Journal article · 2010 · Open access
Microstructure and Reciprocating Sliding Tribological Performance of Micro-Arc Oxidation Coating Prepared on Al-Si Alloy
Advanced materials research, 97-101, 1518–1526 · Published 1 March 2010 · DOI 10.4028/www.scientific.net/amr.97-101.1518
In brief
“Microstructure and Reciprocating Sliding Tribological Performance of Micro-Arc Oxidation Coating Prepared on Al-Si Alloy” is a 2010 journal article by Xiu Zhou Lin and 4 co-authors, published in Advanced materials research. OpenAlex counts 2 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at Advanced materials research.
- Citations
- 2
- Most cited in
- 2019 (1)
- References
- 21
- Authors
- 5
Abstract
Micro-arc oxidation coatings were prepared on Al-Si alloys surface by using a self-made micro-arc oxidation equipment. Its characterizations were systematically detected by Vickers hardness tester, profilometer, scanning electron microscope (SEM), energy dispersive X-ray spectrum (EDX), X-ray diffractometer (XRD) and X-ray photoelectron spectroscopy (XPS). Reciprocating sliding tribological tests without lubricant of the micro-arc oxidation coating and its substrate alloy have been carried out under normal load of 5 N and displacement amplitudes of 2 mm. Dynamic analyses in combination with microscopic examinations were performed in detail through optical microscope (OM), SEM and EDX. The experimental results indicated that the MAO coating, with rough surface, high hardness and typical porous ceramic structure, is mainly consist of Al2O3, SiO2 and Al2SiO5 phases. The elementary substance Si and Al are not presented nearly on surface of coatings since the alloy is oxidated adequately during the micro arc oxidation process. Three stages can be observed in the friction coefficient curves both for the MAO coating and its substrate. The COF of the substrate was very low in initial stage, then a rapid ascend to a higher level and fluctuated in a larger range. But for the MAO coating, since its higher hardness and rough surface, the COF was higher than its substrate in initial stage. After a gradually ascent stage, the COF reached a steady state with a small range fluctuation and higher values. The wear mechanism for Al-Si alloy was main adhesive wear, abrasive wear, delamination and slight oxidative wear. After the micro-arc oxidation, the wear resistance of Al-Si alloy was greatly improved, and the wear mechanism of the MAO coating was the combination of delamination, abrasive wear, slight oxidative wear and some material transferred from the ball specimen.
Cite this paper
Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.
APA 7
Lin, X. Z., Zhu, M., Cai, Z. B., Zheng, J., & Peng, J. F. (2010). Microstructure and Reciprocating Sliding Tribological Performance of Micro-Arc Oxidation Coating Prepared on Al-Si Alloy. Advanced materials research, 97-101, 1518–1526. https://doi.org/10.4028/www.scientific.net/amr.97-101.1518
MLA 9
Lin, Xiu Zhou, et al. “Microstructure and Reciprocating Sliding Tribological Performance of Micro-Arc Oxidation Coating Prepared on Al-Si Alloy.” Advanced materials research, vol. 97-101, 2010, pp. 1518–1526. https://doi.org/10.4028/www.scientific.net/amr.97-101.1518.
Chicago
Lin, Xiu Zhou, Min Zhu, Zhen Bing Cai, Jianfeng Zheng, and Jin Fang Peng. 2010. “Microstructure and Reciprocating Sliding Tribological Performance of Micro-Arc Oxidation Coating Prepared on Al-Si Alloy.” Advanced materials research 97-101: 1518–1526. https://doi.org/10.4028/www.scientific.net/amr.97-101.1518.
Harvard
Lin, X. Z. et al. (2010) ‘Microstructure and Reciprocating Sliding Tribological Performance of Micro-Arc Oxidation Coating Prepared on Al-Si Alloy’, Advanced materials research, 97-101, pp. 1518–1526. doi:10.4028/www.scientific.net/amr.97-101.1518.
IEEE
X. Z. Lin, M. Zhu, Z. B. Cai, J. Zheng, and J. F. Peng, “Microstructure and Reciprocating Sliding Tribological Performance of Micro-Arc Oxidation Coating Prepared on Al-Si Alloy,” Advanced materials research, vol. 97-101, pp. 1518–1526, 2010, doi: 10.4028/www.scientific.net/amr.97-101.1518.
BibTeX
@article{lin2010microstructure,
title = {{Microstructure and Reciprocating Sliding Tribological Performance of Micro-Arc Oxidation Coating Prepared on Al-Si Alloy}},
author = {Lin, Xiu Zhou and Zhu, Min and Cai, Zhen Bing and Zheng, Jianfeng and Peng, Jin Fang},
journal = {Advanced materials research},
year = {2010},
volume = {97-101},
pages = {1518--1526},
doi = {10.4028/www.scientific.net/amr.97-101.1518},
url = {https://doi.org/10.4028/www.scientific.net/amr.97-101.1518}
}
Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)
Topic and keywords
Physical Sciences › Engineering › Mechanical Engineering › Surface Treatment and Coatings
- plasma electrolytic oxidation
- Al-Si alloys
- reciprocating sliding wear
- tribological properties
- friction coefficient
- wear mechanisms
- ceramic coatings
- Vickers hardness
Work with this paper
Most-cited papers in Engineering
- A Closed‐form Equation for Predicting the Hydraulic Conductivity of Unsaturated SoilsMartinus Th. van Genuchten · Soil Science Society of America Journal · 1980 · 28,197 citations
- An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experimentsW. C. Oliver, George M. Pharr · Journal of materials research/Pratt's guide to venture capital sources · 1992 · 27,379 citations
- Digital communicationsOwen Bishop · Routledge eBooks · 2007 · 24,890 citations
- The empirical mode decomposition and the Hilbert spectrum for nonlinear and non-stationary time series analysisNorden Eh Huang, Zhengwei Shen, Steven R. Long and 6 more · Proceedings of the Royal Society A Mathematical Physical and Engineering Sciences · 1998 · 24,008 citations
- Numerical Heat Transfer and Fluid FlowSuhas V. Patankar · CRC Press eBooks · 2018 · 23,491 citations
Questions about this paper
How do I cite this paper in APA style?
Lin, X. Z., Zhu, M., Cai, Z. B., Zheng, J., & Peng, J. F. (2010). Microstructure and Reciprocating Sliding Tribological Performance of Micro-Arc Oxidation Coating Prepared on Al-Si Alloy. Advanced materials research, 97-101, 1518–1526. https://doi.org/10.4028/www.scientific.net/amr.97-101.1518
How many times has this paper been cited?
2 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.
Is this paper free to read?
Yes. It is open access at Advanced materials research: sign in and open the full text from this page.
Who wrote this paper?
Xiu Zhou Lin, Min Zhu, Zhen Bing Cai, Jianfeng Zheng, Jin Fang Peng.
What is the DOI of this paper?
10.4028/www.scientific.net/amr.97-101.1518, permanently at https://doi.org/10.4028/www.scientific.net/amr.97-101.1518. Sign in and open it from this page.
Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.