Dissertation · 2021 · Open access

Nanomechanical Characterisation of Diamond-Like Carbon Coatings for Tribological Performance

Samuel James McMaster

White Rose eTheses Online (University of Leeds, The University of Sheffield, University of York) · Published 1 January 2021 · DOI 10.13140/rg.2.2.13315.02083

Open full textView at the publisherCite this paper

In brief

“Nanomechanical Characterisation of Diamond-Like Carbon Coatings for Tribological Performance” is a 2021 dissertation by Samuel James McMaster, published in White Rose eTheses Online (University of Leeds, The University of Sheffield, University of York). OpenAlex counts 4 citations as of 17 November 2026. It is open access under a CC BY-NC licence: the full text is free to read at Pure (Coventry University).

Citations
4
Most cited in
2021 (1)
Authors
1

Abstract

Diamond-like carbon (DLC) coatings are becoming increasingly popular in the automotive industry due to their high hardness, resistance to wear and low friction coefficient. Additionally, they have seen more recent use in the oil and gas industry as protective coatings for flow control devices such as gate and ball valves. They can suffer from poor adhesion at high loads and impact stresses. Well characterised coatings will enable the relationship between mechanical properties and tribological behaviour under different wear regimes to be studied. To this end, three DLC variants have been produced; amorphous hydrogenated carbon, silicon-doped amorphous hydrogenated carbon and tungsten-doped amorphous hydrogenated carbon (a-C:H, Si:a-C:H and a-C:H:W) on two different substrates (316L stainless steel and hardened M2 tool steel) using the Hauzer Flexicoat 850 system located at the University of Leeds. Total thickness of the coating was varied from 1–5 µm. For the a-C:H coating, the substrate roughness was varied between 0.01 and 0.08 µm Ra. A Cr + WC/W-C:H interlayer is present in all coatings to aid adhesion to the substrate. Mechanical characterisation has been performed using nanoindentation on the Micro Materials Nanotest Platform using a partial loading technique. Structural characterisation of the DLC was performed using Raman spectroscopy to measure graphitisation and disorder and electron energy loss spectroscopy (EELS) to determine sp2/sp3 ratio respectively. Throughout the testing, scanning electron microscopy (SEM) has been used to observe the deformation and failure mechanisms of the coatings. Following this nano-scale fatigue resistance of the coatings was measured by comparing nano and micro-scale impact testing with solid particle erosion. Erosion testing was performed with a bespoke air powered flow system. Depth reached and relative depth increase with load during impact testing was compared with the amount of substrate visible (measured using optical pixel threshold method) after time-steps of erosion testing. For this application it was found that a lower H/E ratio and less severe cracking is beneficial as seen with a-C:H:W. Cross-section focused ion beam scanning electron microscopy was used to observe the coating-interlayer cracking phenomena. Nano-scratch testing was performed to investigate the interfacial contribution to friction of various probe radii (4:5 µm, 8 µm, 72 µm and 170 µm) compared with one DLC coating, a-C:H on 316L stainless steel. All the DLC coatings were subsequently tested using the 4.5 µm probe to observe critical load failures of each coating architecture. Subcritical load scratch tests were also performed to investigate the number of passes to failure. Fretting tests have been performed on two length scales. Larger length-scale utilised a 5 mm radius…

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

McMaster, S. J. (2021). Nanomechanical Characterisation of Diamond-Like Carbon Coatings for Tribological Performance. White Rose eTheses Online (University of Leeds, The University of Sheffield, University of York). https://doi.org/10.13140/rg.2.2.13315.02083

MLA 9

McMaster, Samuel James. “Nanomechanical Characterisation of Diamond-Like Carbon Coatings for Tribological Performance.” White Rose eTheses Online (University of Leeds, The University of Sheffield, University of York), 2021. https://doi.org/10.13140/rg.2.2.13315.02083.

Chicago

McMaster, Samuel James. 2021. “Nanomechanical Characterisation of Diamond-Like Carbon Coatings for Tribological Performance.” White Rose eTheses Online (University of Leeds, The University of Sheffield, University of York). https://doi.org/10.13140/rg.2.2.13315.02083.

Harvard

McMaster, S. J. (2021) ‘Nanomechanical Characterisation of Diamond-Like Carbon Coatings for Tribological Performance’, White Rose eTheses Online (University of Leeds, The University of Sheffield, University of York). doi:10.13140/rg.2.2.13315.02083.

IEEE

S. J. McMaster, “Nanomechanical Characterisation of Diamond-Like Carbon Coatings for Tribological Performance,” White Rose eTheses Online (University of Leeds, The University of Sheffield, University of York), 2021, doi: 10.13140/rg.2.2.13315.02083.

BibTeX

@phdthesis{mcmaster2021nanomechanical,
  title     = {{Nanomechanical Characterisation of Diamond-Like Carbon Coatings for Tribological Performance}},
  author    = {McMaster, Samuel James},
  year      = {2021},
  doi       = {10.13140/rg.2.2.13315.02083},
  url       = {https://doi.org/10.13140/rg.2.2.13315.02083}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
202111
202411
202511
202611

Topic and keywords

Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics

  • diamond-like carbon films
  • hydrogenated amorphous carbon
  • silicon doping
  • tungsten doping
  • tribological properties
  • nanoindentation
  • solid particle erosion
  • impact testing

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

McMaster, S. J. (2021). Nanomechanical Characterisation of Diamond-Like Carbon Coatings for Tribological Performance. White Rose eTheses Online (University of Leeds, The University of Sheffield, University of York). https://doi.org/10.13140/rg.2.2.13315.02083

How many times has this paper been cited?

4 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Pure (Coventry University): sign in and open the full text from this page.

Who wrote this paper?

Samuel James McMaster.

What is the DOI of this paper?

10.13140/rg.2.2.13315.02083, permanently at https://doi.org/10.13140/rg.2.2.13315.02083. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.