Journal article · 2021 · Open access

Investigation of the Wear Behavior of PVD Coated Carbide Tools during Ti6Al4V Machining with Intensive Built Up Edge Formation

Mohammad Shariful Islam Chowdhury, Bipasha Bose, Sushant K. Rawal, German Fox‐Rabinovich, Stephen Clarence Veldhuis

Coatings, 11(3), 266 · Published 25 February 2021 · DOI 10.3390/coatings11030266

Open PDFView at the publisherCite this paper

In brief

“Investigation of the Wear Behavior of PVD Coated Carbide Tools during Ti6Al4V Machining with Intensive Built Up Edge Formation” is a 2021 journal article by Mohammad Shariful Islam Chowdhury and 4 co-authors, published in Coatings. OpenAlex counts 34 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at Coatings.

Citations
34
Most cited in
2026 (10)
Field-weighted impact
1.40
References
42
Authors
5

Abstract

Tool wear phenomena during the machining of titanium alloys are very complex. Severe adhesive interaction at the tool chip interface, especially at low cutting speeds, leads to intensive Built Up Edge (BUE) formation. Additionally, a high cutting temperature causes rapid wear in the carbide inserts due to the low thermal conductivity of titanium alloys. The current research studies the effect of AlTiN and CrN PVD coatings deposited on cutting tools during the rough turning of a Ti6Al4V alloy with severe BUE formation. Tool wear characteristics were evaluated in detail using a Scanning Electron Microscope (SEM) and volumetric wear measurements. Chip morphology analysis was conducted to assess the in situ tribological performance of the coatings. A high temperature–heavy load tribometer that mimics machining conditions was used to analyze the frictional behavior of the coatings. The micromechanical properties of the coatings were also investigated to gain a better understanding of the coating performance. It was demonstrated that the CrN coating possess unique micromechanical properties and tribological adaptive characteristics that minimize BUE formation and significantly improve tool performance during the machining of the Ti6Al4V alloy.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Chowdhury, M. S. I., Bose, B., Rawal, S. K., Fox‐Rabinovich, G., & Veldhuis, S. C. (2021). Investigation of the Wear Behavior of PVD Coated Carbide Tools during Ti6Al4V Machining with Intensive Built Up Edge Formation. Coatings, 11(3), 266. https://doi.org/10.3390/coatings11030266

MLA 9

Chowdhury, Mohammad Shariful Islam, et al. “Investigation of the Wear Behavior of PVD Coated Carbide Tools during Ti6Al4V Machining with Intensive Built Up Edge Formation.” Coatings, vol. 11, no. 3, 2021, p. 266. https://doi.org/10.3390/coatings11030266.

Chicago

Chowdhury, Mohammad Shariful Islam, Bipasha Bose, Sushant K. Rawal, German Fox‐Rabinovich, and Stephen Clarence Veldhuis. 2021. “Investigation of the Wear Behavior of PVD Coated Carbide Tools during Ti6Al4V Machining with Intensive Built Up Edge Formation.” Coatings 11 (3): 266. https://doi.org/10.3390/coatings11030266.

Harvard

Chowdhury, M. S. I. et al. (2021) ‘Investigation of the Wear Behavior of PVD Coated Carbide Tools during Ti6Al4V Machining with Intensive Built Up Edge Formation’, Coatings, 11(3), p. 266. doi:10.3390/coatings11030266.

IEEE

M. S. I. Chowdhury, B. Bose, S. K. Rawal, G. Fox‐Rabinovich, and S. C. Veldhuis, “Investigation of the Wear Behavior of PVD Coated Carbide Tools during Ti6Al4V Machining with Intensive Built Up Edge Formation,” Coatings, vol. 11, no. 3, p. 266, 2021, doi: 10.3390/coatings11030266.

BibTeX

@article{chowdhury2021investigation,
  title     = {{Investigation of the Wear Behavior of PVD Coated Carbide Tools during Ti6Al4V Machining with Intensive Built Up Edge Formation}},
  author    = {Chowdhury, Mohammad Shariful Islam and Bose, Bipasha and Rawal, Sushant K. and Fox‐Rabinovich, German and Veldhuis, Stephen Clarence},
  journal   = {Coatings},
  year      = {2021},
  volume    = {11},
  number    = {3},
  pages     = {266},
  doi       = {10.3390/coatings11030266},
  url       = {https://doi.org/10.3390/coatings11030266}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
202111
202244
202344
202488
202577
20261010

Its field-weighted citation impact is 1.40: it has been cited 1.40 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization

  • tool wear
  • PVD coatings
  • carbide tools
  • Ti-6Al-4V
  • titanium alloy machining
  • built-up edge
  • TiAlN coating
  • CrN coatings

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Chowdhury, M. S. I., Bose, B., Rawal, S. K., Fox‐Rabinovich, G., & Veldhuis, S. C. (2021). Investigation of the Wear Behavior of PVD Coated Carbide Tools during Ti6Al4V Machining with Intensive Built Up Edge Formation. Coatings, 11(3), 266. https://doi.org/10.3390/coatings11030266

How many times has this paper been cited?

34 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Coatings: sign in and open the PDF from this page.

Who wrote this paper?

Mohammad Shariful Islam Chowdhury, Bipasha Bose, Sushant K. Rawal, German Fox‐Rabinovich, Stephen Clarence Veldhuis.

What is the DOI of this paper?

10.3390/coatings11030266, permanently at https://doi.org/10.3390/coatings11030266. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.