Journal article · 2024 · Open access
Investigating the influence of B, C, and N on the tribo-mechanical properties of the chemically complex TiSiBCN thin films using design of experiments
Surface and Coatings Technology, 496, 131643 · Published 10 December 2024 · DOI 10.1016/j.surfcoat.2024.131643
In brief
“Investigating the influence of B, C, and N on the tribo-mechanical properties of the chemically complex TiSiBCN thin films using design of experiments” is a 2024 journal article by Wolfgang Tillmann and 5 co-authors, published in Surface and Coatings Technology. OpenAlex counts 2 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at Surface and Coatings Technology.
- Citations
- 2
- Most cited in
- 2025 (1)
- Field-weighted impact
- 0.26
- References
- 60
- Authors
- 6
Abstract
TiSiBCN thin films show promising properties like high hardness and improved tribological behavior. Adjusting the chemical composition can tailor the properties of these thin films. To investigate this influence, usually one element is varied. However, the interplay and influence of especially the light elements B, C, and N on the tribo-mechanical properties of chemical complex TiSiBCN thin films remain unclear. Therefore, a design of experiment using a central composite design (CCD) was employed to investigate the influences of these light elements on the tribo-mechanical properties of TiSiBCN thin films. TiSiBCN with varying chemical compositions were grown in a magnetron sputtering process by adjusting the cathode power of TiB 2 /TiSi 2 composite targets and the gas flow rates of C 2 H 2 and N 2 . X-ray diffraction (XRD) analysis revealed crystalline phases based on Ti, TiN, TiC, and TiB, with varying degrees of crystallinity dependent on the chemical composition, where the TiSiBCN thin films demonstrate a broad spectrum of mechanical properties, with hardness and elastic modulus ranging from 20.2 to 39.7 GPa and from 222.3 to 405.0 GPa, respectively. Notably, the B content significantly affects the mechanical properties, with the highest hardness and elastic modulus observed at 46.0 at.-% B. In tribometer tests against an Al 2 O 3 ball under dry friction at room temperature, the TiSiBCN thin films also exhibit a broad spectrum of tribological properties, with the coefficients of friction (CoF) between 0.62 and 0.89 and wear rates between 6.4 × 10 −5 and 12.2 × 10 −5 mm 3 /Nm. The lowest CoF of 0.62 with a wear rate of 7.7 × 10 −5 mm 3 /Nm is obtained for TiSiBCN with high amounts of 31.1 at.-% C and 33.5 at.-% N, while high 31.7 at.-% C and low 11.2 at.-% N contents favor the lowest wear rate of 6.4 × 10 −5 mm 3 /Nm with a CoF of 0.74. The tribological results reveal the significant influence of C and N on friction and wear, with TiSiBCN displaying reduced friction and wear tending to have lower hardness. Consequently, TiSiBCN thin films with either high hardness or enhanced friction and wear performance are attainable by adjusting the chemical composition. Depending on the application requirements, the content of the light elements is decisive for the properties of TiSiBCN thin films. The CCD provides insights into the intricate interplay between the chemical composition and tribo-mechanical performance of TiSiBCN. Adjusting the concentrations of B, C, and N within TiSiBCN is crucial for tailoring the tribo-mechanical behavior to…
Cite this paper
Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.
APA 7
Tillmann, W., Urbanczyk, J., Ebady, A. Z., Thewes, A., Bräuer, G., & Dias, N. F. L. (2024). Investigating the influence of B, C, and N on the tribo-mechanical properties of the chemically complex TiSiBCN thin films using design of experiments. Surface and Coatings Technology, 496, 131643. https://doi.org/10.1016/j.surfcoat.2024.131643
MLA 9
Tillmann, Wolfgang, et al. “Investigating the influence of B, C, and N on the tribo-mechanical properties of the chemically complex TiSiBCN thin films using design of experiments.” Surface and Coatings Technology, vol. 496, 2024, p. 131643. https://doi.org/10.1016/j.surfcoat.2024.131643.
Chicago
Tillmann, Wolfgang, Julia Urbanczyk, Ahmad Zahid Ebady, Alexander Thewes, Günter Bräuer, and Nelson Filipe Lopes Dias. 2024. “Investigating the influence of B, C, and N on the tribo-mechanical properties of the chemically complex TiSiBCN thin films using design of experiments.” Surface and Coatings Technology 496: 131643. https://doi.org/10.1016/j.surfcoat.2024.131643.
Harvard
Tillmann, W. et al. (2024) ‘Investigating the influence of B, C, and N on the tribo-mechanical properties of the chemically complex TiSiBCN thin films using design of experiments’, Surface and Coatings Technology, 496, p. 131643. doi:10.1016/j.surfcoat.2024.131643.
IEEE
W. Tillmann, J. Urbanczyk, A. Z. Ebady, A. Thewes, G. Bräuer, and N. F. L. Dias, “Investigating the influence of B, C, and N on the tribo-mechanical properties of the chemically complex TiSiBCN thin films using design of experiments,” Surface and Coatings Technology, vol. 496, p. 131643, 2024, doi: 10.1016/j.surfcoat.2024.131643.
BibTeX
@article{tillmann2024investigating,
title = {{Investigating the influence of B, C, and N on the tribo-mechanical properties of the chemically complex TiSiBCN thin films using design of experiments}},
author = {Tillmann, Wolfgang and Urbanczyk, Julia and Ebady, Ahmad Zahid and Thewes, Alexander and Bräuer, Günter and Dias, Nelson Filipe Lopes},
journal = {Surface and Coatings Technology},
year = {2024},
volume = {496},
pages = {131643},
doi = {10.1016/j.surfcoat.2024.131643},
url = {https://doi.org/10.1016/j.surfcoat.2024.131643}
}
Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)
Topic and keywords
Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics
- boron content
- carbon content
- nitrogen content
- tribomechanical properties
- hardness
- elastic modulus
- friction coefficient
- wear rate
Work with this paper
Most-cited papers in Engineering
- A Closed‐form Equation for Predicting the Hydraulic Conductivity of Unsaturated SoilsMartinus Th. van Genuchten · Soil Science Society of America Journal · 1980 · 28,197 citations
- An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experimentsW. C. Oliver, George M. Pharr · Journal of materials research/Pratt's guide to venture capital sources · 1992 · 27,379 citations
- Digital communicationsOwen Bishop · Routledge eBooks · 2007 · 24,890 citations
- The empirical mode decomposition and the Hilbert spectrum for nonlinear and non-stationary time series analysisNorden Eh Huang, Zhengwei Shen, Steven R. Long and 6 more · Proceedings of the Royal Society A Mathematical Physical and Engineering Sciences · 1998 · 24,008 citations
- Numerical Heat Transfer and Fluid FlowSuhas V. Patankar · CRC Press eBooks · 2018 · 23,491 citations
Questions about this paper
How do I cite this paper in APA style?
Tillmann, W., Urbanczyk, J., Ebady, A. Z., Thewes, A., Bräuer, G., & Dias, N. F. L. (2024). Investigating the influence of B, C, and N on the tribo-mechanical properties of the chemically complex TiSiBCN thin films using design of experiments. Surface and Coatings Technology, 496, 131643. https://doi.org/10.1016/j.surfcoat.2024.131643
How many times has this paper been cited?
2 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.
Is this paper free to read?
Yes. It is open access at Surface and Coatings Technology: sign in and open the full text from this page.
Who wrote this paper?
Wolfgang Tillmann, Julia Urbanczyk, Ahmad Zahid Ebady, Alexander Thewes, Günter Bräuer, Nelson Filipe Lopes Dias.
What is the DOI of this paper?
10.1016/j.surfcoat.2024.131643, permanently at https://doi.org/10.1016/j.surfcoat.2024.131643. Sign in and open it from this page.
Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.