Dissertation · 2005 · Open access

Influência da variação de parâmetros de soldagem sobre a transferência metálica e perfil do cordão no processo MIG/MAG duplo arame

Peter Jan Groetelaars

Universidade Federal de Uberlândia · Published 1 July 2005 · DOI 10.14393/ufu.di.2005.02

Open PDFView at the publisherCite this paper

In brief

“Influência da variação de parâmetros de soldagem sobre a transferência metálica e perfil do cordão no processo MIG/MAG duplo arame” is a 2005 dissertation by Peter Jan Groetelaars, published in Universidade Federal de Uberlândia. OpenAlex counts 9 citations as of 22 November 2026. It is open access: the full text is free to read.

Citations
9
Most cited in
2020 (2)
Authors
1

Abstract

Double Wire MIG/MAG welding process appeared in manufacturing market as an alternative for metals joining, when highest productivity is demanded. However, the most important limitations of this process is the difficulty for parameter settings, as much because of doubled parameters in relation to the normal process as because each wire is dependent of each other. A better knowledge of this technology is fundamental to rule the process and its variables, aiming larger application in industry. With the intent of knowing more about this process, it was proposed this work with two approaches: a) a literature survey on basic operating knowledge and about the influence of the variables on metal transfer and weld bead profile; and b) an experimental evaluation to verify the influence of some variables on metal transfer and weld bead profile. Firstly, a methodology, based on a systematic variation of some parameters without the influence of the others, was proposed and evaluated, with the resulting analyses supported by metal transfer high-speed filming, electrical signal monitoring and weld bead profile measurements. The chosen variables for the experimental work were the arc length, the CO2 content in Ar based shielding gas, the distance between the wires in the torch, the torch attack angle and the ratio between wire feed speeds. The experiments were carried out always with the wire in sequence (leader and trail) and same mean current, total deposition rate and travel speed, so that comparisons could be done. According to the results, there is an ideal arc length, corresponding to the extent in which spray transfer begins. It was observed a strong attraction between drops from each wire ends, regardless the distance between the wires. This attraction turned critical for weldings with high CO2 content in the shielding gas. On the whole, the longer the arc and keeping the torch in a pushing position the wider and larger the beads. The deepest penetration was reached in a condition in which the speed of the wire leader was greater than of the trailing wire. A higher content of CO2 in the shielding gas led to increasing melted area, yet increasing also the arc instability, resulting in high material losses due to spattering.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Groetelaars, P. J. (2005). Influência da variação de parâmetros de soldagem sobre a transferência metálica e perfil do cordão no processo MIG/MAG duplo arame. Universidade Federal de Uberlândia. https://doi.org/10.14393/ufu.di.2005.02

MLA 9

Groetelaars, Peter Jan. “Influência da variação de parâmetros de soldagem sobre a transferência metálica e perfil do cordão no processo MIG/MAG duplo arame.” Universidade Federal de Uberlândia, 2005. https://doi.org/10.14393/ufu.di.2005.02.

Chicago

Groetelaars, Peter Jan. 2005. “Influência da variação de parâmetros de soldagem sobre a transferência metálica e perfil do cordão no processo MIG/MAG duplo arame.” Universidade Federal de Uberlândia. https://doi.org/10.14393/ufu.di.2005.02.

Harvard

Groetelaars, P. J. (2005) ‘Influência da variação de parâmetros de soldagem sobre a transferência metálica e perfil do cordão no processo MIG/MAG duplo arame’, Universidade Federal de Uberlândia. doi:10.14393/ufu.di.2005.02.

IEEE

P. J. Groetelaars, “Influência da variação de parâmetros de soldagem sobre a transferência metálica e perfil do cordão no processo MIG/MAG duplo arame,” Universidade Federal de Uberlândia, 2005, doi: 10.14393/ufu.di.2005.02.

BibTeX

@phdthesis{groetelaars2005influ,
  title     = {{Influência da variação de parâmetros de soldagem sobre a transferência metálica e perfil do cordão no processo MIG/MAG duplo arame}},
  author    = {Groetelaars, Peter Jan},
  year      = {2005},
  doi       = {10.14393/ufu.di.2005.02},
  url       = {https://doi.org/10.14393/ufu.di.2005.02}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
201511
201611
201711
202022
202422
202511

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Welding Techniques and Residual Stresses

  • metal transfer
  • weld bead profile
  • welding parameters
  • arc length
  • wire spacing
  • spray transfer
  • arc instability
  • spatter

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Groetelaars, P. J. (2005). Influência da variação de parâmetros de soldagem sobre a transferência metálica e perfil do cordão no processo MIG/MAG duplo arame. Universidade Federal de Uberlândia. https://doi.org/10.14393/ufu.di.2005.02

How many times has this paper been cited?

9 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access: sign in and open the PDF from this page.

Who wrote this paper?

Peter Jan Groetelaars.

What is the DOI of this paper?

10.14393/ufu.di.2005.02, permanently at https://doi.org/10.14393/ufu.di.2005.02. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.