Paper · 2013 · Open access
Experimental Evaluation of Innovative Tools for Ti-6Al-4V Turning
Key engineering materials, 554-557, 1941–1952 · Published 13 June 2013 · DOI 10.4028/www.scientific.net/kem.554-557.1941
In brief
“Experimental Evaluation of Innovative Tools for Ti-6Al-4V Turning” is a 2013 paper by Matteo Strano and 3 co-authors, published in Key engineering materials. OpenAlex counts 3 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at Key engineering materials.
- Citations
- 3
- Most cited in
- 2015 (1)
- Field-weighted impact
- 0.47
- References
- 25
- Authors
- 4
Abstract
Titanium alloys, mainly because of their poor thermal conductivity, need to be cut at relatively low cutting speeds, with obvious negative consequences on the profitability of machining. An important amount of research activities has been done in order to increase productivity in titanium machining operations: high performance coatings and innovative technologies to improve inserts resistance to wear represent promising solutions. In this work, the cutting performance in Ti6Al4V rough turning of an innovative TiAlN coating obtained by Physical Vapor Deposition (PVD) magnetron sputtering and the effects of a Deep Cryogenic Treatment (DCT) have been experimentally investigated and a statistical analysis of the results has been performed. Typical commercially available inserts (TiAlN-AlCrO coated) have been used as a benchmark. Preliminary hardness and thermal conductivity measurements tests have been performed on the three types of tool to determine the differences caused by the different coatings and thermal treatment. The experiments have been conducted using a full factorial design in order to statistically evaluate, using ANOVA, the significance of the input factors on the process most interesting outputs. tool life and other variables of interest with different process parameters. The considered input factors are type of insert, cutting speed and feed rate. The analysed responses are average flank wear, surface roughness, cutting forces, coefficient of friction and chip morphology. The results show that even if friction coefficients are lower for standard tools, innovative inserts exhibit a higher resistance to wear. Taylor’s law parameters of PVD coated tools, with and without DCT have been determined, clearly showing that cryogenically treated tools present higher resistance at higher cutting speeds, mainly due to their superior hardness. In conclusion, it appears that relevant improvements of productivity or profitability of titanium turning can be obtained if an advanced PVD coating, deposited by magnetron sputtering is used on tungsten carbide inserts and if deep cryogenic of the inserts is performed afterwards.
Cite this paper
Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.
APA 7
Strano, M., Albertelli, P., Chiappini, E., & Tirelli, S. (2013). Experimental Evaluation of Innovative Tools for Ti-6Al-4V Turning. Key engineering materials, 554-557, 1941–1952. https://doi.org/10.4028/www.scientific.net/kem.554-557.1941
MLA 9
Strano, Matteo, et al. “Experimental Evaluation of Innovative Tools for Ti-6Al-4V Turning.” Key engineering materials, vol. 554-557, 2013, pp. 1941–1952. https://doi.org/10.4028/www.scientific.net/kem.554-557.1941.
Chicago
Strano, Matteo, Paolo Albertelli, Elio Chiappini, and Stefano Tirelli. 2013. “Experimental Evaluation of Innovative Tools for Ti-6Al-4V Turning.” Key engineering materials 554-557: 1941–1952. https://doi.org/10.4028/www.scientific.net/kem.554-557.1941.
Harvard
Strano, M. et al. (2013) ‘Experimental Evaluation of Innovative Tools for Ti-6Al-4V Turning’, Key engineering materials, 554-557, pp. 1941–1952. doi:10.4028/www.scientific.net/kem.554-557.1941.
IEEE
M. Strano, P. Albertelli, E. Chiappini, and S. Tirelli, “Experimental Evaluation of Innovative Tools for Ti-6Al-4V Turning,” Key engineering materials, vol. 554-557, pp. 1941–1952, 2013, doi: 10.4028/www.scientific.net/kem.554-557.1941.
BibTeX
@article{strano2013experimental,
title = {{Experimental Evaluation of Innovative Tools for Ti-6Al-4V Turning}},
author = {Strano, Matteo and Albertelli, Paolo and Chiappini, Elio and Tirelli, Stefano},
journal = {Key engineering materials},
year = {2013},
volume = {554-557},
pages = {1941--1952},
doi = {10.4028/www.scientific.net/kem.554-557.1941},
url = {https://doi.org/10.4028/www.scientific.net/kem.554-557.1941}
}
Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)
Citations by year
| Year | Citations | Share of the best year |
|---|---|---|
| 2015 | 1 | |
| 2019 | 1 | |
| 2026 | 1 |
Its field-weighted citation impact is 0.47: it has been cited 0.47 times as often as the average work of the same field, type and year (1.00 is the world average).
Topic and keywords
Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- Ti-6Al-4V
- TiAlN coating
- deep cryogenic treatment
- tungsten carbide inserts
- tool wear resistance
- flank wear
- surface roughness
- cutting force
Work with this paper
Most-cited papers in Engineering
- A Closed‐form Equation for Predicting the Hydraulic Conductivity of Unsaturated SoilsMartinus Th. van Genuchten · Soil Science Society of America Journal · 1980 · 28,197 citations
- An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experimentsW. C. Oliver, George M. Pharr · Journal of materials research/Pratt's guide to venture capital sources · 1992 · 27,379 citations
- Digital communicationsOwen Bishop · Routledge eBooks · 2007 · 24,890 citations
- The empirical mode decomposition and the Hilbert spectrum for nonlinear and non-stationary time series analysisNorden Eh Huang, Zhengwei Shen, Steven R. Long and 6 more · Proceedings of the Royal Society A Mathematical Physical and Engineering Sciences · 1998 · 24,008 citations
- Numerical Heat Transfer and Fluid FlowSuhas V. Patankar · CRC Press eBooks · 2018 · 23,491 citations
Questions about this paper
How do I cite this paper in APA style?
Strano, M., Albertelli, P., Chiappini, E., & Tirelli, S. (2013). Experimental Evaluation of Innovative Tools for Ti-6Al-4V Turning. Key engineering materials, 554-557, 1941–1952. https://doi.org/10.4028/www.scientific.net/kem.554-557.1941
How many times has this paper been cited?
3 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.
Is this paper free to read?
Yes. It is open access at Key engineering materials: sign in and open the full text from this page.
Who wrote this paper?
Matteo Strano, Paolo Albertelli, Elio Chiappini, Stefano Tirelli.
What is the DOI of this paper?
10.4028/www.scientific.net/kem.554-557.1941, permanently at https://doi.org/10.4028/www.scientific.net/kem.554-557.1941. Sign in and open it from this page.
Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.