Journal article · 2023 · Open access
Evaluation of tribological interactions and machinability of Ti6Al4V alloy during finish turning under different cooling conditions
Tribology International, 189, 109002 · Published 1 October 2023 · DOI 10.1016/j.triboint.2023.109002
In brief
“Evaluation of tribological interactions and machinability of Ti6Al4V alloy during finish turning under different cooling conditions” is a 2023 journal article by Kamil Leksycki and 6 co-authors, published in Tribology International. OpenAlex counts 55 citations as of 17 November 2026, which puts it in the top 1% of works published in 2023 by citations. It is open access under a CC BY-NC-ND licence: the full text is free to read at Tribology International.
- Citations
- 55
- Most cited in
- 2024 (29)
- Field-weighted impact
- 5.25
- References
- 55
- Authors
- 7
Abstract
The titanium alloy Ti6Al4V has several applications and is considered a difficult-to-machine material. This study evaluates some tribological interactions in finish turning of Ti6Al4V titanium alloy, including the tool wear, and coefficient of friction in tool-chip interface. Subsequently, the machinability of Ti6Al4V titanium alloy has been investigated, considering the chip geometry, chip thickness ratio, as well as changes in the total cutting force components. The turning process was carried out over a wide range of the feed rate (f) and depths of cut (ap) using hard carbide, GC1115 grade, inserts with double-layer PVD coating. The finish turning tests were conducted under the dry, flood, and MQL (minimum quantity lubrication) cutting conditions. It was found that favorable chip shapes (arc loose) were obtained in the range ap = 0.9–1.2 mm and f = 0.25–0.4 mm/rev. Increasing the f clearly affects the formation of a serrated chip. In addition, the intensity of tool wear, as well as the variations of cutting forces and chip thickness ratios were strongly affected by the applied cooling/lubricating condition. Compared to wet conditions, the Kh values decrease by ~22% with dry machining and by ~12% with MQL. Compared to wet conditions, for dry machining the cutting forces decrease to 70% and with MQL to 8%. The cumulative wear rate under dry machining increases by 18% compared to wet conditions, and with MQL reduces by 19%.
Cite this paper
Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.
APA 7
Leksycki, K., Maruda, R. W., Feldshtein, E. E., Wojciechowski, S., Habrat, W. F., Gupta, M. K., & Królczyk, G. (2023). Evaluation of tribological interactions and machinability of Ti6Al4V alloy during finish turning under different cooling conditions. Tribology International, 189, 109002. https://doi.org/10.1016/j.triboint.2023.109002
MLA 9
Leksycki, Kamil, et al. “Evaluation of tribological interactions and machinability of Ti6Al4V alloy during finish turning under different cooling conditions.” Tribology International, vol. 189, 2023, p. 109002. https://doi.org/10.1016/j.triboint.2023.109002.
Chicago
Leksycki, Kamil, Radosław W. Maruda, Eugene E. Feldshtein, Szymon Wojciechowski, Witold F. Habrat, Munish Kumar Gupta, and Grzegorz Królczyk. 2023. “Evaluation of tribological interactions and machinability of Ti6Al4V alloy during finish turning under different cooling conditions.” Tribology International 189: 109002. https://doi.org/10.1016/j.triboint.2023.109002.
Harvard
Leksycki, K. et al. (2023) ‘Evaluation of tribological interactions and machinability of Ti6Al4V alloy during finish turning under different cooling conditions’, Tribology International, 189, p. 109002. doi:10.1016/j.triboint.2023.109002.
IEEE
K. Leksycki et al., “Evaluation of tribological interactions and machinability of Ti6Al4V alloy during finish turning under different cooling conditions,” Tribology International, vol. 189, p. 109002, 2023, doi: 10.1016/j.triboint.2023.109002.
BibTeX
@article{leksycki2023evaluation,
title = {{Evaluation of tribological interactions and machinability of Ti6Al4V alloy during finish turning under different cooling conditions}},
author = {Leksycki, Kamil and Maruda, Radosław W. and Feldshtein, Eugene E. and Wojciechowski, Szymon and Habrat, Witold F. and Gupta, Munish Kumar and Królczyk, Grzegorz},
journal = {Tribology International},
year = {2023},
volume = {189},
pages = {109002},
doi = {10.1016/j.triboint.2023.109002},
url = {https://doi.org/10.1016/j.triboint.2023.109002}
}
Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)
Citations by year
| Year | Citations | Share of the best year |
|---|---|---|
| 2024 | 29 | |
| 2025 | 15 | |
| 2026 | 11 |
Its field-weighted citation impact is 5.25: it has been cited 5.25 times as often as the average work of the same field, type and year (1.00 is the world average).
Topic and keywords
Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- Ti-6Al-4V
- titanium alloys
- finish turning
- machinability
- tool wear
- friction coefficient
- tool-chip interface
- chip geometry
Work with this paper
Most-cited papers in Engineering
- A Closed‐form Equation for Predicting the Hydraulic Conductivity of Unsaturated SoilsMartinus Th. van Genuchten · Soil Science Society of America Journal · 1980 · 28,197 citations
- An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experimentsW. C. Oliver, George M. Pharr · Journal of materials research/Pratt's guide to venture capital sources · 1992 · 27,379 citations
- Digital communicationsOwen Bishop · Routledge eBooks · 2007 · 24,890 citations
- The empirical mode decomposition and the Hilbert spectrum for nonlinear and non-stationary time series analysisNorden Eh Huang, Zhengwei Shen, Steven R. Long and 6 more · Proceedings of the Royal Society A Mathematical Physical and Engineering Sciences · 1998 · 24,008 citations
- Numerical Heat Transfer and Fluid FlowSuhas V. Patankar · CRC Press eBooks · 2018 · 23,491 citations
Questions about this paper
How do I cite this paper in APA style?
Leksycki, K., Maruda, R. W., Feldshtein, E. E., Wojciechowski, S., Habrat, W. F., Gupta, M. K., & Królczyk, G. (2023). Evaluation of tribological interactions and machinability of Ti6Al4V alloy during finish turning under different cooling conditions. Tribology International, 189, 109002. https://doi.org/10.1016/j.triboint.2023.109002
How many times has this paper been cited?
55 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.
Is this paper free to read?
Yes. It is open access at Tribology International: sign in and open the full text from this page.
Who wrote this paper?
Kamil Leksycki, Radosław W. Maruda, Eugene E. Feldshtein, Szymon Wojciechowski, Witold F. Habrat, Munish Kumar Gupta, Grzegorz Królczyk.
What is the DOI of this paper?
10.1016/j.triboint.2023.109002, permanently at https://doi.org/10.1016/j.triboint.2023.109002. Sign in and open it from this page.
Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.