to 10%wt with different oil compositions, including a mineral paraffinic oil (MPO) and an organic triglyceride oil (OTO). For all polymer‐solution blends, relative viscosities (RV) measurements showed that addition of PMAEO in MPO had a better contribution on oil viscosity at 100°C than at 20°C (RV = 1.16 at 40°C while RV = 1.25 for 3%wt of PMAEO in MPO). These results were attributed to the coil expansion of polymer chains with increasing temperature. Additionally, rheological studies showed that addition of 3%wt of PMAEO in MPO improved the MPO cold flow properties at −30°C by decreasing the required yield stress to put the oil in motion from 310 mPa to 42 mPa. These results are in total accordance with the common viscosimetric properties of PAMAs‐based viscosity control additives at low and high temperature in mineral oils. POLYM. ENG. SCI., 59:E164–E170, 2019. © 2018 Society of Plastics Engineers

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Lomège, J., Négrell, C., Robin, J., Lapinte, V., & Caillol, S. (2018). Oleic acid‐based poly(alkyl methacrylate) as bio‐based viscosity control additive for mineral and vegetable oils. Polymer Engineering and Science, 59(S1), E164–E170. https://doi.org/10.1002/pen.24896

MLA 9

Lomège, Juliette, et al. “Oleic acid‐based poly(alkyl methacrylate) as bio‐based viscosity control additive for mineral and vegetable oils.” Polymer Engineering and Science, vol. 59, no. S1, 2018, pp. E164–E170. https://doi.org/10.1002/pen.24896.

Chicago

Lomège, Juliette, Claire Négrell, Jean‐Jacques Robin, Vincent Lapinte, and Sylvain Caillol. 2018. “Oleic acid‐based poly(alkyl methacrylate) as bio‐based viscosity control additive for mineral and vegetable oils.” Polymer Engineering and Science 59 (S1): E164–E170. https://doi.org/10.1002/pen.24896.

Harvard

Lomège, J. et al. (2018) ‘Oleic acid‐based poly(alkyl methacrylate) as bio‐based viscosity control additive for mineral and vegetable oils’, Polymer Engineering and Science, 59(S1), pp. E164–E170. doi:10.1002/pen.24896.

IEEE

J. Lomège, C. Négrell, J. Robin, V. Lapinte, and S. Caillol, “Oleic acid‐based poly(alkyl methacrylate) as bio‐based viscosity control additive for mineral and vegetable oils,” Polymer Engineering and Science, vol. 59, no. S1, pp. E164–E170, 2018, doi: 10.1002/pen.24896.

BibTeX

@article{lomege2018oleic,
  title     = {{Oleic acid‐based poly(alkyl methacrylate) as bio‐based viscosity control additive for mineral and vegetable oils}},
  author    = {Lomège, Juliette and Négrell, Claire and Robin, Jean‐Jacques and Lapinte, Vincent and Caillol, Sylvain},
  journal   = {Polymer Engineering and Science},
  year      = {2018},
  volume    = {59},
  number    = {S1},
  pages     = {E164--E170},
  doi       = {10.1002/pen.24896},
  url       = {https://doi.org/10.1002/pen.24896}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
201833
201933
202011
202122
202233
202311
202411
202522
202622

Its field-weighted citation impact is 1.43: it has been cited 1.43 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Lubricants and Their Additives

  • oleic acid
  • poly(alkyl methacrylate)
  • lubricating oil
  • vegetable oils
  • triglyceride oils
  • comb polymers
  • viscosity ratio
  • cold flow properties

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Lomège, J., Négrell, C., Robin, J., Lapinte, V., & Caillol, S. (2018). Oleic acid‐based poly(alkyl methacrylate) as bio‐based viscosity control additive for mineral and vegetable oils. Polymer Engineering and Science, 59(S1), E164–E170. https://doi.org/10.1002/pen.24896

How many times has this paper been cited?

18 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at HAL: sign in and open the full text from this page.

Who wrote this paper?

Juliette Lomège, Claire Négrell, Jean‐Jacques Robin, Vincent Lapinte, Sylvain Caillol.

What is the DOI of this paper?

10.1002/pen.24896, permanently at https://doi.org/10.1002/pen.24896. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.