Journal article · 2014 · Open access
Micro-texturing of DLC Thin Film Coatings and its Tribological Performance Under Dry Sliding Friction for Microforming Operation
Procedia Engineering, 81, 1884–1889 · Published 1 January 2014 · DOI 10.1016/j.proeng.2014.10.251
In brief
“Micro-texturing of DLC Thin Film Coatings and its Tribological Performance Under Dry Sliding Friction for Microforming Operation” is a 2014 journal article by Tetsuhide Shimizu and 2 co-authors, published in Procedia Engineering. OpenAlex counts 33 citations as of 17 November 2026. It is open access under a CC BY-NC-ND licence: the full text is free to read at Procedia Engineering.
- Citations
- 33
- Most cited in
- 2020 (7)
- Field-weighted impact
- 2.44
- References
- 14
- Authors
- 3
Abstract
As an approach to enhance the tribological performance of diamond like carbon (DLC) coating films for dry microforming operations, the present study applied the micro-textured structures to the DLC films. Micro-texturing was realized by using stainless steel wire mesh as a masking during the ionized physical vapor deposition (I-PVD) of DLC films. Tribological performance of fabricated micro-textured structures with a width of 40 and 80 μm and an interval of 30 and 40 μm were evaluated by the ball-on-disk type friction tester. To simulate the severe contact state of dry microforming operation, normal pressure of 1.2 GPa was applied for 100,000 times rotations under unlubricated condition. As results, the micro-textured DLC films with structure size of 40 μm showed the excellent stable variation with relatively low coefficient of friction (COF) of μ = 0.01-0.06, while the conventional non-textured DLC films showed the significantly large deviation with high COF of μ > 0.25. In comparison between the different micro-texture sizes, the smaller structure size of 40 μm showed the lower COF than that of 80 μm, although the larger amount of wear debris from DLC films were generated. Additional wear track observation after the friction tests revealed that the stable tribological properties of textured DLC films were attributed to the promotion of wear debris ejection, which can prevent the plowing inside the apparent area of contact.
Cite this paper
Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.
APA 7
Shimizu, T., Kakegawa, T., & Yang, M. (2014). Micro-texturing of DLC Thin Film Coatings and its Tribological Performance Under Dry Sliding Friction for Microforming Operation. Procedia Engineering, 81, 1884–1889. https://doi.org/10.1016/j.proeng.2014.10.251
MLA 9
Shimizu, Tetsuhide, et al. “Micro-texturing of DLC Thin Film Coatings and its Tribological Performance Under Dry Sliding Friction for Microforming Operation.” Procedia Engineering, vol. 81, 2014, pp. 1884–1889. https://doi.org/10.1016/j.proeng.2014.10.251.
Chicago
Shimizu, Tetsuhide, Tai Kakegawa, and Ming Yang. 2014. “Micro-texturing of DLC Thin Film Coatings and its Tribological Performance Under Dry Sliding Friction for Microforming Operation.” Procedia Engineering 81: 1884–1889. https://doi.org/10.1016/j.proeng.2014.10.251.
Harvard
Shimizu, T., Kakegawa, T. and Yang, M. (2014) ‘Micro-texturing of DLC Thin Film Coatings and its Tribological Performance Under Dry Sliding Friction for Microforming Operation’, Procedia Engineering, 81, pp. 1884–1889. doi:10.1016/j.proeng.2014.10.251.
IEEE
T. Shimizu, T. Kakegawa, and M. Yang, “Micro-texturing of DLC Thin Film Coatings and its Tribological Performance Under Dry Sliding Friction for Microforming Operation,” Procedia Engineering, vol. 81, pp. 1884–1889, 2014, doi: 10.1016/j.proeng.2014.10.251.
BibTeX
@article{shimizu2014micro,
title = {{Micro-texturing of DLC Thin Film Coatings and its Tribological Performance Under Dry Sliding Friction for Microforming Operation}},
author = {Shimizu, Tetsuhide and Kakegawa, Tai and Yang, Ming},
journal = {Procedia Engineering},
year = {2014},
volume = {81},
pages = {1884--1889},
doi = {10.1016/j.proeng.2014.10.251},
url = {https://doi.org/10.1016/j.proeng.2014.10.251}
}
Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)
Citations by year
| Year | Citations | Share of the best year |
|---|---|---|
| 2017 | 3 | |
| 2018 | 6 | |
| 2019 | 6 | |
| 2020 | 7 | |
| 2021 | 1 | |
| 2022 | 4 | |
| 2023 | 1 | |
| 2024 | 2 | |
| 2025 | 1 | |
| 2026 | 1 |
Its field-weighted citation impact is 2.44: it has been cited 2.44 times as often as the average work of the same field, type and year (1.00 is the world average).
Topic and keywords
Physical Sciences › Engineering › Mechanical Engineering › Tribology and Lubrication Engineering
- diamond-like carbon films
- micro-texturing
- dry sliding friction
- microforming
- friction coefficient
- ionized physical vapor deposition
- tribological properties
- ploughing
Work with this paper
Most-cited papers in Engineering
- A Closed‐form Equation for Predicting the Hydraulic Conductivity of Unsaturated SoilsMartinus Th. van Genuchten · Soil Science Society of America Journal · 1980 · 28,197 citations
- An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experimentsW. C. Oliver, George M. Pharr · Journal of materials research/Pratt's guide to venture capital sources · 1992 · 27,379 citations
- Digital communicationsOwen Bishop · Routledge eBooks · 2007 · 24,890 citations
- The empirical mode decomposition and the Hilbert spectrum for nonlinear and non-stationary time series analysisNorden Eh Huang, Zhengwei Shen, Steven R. Long and 6 more · Proceedings of the Royal Society A Mathematical Physical and Engineering Sciences · 1998 · 24,008 citations
- Numerical Heat Transfer and Fluid FlowSuhas V. Patankar · CRC Press eBooks · 2018 · 23,491 citations
Questions about this paper
How do I cite this paper in APA style?
Shimizu, T., Kakegawa, T., & Yang, M. (2014). Micro-texturing of DLC Thin Film Coatings and its Tribological Performance Under Dry Sliding Friction for Microforming Operation. Procedia Engineering, 81, 1884–1889. https://doi.org/10.1016/j.proeng.2014.10.251
How many times has this paper been cited?
33 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.
Is this paper free to read?
Yes. It is open access at Procedia Engineering: sign in and open the PDF from this page.
Who wrote this paper?
Tetsuhide Shimizu, Tai Kakegawa, Ming Yang.
What is the DOI of this paper?
10.1016/j.proeng.2014.10.251, permanently at https://doi.org/10.1016/j.proeng.2014.10.251. Sign in and open it from this page.
Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.