Journal article · 2025 · Open access

Influence of Deposition Temperature on Microstructure and Properties of Tantalum Oxide Sputtered Coatings

Maria Plamenova Nikolova, Iliyan Tzvetkov

Materials, 18(9), 1895 · Published 22 April 2025 · DOI 10.3390/ma18091895

Open full textCite this paper

In brief

“Influence of Deposition Temperature on Microstructure and Properties of Tantalum Oxide Sputtered Coatings” is a 2025 journal article by Maria Plamenova Nikolova and Iliyan Tzvetkov, published in Materials. OpenAlex counts 12 citations as of 17 November 2026, which puts it in the top 2% of works published in 2025 by citations. It is open access under a CC BY licence: the full text is free to read at Materials.

Citations
12
Most cited in
2026 (12)
Field-weighted impact
2.79
References
70
Authors
2

Abstract

To increase the wear and corrosion resistance of (α + β) titanium-aluminium-vanadium (Ti6Al4V) alloy, ceramic tantalum oxide coatings were deposited by direct current (DC) magnetron sputtering at three different substrate temperatures—400, 450, and 500 °C. The crystallographic structure, surface morphology, chemical compositions, film adhesion, and hardness of the coatings were described using XRD, SEM, EDS, scratch tests, and microhardness measurements. The samples’ ability to withstand corrosion was assessed using electrochemical studies. Results revealed that thin films have an amorphous or crystalline structure dependent on temperature. The film’s thicknesses varied between 560 and 600 nm. With the increase in deposition temperature, the hardness of the film rose. All oxide coatings were tightly adherent to the titanium alloy substrate, and critical force increased from about 8.6 up to 20 N when the temperature rose from 400 to 500 °C. During the polarisation investigations, after 1 h of immersion, a drop in current density (jcorr) verified an improvement in the corrosion resistance of the amorphous and well-crystalline coatings. A two-layer model of the surface film accurately describes the coated systems’ electrochemical behaviour. However, according to the EIS analysis, the well-crystalline film deteriorates greatly, whereas the amorphous film prevents penetration during the 7-day immersion test in SBF. The wettability tests demonstrated the hydrophilic nature of the coatings, and after seven days, the mineralisation of calcium phosphate proves the coatings become bioactive in simulated bodily fluid (SBF). Thus, we produced films of tantalum oxide, which, with the proper deposition parameters, may prove to be appropriate surfaces for titanium-based implant bio-applications.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Nikolova, M. P., & Tzvetkov, I. (2025). Influence of Deposition Temperature on Microstructure and Properties of Tantalum Oxide Sputtered Coatings. Materials, 18(9), 1895. https://doi.org/10.3390/ma18091895

MLA 9

Nikolova, Maria Plamenova, and Iliyan Tzvetkov. “Influence of Deposition Temperature on Microstructure and Properties of Tantalum Oxide Sputtered Coatings.” Materials, vol. 18, no. 9, 2025, p. 1895. https://doi.org/10.3390/ma18091895.

Chicago

Nikolova, Maria Plamenova and Iliyan Tzvetkov. 2025. “Influence of Deposition Temperature on Microstructure and Properties of Tantalum Oxide Sputtered Coatings.” Materials 18 (9): 1895. https://doi.org/10.3390/ma18091895.

Harvard

Nikolova, M. P. and Tzvetkov, I. (2025) ‘Influence of Deposition Temperature on Microstructure and Properties of Tantalum Oxide Sputtered Coatings’, Materials, 18(9), p. 1895. doi:10.3390/ma18091895.

IEEE

M. P. Nikolova and I. Tzvetkov, “Influence of Deposition Temperature on Microstructure and Properties of Tantalum Oxide Sputtered Coatings,” Materials, vol. 18, no. 9, p. 1895, 2025, doi: 10.3390/ma18091895.

BibTeX

@article{nikolova2025influence,
  title     = {{Influence of Deposition Temperature on Microstructure and Properties of Tantalum Oxide Sputtered Coatings}},
  author    = {Nikolova, Maria Plamenova and Tzvetkov, Iliyan},
  journal   = {Materials},
  year      = {2025},
  volume    = {18},
  number    = {9},
  pages     = {1895},
  doi       = {10.3390/ma18091895},
  url       = {https://doi.org/10.3390/ma18091895}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Surface Treatment and Coatings

  • tantalum oxide coatings
  • deposition temperature
  • Ti-6Al-4V
  • titanium alloys
  • corrosion resistance
  • wear resistance
  • amorphous coatings
  • crystalline coatings

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Nikolova, M. P., & Tzvetkov, I. (2025). Influence of Deposition Temperature on Microstructure and Properties of Tantalum Oxide Sputtered Coatings. Materials, 18(9), 1895. https://doi.org/10.3390/ma18091895

How many times has this paper been cited?

12 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Materials: sign in and open the full text from this page.

Who wrote this paper?

Maria Plamenova Nikolova, Iliyan Tzvetkov.

What is the DOI of this paper?

10.3390/ma18091895, permanently at https://doi.org/10.3390/ma18091895. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.