Journal article · 2021 · Open access

Impact of Ar Flow Rates on Micro-Structural Properties of WS2 Thin Film by RF Magnetron Sputtering

Md. Akhtaruzzaman, Md. Shahiduzzaman, Nowshad Amin, Ghulam Muhammad, Mohammad Aminul Islam, Md Khan Sobayel Bin Rafiq, Kamaruzzaman Sopian

Nanomaterials, 11(7), 1635 · Published 22 June 2021 · DOI 10.3390/nano11071635

Open PDFView at the publisherCite this paper

In brief

“Impact of Ar Flow Rates on Micro-Structural Properties of WS2 Thin Film by RF Magnetron Sputtering” is a 2021 journal article by Md. Akhtaruzzaman and 6 co-authors, published in Nanomaterials. OpenAlex counts 34 citations as of 20 November 2026. It is open access under a CC BY licence: the full text is free to read at Nanomaterials.

Citations
34
Most cited in
2025 (10)
Field-weighted impact
1.10
References
62
Authors
7

Abstract

Tungsten disulfide (WS2) thin films were deposited on soda-lime glass (SLG) substrates using radio frequency (RF) magnetron sputtering at different Ar flow rates (3 to 7 sccm). The effect of Ar flow rates on the structural, morphology, and electrical properties of the WS2 thin films was investigated thoroughly. Structural analysis exhibited that all the as-grown films showed the highest peak at (101) plane corresponds to rhombohedral phase. The crystalline size of the film ranged from 11.2 to 35.6 nm, while dislocation density ranged from 7.8 × 1014 to 26.29 × 1015 lines/m2. All these findings indicate that as-grown WS2 films are induced with various degrees of defects, which were visible in the FESEM images. FESEM images also identified the distorted crystallographic structure for all the films except the film deposited at 5 sccm of Ar gas flow rate. EDX analysis found that all the films were having a sulfur deficit and suggested that WS2 thin film bears edge defects in its structure. Further, electrical analysis confirms that tailoring of structural defects in WS2 thin film can be possible by the varying Ar gas flow rates. All these findings articulate that Ar gas flow rate is one of the important process parameters in RF magnetron sputtering that could affect the morphology, electrical properties, and structural properties of WS2 thin film. Finally, the simulation study validates the experimental results and encourages the use of WS2 as a buffer layer of CdTe-based solar cells.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Akhtaruzzaman, M., Shahiduzzaman, M., Amin, N., Muhammad, G., Islam, M. A., Bin Rafiq, M. K. S., & Sopian, K. (2021). Impact of Ar Flow Rates on Micro-Structural Properties of WS2 Thin Film by RF Magnetron Sputtering. Nanomaterials, 11(7), 1635. https://doi.org/10.3390/nano11071635

MLA 9

Akhtaruzzaman, Md., et al. “Impact of Ar Flow Rates on Micro-Structural Properties of WS2 Thin Film by RF Magnetron Sputtering.” Nanomaterials, vol. 11, no. 7, 2021, p. 1635. https://doi.org/10.3390/nano11071635.

Chicago

Akhtaruzzaman, Md., Md. Shahiduzzaman, Nowshad Amin, Ghulam Muhammad, Mohammad Aminul Islam, Md Khan Sobayel Bin Rafiq, and Kamaruzzaman Sopian. 2021. “Impact of Ar Flow Rates on Micro-Structural Properties of WS2 Thin Film by RF Magnetron Sputtering.” Nanomaterials 11 (7): 1635. https://doi.org/10.3390/nano11071635.

Harvard

Akhtaruzzaman, M. et al. (2021) ‘Impact of Ar Flow Rates on Micro-Structural Properties of WS2 Thin Film by RF Magnetron Sputtering’, Nanomaterials, 11(7), p. 1635. doi:10.3390/nano11071635.

IEEE

M. Akhtaruzzaman et al., “Impact of Ar Flow Rates on Micro-Structural Properties of WS2 Thin Film by RF Magnetron Sputtering,” Nanomaterials, vol. 11, no. 7, p. 1635, 2021, doi: 10.3390/nano11071635.

BibTeX

@article{akhtaruzzaman2021impact,
  title     = {{Impact of Ar Flow Rates on Micro-Structural Properties of WS2 Thin Film by RF Magnetron Sputtering}},
  author    = {Akhtaruzzaman, Md. and Shahiduzzaman, Md. and Amin, Nowshad and Muhammad, Ghulam and Islam, Mohammad Aminul and Bin Rafiq, Md Khan Sobayel and Sopian, Kamaruzzaman},
  journal   = {Nanomaterials},
  year      = {2021},
  volume    = {11},
  number    = {7},
  pages     = {1635},
  doi       = {10.3390/nano11071635},
  url       = {https://doi.org/10.3390/nano11071635}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
202111
202244
202344
202477
20251010
202688

Its field-weighted citation impact is 1.10: it has been cited 1.10 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Electrical and Electronic Engineering › Chalcogenide Semiconductor Thin Films

  • tungsten disulfide
  • WS2 thin films
  • argon flow rate
  • RF magnetron sputtering
  • microstructure
  • crystallite size
  • dislocation density
  • sulfur deficiency

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Akhtaruzzaman, M., Shahiduzzaman, M., Amin, N., Muhammad, G., Islam, M. A., Bin Rafiq, M. K. S., & Sopian, K. (2021). Impact of Ar Flow Rates on Micro-Structural Properties of WS2 Thin Film by RF Magnetron Sputtering. Nanomaterials, 11(7), 1635. https://doi.org/10.3390/nano11071635

How many times has this paper been cited?

34 times, according to OpenAlex on 20 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Nanomaterials: sign in and open the PDF from this page.

Who wrote this paper?

Md. Akhtaruzzaman, Md. Shahiduzzaman, Nowshad Amin, Ghulam Muhammad, Mohammad Aminul Islam, Md Khan Sobayel Bin Rafiq, Kamaruzzaman Sopian.

What is the DOI of this paper?

10.3390/nano11071635, permanently at https://doi.org/10.3390/nano11071635. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 20 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.