Journal article · 2003 · Open access

Microstructure, mechanical properties and cutting performance of superhard (Ti,Si,Al)N nanocomposite films grown by d.c. reactive magnetron sputtering

S. Carvalho, E. Ribeiro, L. Rebouta, Carlos José Tavares, João Pedro Mendonça, António Monteiro, N.J.M. Carvalho, J. Th. M. De Hosson, A. Cavaleiro

Surface and Coatings Technology, 177-178, 459–468 · Published 22 October 2003 · DOI 10.1016/j.surfcoat.2003.08.056

Open PDFView at the publisherCite this paper

In brief

“Microstructure, mechanical properties and cutting performance of superhard (Ti,Si,Al)N nanocomposite films grown by d.c. reactive magnetron sputtering” is a 2003 journal article by S. Carvalho and 8 co-authors, published in Surface and Coatings Technology. OpenAlex counts 74 citations as of 17 November 2026. It is open access: the full text is free to read at Surface and Coatings Technology.

Citations
74
Most cited in
2017 (8)
Field-weighted impact
2.65
References
26
Authors
9

Abstract

This paper reports on the optimization of coating properties to improve the performance of tools in severe cutting conditions. Tungsten carbide tools coated with (Ti,Si,Al)N films deposited by d.c. reactive magnetron sputtering have been investigated. The structure and the hardness of the coated samples were analyzed by X-ray diffraction (XRD) and depth-sensing indentation, respectively. XRD results revealed a structure indexed to fcc TiN. The tool life and tool failure modes were examined for various cutting conditions. A promising wear performance of the (Ti,Si,Al)N coatings was confirmed by scanning electron microscopy observations complemented with energy dispersive X-ray spectrometry analysis. At higher cutting speed (200 m/min) it seems that after turning 15 min the cutting performance of (Ti,Si,Al)N coated tools is better than that presented by the commercial multilayer coating (TiCN/Al2O3/TiN)—which was used as a reference. Also regarding the final surface finish of the steel workpiece, the (Ti,Si,Al)N coatings outperformed the commercial tool, considering that the roughness of the workpiece is smaller in the former case (4 μm) than that measured in the latter one (12 μm).

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Carvalho, S., Ribeiro, E., Rebouta, L., Tavares, C. J., Mendonça, J. P., Monteiro, A., Carvalho, N., De Hosson, J. T. M., & Cavaleiro, A. (2003). Microstructure, mechanical properties and cutting performance of superhard (Ti,Si,Al)N nanocomposite films grown by d.c. reactive magnetron sputtering. Surface and Coatings Technology, 177-178, 459–468. https://doi.org/10.1016/j.surfcoat.2003.08.056

MLA 9

Carvalho, S., et al. “Microstructure, mechanical properties and cutting performance of superhard (Ti,Si,Al)N nanocomposite films grown by d.c. reactive magnetron sputtering.” Surface and Coatings Technology, vol. 177-178, 2003, pp. 459–468. https://doi.org/10.1016/j.surfcoat.2003.08.056.

Chicago

Carvalho, S., E. Ribeiro, L. Rebouta, Carlos José Tavares, João Pedro Mendonça, António Monteiro, N.J.M. Carvalho, J. Th. M. De Hosson, and A. Cavaleiro. 2003. “Microstructure, mechanical properties and cutting performance of superhard (Ti,Si,Al)N nanocomposite films grown by d.c. reactive magnetron sputtering.” Surface and Coatings Technology 177-178: 459–468. https://doi.org/10.1016/j.surfcoat.2003.08.056.

Harvard

Carvalho, S. et al. (2003) ‘Microstructure, mechanical properties and cutting performance of superhard (Ti,Si,Al)N nanocomposite films grown by d.c. reactive magnetron sputtering’, Surface and Coatings Technology, 177-178, pp. 459–468. doi:10.1016/j.surfcoat.2003.08.056.

IEEE

S. Carvalho et al., “Microstructure, mechanical properties and cutting performance of superhard (Ti,Si,Al)N nanocomposite films grown by d.c. reactive magnetron sputtering,” Surface and Coatings Technology, vol. 177-178, pp. 459–468, 2003, doi: 10.1016/j.surfcoat.2003.08.056.

BibTeX

@article{carvalho2003microstructure,
  title     = {{Microstructure, mechanical properties and cutting performance of superhard (Ti,Si,Al)N nanocomposite films grown by d.c. reactive magnetron sputtering}},
  author    = {Carvalho, S. and Ribeiro, E. and Rebouta, L. and Tavares, Carlos José and Mendonça, João Pedro and Monteiro, António and Carvalho, N.J.M. and De Hosson, J. Th. M. and Cavaleiro, A.},
  journal   = {Surface and Coatings Technology},
  year      = {2003},
  volume    = {177-178},
  pages     = {459--468},
  doi       = {10.1016/j.surfcoat.2003.08.056},
  url       = {https://doi.org/10.1016/j.surfcoat.2003.08.056}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
201788
201855
201922
202033
202111
202222
202311
202411
202522
202622

Its field-weighted citation impact is 2.65: it has been cited 2.65 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics

  • superhard coatings
  • tungsten carbide tools
  • cutting performance
  • tool life
  • wear behavior
  • surface finish
  • cutting speed
  • coating microstructure

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Carvalho, S., Ribeiro, E., Rebouta, L., Tavares, C. J., Mendonça, J. P., Monteiro, A., Carvalho, N., De Hosson, J. T. M., & Cavaleiro, A. (2003). Microstructure, mechanical properties and cutting performance of superhard (Ti,Si,Al)N nanocomposite films grown by d.c. reactive magnetron sputtering. Surface and Coatings Technology, 177-178, 459–468. https://doi.org/10.1016/j.surfcoat.2003.08.056

How many times has this paper been cited?

74 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Surface and Coatings Technology: sign in and open the PDF from this page.

Who wrote this paper?

S. Carvalho, E. Ribeiro, L. Rebouta, Carlos José Tavares, João Pedro Mendonça, António Monteiro, N.J.M. Carvalho, J. Th. M. De Hosson, A. Cavaleiro.

What is the DOI of this paper?

10.1016/j.surfcoat.2003.08.056, permanently at https://doi.org/10.1016/j.surfcoat.2003.08.056. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.