Journal article · 2024 · Open access

Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy

Ahsen Ali, Muhammad Umer Younas, Mushtaq Khan, Syed Husain Imran Jaffery, Zarak Khan

International Journal of Precision Engineering and Manufacturing, 26(1), 43–58 · Published 22 October 2024 · DOI 10.1007/s12541-024-01147-9

Open PDFView at the publisherCite this paper

In brief

“Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy” is a 2024 journal article by Ahsen Ali and 4 co-authors, published in International Journal of Precision Engineering and Manufacturing. OpenAlex counts 36 citations as of 17 November 2026, which puts it in the top 1% of works published in 2024 by citations. It is open access under a CC BY licence: the full text is free to read at International Journal of Precision Engineering and Manufacturing.

Citations
36
Most cited in
2026 (24)
Field-weighted impact
4.58
References
58
Authors
5

Abstract

This paper presents the machinability performance of uncoated, single-coated, and multicoated carbide tools during turning of Grade 5 (Ti6Al4V) Titanium alloy, which is challenging to machine due to its distinctive material properties. Coated tools with single-coated Titanium Aluminium Nitride (TiAlN) and multi-coated layer of Titanium Aluminium Nitride with Aluminium Chromium Nitride (TiAlN + AlCrN) coated inserts were utilized to assess surface roughness (Ra), tool wear rate (R), and chip morphologies under various cutting conditions using dry machining. Analysis of the used tools revealed that coated tools exhibited improved tool life and surface quality compared to uncoated tools across all cutting conditions. Multi-coated tools of TiAlN + AlCrN demonstrated a tool life increase of up to 15% compared to uncoated and single-coated tools, with surface roughness improvements ranging from 30 to 45% depending on cutting speed. Chip morphology analysis indicated an increase in the chip reduction coefficient with higher cutting speeds for all tool types. Coated tools exhibited the lowest chip-reduction coefficient due to the presence of TiAlN and AlCrN coatings, which control the tool chip contact length. Conversely, uncoated chip morphology resulted in larger chip thickness values compared to coated tools, particularly at cutting speeds above 100 m/min, attributed to poor heat dissipation and chemical reactions at the tool chip interface. Energy dispersive X-ray scanning electron microscopy (SEM/EDXS) analysis of worn uncoated inserts revealed a higher tendency towards Titanium adhesion compared to coated tools. The proposed multi-layer coatings of (TiAlN + AlCrN) used for dry machining proved highly beneficial for achieving economic machining objectives and may reduce the need for lubrication when processing Ti6Al4V alloys.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Ali, A., Younas, M. U., Khan, M., Jaffery, S. H. I., & Khan, Z. (2024). Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy. International Journal of Precision Engineering and Manufacturing, 26(1), 43–58. https://doi.org/10.1007/s12541-024-01147-9

MLA 9

Ali, Ahsen, et al. “Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy.” International Journal of Precision Engineering and Manufacturing, vol. 26, no. 1, 2024, pp. 43–58. https://doi.org/10.1007/s12541-024-01147-9.

Chicago

Ali, Ahsen, Muhammad Umer Younas, Mushtaq Khan, Syed Husain Imran Jaffery, and Zarak Khan. 2024. “Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy.” International Journal of Precision Engineering and Manufacturing 26 (1): 43–58. https://doi.org/10.1007/s12541-024-01147-9.

Harvard

Ali, A. et al. (2024) ‘Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy’, International Journal of Precision Engineering and Manufacturing, 26(1), pp. 43–58. doi:10.1007/s12541-024-01147-9.

IEEE

A. Ali, M. U. Younas, M. Khan, S. H. I. Jaffery, and Z. Khan, “Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy,” International Journal of Precision Engineering and Manufacturing, vol. 26, no. 1, pp. 43–58, 2024, doi: 10.1007/s12541-024-01147-9.

BibTeX

@article{ali2024machinability,
  title     = {{Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy}},
  author    = {Ali, Ahsen and Younas, Muhammad Umer and Khan, Mushtaq and Jaffery, Syed Husain Imran and Khan, Zarak},
  journal   = {International Journal of Precision Engineering and Manufacturing},
  year      = {2024},
  volume    = {26},
  number    = {1},
  pages     = {43--58},
  doi       = {10.1007/s12541-024-01147-9},
  url       = {https://doi.org/10.1007/s12541-024-01147-9}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization

  • Ti-6Al-4V
  • titanium alloy turning
  • coated carbide tools
  • multilayer coatings
  • TiAlN
  • tool life
  • surface roughness
  • chip morphology

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Ali, A., Younas, M. U., Khan, M., Jaffery, S. H. I., & Khan, Z. (2024). Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy. International Journal of Precision Engineering and Manufacturing, 26(1), 43–58. https://doi.org/10.1007/s12541-024-01147-9

How many times has this paper been cited?

36 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at International Journal of Precision Engineering and Manufacturing: sign in and open the PDF from this page.

Who wrote this paper?

Ahsen Ali, Muhammad Umer Younas, Mushtaq Khan, Syed Husain Imran Jaffery, Zarak Khan.

What is the DOI of this paper?

10.1007/s12541-024-01147-9, permanently at https://doi.org/10.1007/s12541-024-01147-9. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.