Journal article · 2026 · Open access

NiCrBSi-based coatings with WC-Co reinforcement and h-BN solid lubrication: microstructure and wear behavior after flame and HVOF spraying with flame fusing

Oleksandr Lypchanskyi, Bianca Preuß, Wolfgang Wisniewski, Maximilian Grimm, Thomas Grund, M. Schulz, W. Wietheger, Andreas Undisz, Thomas Lampke

Surface and Coatings Technology, 525, 133310 · Published 17 February 2026 · DOI 10.1016/j.surfcoat.2026.133310

Open full textCite this paper

In brief

“NiCrBSi-based coatings with WC-Co reinforcement and h-BN solid lubrication: microstructure and wear behavior after flame and HVOF spraying with flame fusing” is a 2026 journal article by Oleksandr Lypchanskyi and 8 co-authors, published in Surface and Coatings Technology. OpenAlex counts 2 citations as of 17 November 2026, which puts it in the top 5% of works published in 2026 by citations. It is open access under a CC BY licence: the full text is free to read at Surface and Coatings Technology.

Citations
2
Most cited in
2026 (2)
Field-weighted impact
2.90
References
83
Authors
9

Abstract

Thermally sprayed self-fluxing NiCrBSi-based coatings modified with WC-Co as a reinforcing phase and h-BN as a solid lubricant were produced using conventional flame spraying and high-velocity oxygen-fuel (HVOF) spraying, followed by flame fusing to improve densification and interfacial bonding. The influence of the spraying energy input, coating composition, and post-deposition flame fusing on the microstructural evolution and tribological performance at room temperature (RT) and 400 °C are investigated. Novel insights into the stabilization and distribution of carbides (Cr 7 C 3 ), borides (CrB) and Ni-based intermetallic phases (Ni 3 B, Ni 31 Si 12 ), as well as the persistence, partial degradation, and anchoring behavior of h-BN particles are provided. Flame spraying leads to thicker coatings with splat-related inhomogeneities, whereas HVOF spraying produces thinner, denser coatings with finer microstructures. Flame fusing substantially modifies both coating series by eliminating splat boundaries, inducing partial remelting, and promoting the formation of eutectic structures and a dendrite-containing fusion zone that includes Mo 6 Ni 6 C. Fretting wear tests under severe reciprocating conditions at RT and 400 °C reveal a strong dependence of wear behavior on coating composition, microstructure, and processing history. Flame fusing the HVOF coatings induces a partial decomposition of WC and the formation of brittle W 2 CoB 2 , resulting in increased microcracking and higher wear rates of ~0.7–1.5 × 10 −4 mm 3 /Nm at RT. However, the wear rates at RT and 400 °C remain comparable due to embrittlement and the development of oxide-based tribolayers. Analyses of the worn surfaces indicate a temperature-dependent shift in the dominant wear mechanisms—from adhesive wear and surface fatigue at RT to mixed abrasive–adhesive wear combined with tribochemical oxidation at 400 °C, where oxidized tribolayers and plasticized splats facilitate lubrication and coefficient of friction (COF) stabilization. These findings provide new insights into the role of microstructural heterogeneities, WC decomposition, dendrite-containing fusion zones, and h-BN particle behavior in governing the tribological response of thermally sprayed coatings, outlining a pathway toward advanced coating solutions for high-performance valve components and related tribological applications. • h-BN and WC-Co particles exhibit distinct stability and interfacial bonding. • Flame fusing enhances densification and promotes metallurgical inter-splat bonding. • Partially degraded h-BN causes debris and reduces lubrication efficiency. • Flame fusing can form dendritic fusion zones and induces WC decomposition. • Process–structure design can improve wear resistance for high-temperature service.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Lypchanskyi, O., Preuß, B., Wisniewski, W., Grimm, M., Grund, T., Schulz, M., Wietheger, W., Undisz, A., & Lampke, T. (2026). NiCrBSi-based coatings with WC-Co reinforcement and h-BN solid lubrication: microstructure and wear behavior after flame and HVOF spraying with flame fusing. Surface and Coatings Technology, 525, 133310. https://doi.org/10.1016/j.surfcoat.2026.133310

MLA 9

Lypchanskyi, Oleksandr, et al. “NiCrBSi-based coatings with WC-Co reinforcement and h-BN solid lubrication: microstructure and wear behavior after flame and HVOF spraying with flame fusing.” Surface and Coatings Technology, vol. 525, 2026, p. 133310. https://doi.org/10.1016/j.surfcoat.2026.133310.

Chicago

Lypchanskyi, Oleksandr, Bianca Preuß, Wolfgang Wisniewski, Maximilian Grimm, Thomas Grund, M. Schulz, W. Wietheger, Andreas Undisz, and Thomas Lampke. 2026. “NiCrBSi-based coatings with WC-Co reinforcement and h-BN solid lubrication: microstructure and wear behavior after flame and HVOF spraying with flame fusing.” Surface and Coatings Technology 525: 133310. https://doi.org/10.1016/j.surfcoat.2026.133310.

Harvard

Lypchanskyi, O. et al. (2026) ‘NiCrBSi-based coatings with WC-Co reinforcement and h-BN solid lubrication: microstructure and wear behavior after flame and HVOF spraying with flame fusing’, Surface and Coatings Technology, 525, p. 133310. doi:10.1016/j.surfcoat.2026.133310.

IEEE

O. Lypchanskyi et al., “NiCrBSi-based coatings with WC-Co reinforcement and h-BN solid lubrication: microstructure and wear behavior after flame and HVOF spraying with flame fusing,” Surface and Coatings Technology, vol. 525, p. 133310, 2026, doi: 10.1016/j.surfcoat.2026.133310.

BibTeX

@article{lypchanskyi2026nicrbsi,
  title     = {{NiCrBSi-based coatings with WC-Co reinforcement and h-BN solid lubrication: microstructure and wear behavior after flame and HVOF spraying with flame fusing}},
  author    = {Lypchanskyi, Oleksandr and Preuß, Bianca and Wisniewski, Wolfgang and Grimm, Maximilian and Grund, Thomas and Schulz, M. and Wietheger, W. and Undisz, Andreas and Lampke, Thomas},
  journal   = {Surface and Coatings Technology},
  year      = {2026},
  volume    = {525},
  pages     = {133310},
  doi       = {10.1016/j.surfcoat.2026.133310},
  url       = {https://doi.org/10.1016/j.surfcoat.2026.133310}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Materials Science › Surfaces, Coatings and Films › High-Temperature Coating Behaviors

  • NiCrBSi coatings
  • hexagonal boron nitride
  • solid lubrication
  • flame spraying
  • HVOF spraying
  • wear behavior
  • tribolayer
  • Cr7C3 carbide

Work with this paper

Most-cited papers in Materials Science

All highly cited Materials Science papers

Questions about this paper

How do I cite this paper in APA style?

Lypchanskyi, O., Preuß, B., Wisniewski, W., Grimm, M., Grund, T., Schulz, M., Wietheger, W., Undisz, A., & Lampke, T. (2026). NiCrBSi-based coatings with WC-Co reinforcement and h-BN solid lubrication: microstructure and wear behavior after flame and HVOF spraying with flame fusing. Surface and Coatings Technology, 525, 133310. https://doi.org/10.1016/j.surfcoat.2026.133310

How many times has this paper been cited?

2 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Surface and Coatings Technology: sign in and open the full text from this page.

Who wrote this paper?

Oleksandr Lypchanskyi, Bianca Preuß, Wolfgang Wisniewski, Maximilian Grimm, Thomas Grund, M. Schulz, W. Wietheger, Andreas Undisz, Thomas Lampke.

What is the DOI of this paper?

10.1016/j.surfcoat.2026.133310, permanently at https://doi.org/10.1016/j.surfcoat.2026.133310. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.