Journal article · 2023 · Open access

Mechanical and Tribological Properties of the CrAl/CrAlN and CrAl/CrAlN-(a-CNx) Multilayers Deposited by HIPIMS

Cecilio Jesús Martínez-González, M. Flores-Jiménez, David Israel Bravo-Bárcenas, O. Jiménez, Martín Flores

Coatings, 13(8), 1344 · Published 31 July 2023 · DOI 10.3390/coatings13081344

Open PDFView at the publisherCite this paper

In brief

“Mechanical and Tribological Properties of the CrAl/CrAlN and CrAl/CrAlN-(a-CNx) Multilayers Deposited by HIPIMS” is a 2023 journal article by Cecilio Jesús Martínez-González and 4 co-authors, published in Coatings. OpenAlex counts 10 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at Coatings.

Citations
10
Most cited in
2025 (5)
Field-weighted impact
1.00
References
60
Authors
5

Abstract

In this study, two CrAl/CrAlN multilayer coatings of 1.5 µm and 1.2 µm thicknesses were deposited from a (50:50) CrAl sectioned target by high-power impulse magnetron sputtering (HIPIMS) onto A11 tool steel to evaluate the effect over mechanical and tribological properties by the addition of an (a-CNx) top layer. XRD analysis showed a CrAlN FCC structure (111) and a Cr phase (110). A glass-like morphology was observed in the CrAl layer and in the (a-CNx) top layer, while the CrAlN layers exhibited a columnar morphology according to the FE-SEM analysis. Raman analysis results confirmed characteristic peaks G and D for the carbon amorphous structure of the (a-CNx) top layer. Nanoindentation results showed comparable hardnesses (23.08 GPa ± 2.8 and 20.58 GPa ± 1.8) in both multilayer coatings. The CrAl/CrAlN multilayer with an (a-CNx) top layer increased the absorption energy capacity and the mechanical potential energy stored. The nano scratch test showed the strongest crack resistance and highest adhesive energy values for the CrAl/CrAlN multilayer. The addition of an (a-CNx) top layer improved the tribological behavior when higher normal loads were applied during the fretting test. Raman analysis showed an increase in the I(D)/I(G) ratio and a formation of a carbon sp2 structure (i.e., graphite-like structure) over the worn surfaces, as well as dissipated energy (J/m) during the fretting test.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Martínez-González, C. J., Flores-Jiménez, M., Bravo-Bárcenas, D. I., Jiménez, O., & Flores, M. (2023). Mechanical and Tribological Properties of the CrAl/CrAlN and CrAl/CrAlN-(a-CNx) Multilayers Deposited by HIPIMS. Coatings, 13(8), 1344. https://doi.org/10.3390/coatings13081344

MLA 9

Martínez-González, Cecilio Jesús, et al. “Mechanical and Tribological Properties of the CrAl/CrAlN and CrAl/CrAlN-(a-CNx) Multilayers Deposited by HIPIMS.” Coatings, vol. 13, no. 8, 2023, p. 1344. https://doi.org/10.3390/coatings13081344.

Chicago

Martínez-González, Cecilio Jesús, M. Flores-Jiménez, David Israel Bravo-Bárcenas, O. Jiménez, and Martín Flores. 2023. “Mechanical and Tribological Properties of the CrAl/CrAlN and CrAl/CrAlN-(a-CNx) Multilayers Deposited by HIPIMS.” Coatings 13 (8): 1344. https://doi.org/10.3390/coatings13081344.

Harvard

Martínez-González, C. J. et al. (2023) ‘Mechanical and Tribological Properties of the CrAl/CrAlN and CrAl/CrAlN-(a-CNx) Multilayers Deposited by HIPIMS’, Coatings, 13(8), p. 1344. doi:10.3390/coatings13081344.

IEEE

C. J. Martínez-González, M. Flores-Jiménez, D. I. Bravo-Bárcenas, O. Jiménez, and M. Flores, “Mechanical and Tribological Properties of the CrAl/CrAlN and CrAl/CrAlN-(a-CNx) Multilayers Deposited by HIPIMS,” Coatings, vol. 13, no. 8, p. 1344, 2023, doi: 10.3390/coatings13081344.

BibTeX

@article{martinezgonzalez2023mechanical,
  title     = {{Mechanical and Tribological Properties of the CrAl/CrAlN and CrAl/CrAlN-(a-CNx) Multilayers Deposited by HIPIMS}},
  author    = {Martínez-González, Cecilio Jesús and Flores-Jiménez, M. and Bravo-Bárcenas, David Israel and Jiménez, O. and Flores, Martín},
  journal   = {Coatings},
  year      = {2023},
  volume    = {13},
  number    = {8},
  pages     = {1344},
  doi       = {10.3390/coatings13081344},
  url       = {https://doi.org/10.3390/coatings13081344}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
202411
202555
202644

Its field-weighted citation impact is 1.00: it has been cited 1.00 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics

  • high power impulse magnetron sputtering
  • tool steel substrates
  • hardness
  • nanoindentation
  • nanoscratch testing
  • fretting wear
  • tribological properties
  • adhesion energy

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Martínez-González, C. J., Flores-Jiménez, M., Bravo-Bárcenas, D. I., Jiménez, O., & Flores, M. (2023). Mechanical and Tribological Properties of the CrAl/CrAlN and CrAl/CrAlN-(a-CNx) Multilayers Deposited by HIPIMS. Coatings, 13(8), 1344. https://doi.org/10.3390/coatings13081344

How many times has this paper been cited?

10 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Coatings: sign in and open the PDF from this page.

Who wrote this paper?

Cecilio Jesús Martínez-González, M. Flores-Jiménez, David Israel Bravo-Bárcenas, O. Jiménez, Martín Flores.

What is the DOI of this paper?

10.3390/coatings13081344, permanently at https://doi.org/10.3390/coatings13081344. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.