Journal article · 2021 · Open access
Fabrication and Mechanical Properties of Cr2AlC MAX Phase Coatings on TiBw/Ti6Al4V Composite Prepared by HiPIMS
Materials, 14(4), 826 · Published 9 February 2021 · DOI 10.3390/ma14040826
In brief
“Fabrication and Mechanical Properties of Cr2AlC MAX Phase Coatings on TiBw/Ti6Al4V Composite Prepared by HiPIMS” is a 2021 journal article by Muhammad Waqas Qureshi and 4 co-authors, published in Materials. OpenAlex counts 27 citations as of 16 November 2026. It is open access under a CC BY licence: the full text is free to read at Materials.
- Citations
- 27
- Most cited in
- 2024 (8)
- Field-weighted impact
- 1.35
- References
- 82
- Authors
- 5
Abstract
The high-power impulse magnetron sputtering (HiPIMS) technique is widely used owing to the high degree of ionization and the ability to synthesize high-quality coatings with a dense structure and smooth morphology. However, limited efforts have been made in the deposition of MAX phase coatings through HiPIMS compared with direct current magnetron sputtering (DCMS), and tailoring of the coatings’ properties by process parameters such as pulse width and frequency is lacking. In this study, the Cr2AlC MAX phase coatings are deposited through HiPIMS on network structured TiBw/Ti6Al4V composite. A comparative study was made to investigate the effect of average power by varying frequency (1.2–1.6 kHz) and pulse width (20–60 μs) on the deposition rate, microstructure, crystal orientation, and current waveforms of Cr2AlC MAX phase coatings. X-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM) were used to characterize the deposited coatings. The influence of pulse width was more profound than the frequency in increasing the average power of HiPIMS. The XRD results showed that ex situ annealing converted amorphous Cr-Al-C coatings into polycrystalline Cr2AlC MAX phase. It was noticed that the deposition rate, gas temperature, and roughness of Cr2AlC coatings depend on the average power, and the deposition rate increased from 16.5 to 56.3 nm/min. Moreover, the Cr2AlC MAX phase coatings produced by HiPIMS exhibits the improved hardness and modulus of 19.7 GPa and 286 GPa, with excellent fracture toughness and wear resistance because of dense and column-free morphology as the main characteristic.
Cite this paper
Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.
APA 7
Qureshi, M. W., Ma, X., Tang, G., Miao, B., & Niu, J. (2021). Fabrication and Mechanical Properties of Cr2AlC MAX Phase Coatings on TiBw/Ti6Al4V Composite Prepared by HiPIMS. Materials, 14(4), 826. https://doi.org/10.3390/ma14040826
MLA 9
Qureshi, Muhammad Waqas, et al. “Fabrication and Mechanical Properties of Cr2AlC MAX Phase Coatings on TiBw/Ti6Al4V Composite Prepared by HiPIMS.” Materials, vol. 14, no. 4, 2021, p. 826. https://doi.org/10.3390/ma14040826.
Chicago
Qureshi, Muhammad Waqas, Xinxin Ma, Guangze Tang, Bin Miao, and Junbo Niu. 2021. “Fabrication and Mechanical Properties of Cr2AlC MAX Phase Coatings on TiBw/Ti6Al4V Composite Prepared by HiPIMS.” Materials 14 (4): 826. https://doi.org/10.3390/ma14040826.
Harvard
Qureshi, M. W. et al. (2021) ‘Fabrication and Mechanical Properties of Cr2AlC MAX Phase Coatings on TiBw/Ti6Al4V Composite Prepared by HiPIMS’, Materials, 14(4), p. 826. doi:10.3390/ma14040826.
IEEE
M. W. Qureshi, X. Ma, G. Tang, B. Miao, and J. Niu, “Fabrication and Mechanical Properties of Cr2AlC MAX Phase Coatings on TiBw/Ti6Al4V Composite Prepared by HiPIMS,” Materials, vol. 14, no. 4, p. 826, 2021, doi: 10.3390/ma14040826.
BibTeX
@article{qureshi2021fabrication,
title = {{Fabrication and Mechanical Properties of Cr2AlC MAX Phase Coatings on TiBw/Ti6Al4V Composite Prepared by HiPIMS}},
author = {Qureshi, Muhammad Waqas and Ma, Xinxin and Tang, Guangze and Miao, Bin and Niu, Junbo},
journal = {Materials},
year = {2021},
volume = {14},
number = {4},
pages = {826},
doi = {10.3390/ma14040826},
url = {https://doi.org/10.3390/ma14040826}
}
Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)
Citations by year
| Year | Citations | Share of the best year |
|---|---|---|
| 2021 | 5 | |
| 2022 | 1 | |
| 2023 | 5 | |
| 2024 | 8 | |
| 2025 | 5 | |
| 2026 | 3 |
Its field-weighted citation impact is 1.35: it has been cited 1.35 times as often as the average work of the same field, type and year (1.00 is the world average).
Topic and keywords
Physical Sciences › Materials Science › Materials Chemistry › MXene and MAX Phase Materials
- high power impulse magnetron sputtering
- pulse duration
- deposition rate
- ex-situ annealing
- coating microstructure
- crystal orientation
- current waveform
- hardness
Work with this paper
Most-cited papers in Materials Science
- Electric Field Effect in Atomically Thin Carbon FilmsKostya S. Novoselov, Andre K. Geim, Sergey V. Morozov and 5 more · Science · 2004 · 67,474 citations
- Revised effective ionic radii and systematic studies of interatomic distances in halides and chalcogenidesROBERT D. SHANNON · Acta Crystallographica Section A · 1976 · 66,944 citations
- Ab initio molecular dynamics for liquid metalsGeorg Kresse, J. Häfner · Physical review. B, Condensed matter · 1993 · 46,320 citations
- Helical microtubules of graphitic carbonSumio Iijima · Nature · 1991 · 43,639 citations
- The rise of grapheneAndre K. Geim, Kostya S. Novoselov · Nature Materials · 2007 · 40,328 citations
Questions about this paper
How do I cite this paper in APA style?
Qureshi, M. W., Ma, X., Tang, G., Miao, B., & Niu, J. (2021). Fabrication and Mechanical Properties of Cr2AlC MAX Phase Coatings on TiBw/Ti6Al4V Composite Prepared by HiPIMS. Materials, 14(4), 826. https://doi.org/10.3390/ma14040826
How many times has this paper been cited?
27 times, according to OpenAlex on 16 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.
Is this paper free to read?
Yes. It is open access: read the free full text at Materials.
Who wrote this paper?
Muhammad Waqas Qureshi, Xinxin Ma, Guangze Tang, Bin Miao, Junbo Niu.
What is the DOI of this paper?
10.3390/ma14040826. The permanent link is https://doi.org/10.3390/ma14040826.
Bibliographic data from OpenAlex (CC0), last checked 16 November 2026. ResearchGuru does not host this paper; the links go to the publisher or the repository that does.