Paper · 2015 · Open access

Effects of Tungsten Addition on Mechanical and Tribological Properties of Carbon Nitride Prepared by DC Magnetron Sputtering

Yean Liang Su, Yue-Feng Lin, Shun Hui Yao, Chia‐Jui Hsu

Key engineering materials, 642, 24–29 · Published 15 April 2015 · DOI 10.4028/www.scientific.net/kem.642.24

Open full textCite this paper

In brief

“Effects of Tungsten Addition on Mechanical and Tribological Properties of Carbon Nitride Prepared by DC Magnetron Sputtering” is a 2015 paper by Yean Liang Su and 3 co-authors, published in Key engineering materials. OpenAlex counts 2 citations as of 17 November 2026, which puts it in the top 7% of works published in 2015 by citations. It is open access under a CC BY licence: the full text is free to read at Key engineering materials.

Citations
2
Most cited in
2017 (2)
Field-weighted impact
0.49
References
19
Authors
4

Abstract

Carbon nitride coatings doped with tungsten were deposited on high speed steel disks by unbalanced DC magnetron sputtering using nitrogen-argon mixture gas. The coatings were deposited on three different types of interlayer (Ti, Ti/TiN and Ti/TiC), and the tungsten target current was varied from 0 to 0.9 A. Surface morphology of the coatings were measured by roughness testing and scanning electron microscopy (SEM). In addition, the chemical composition and depth profile were analyzed by X-ray Diffraction (XRD) analysis, Raman spectroscopy, and glow discharge spectroscopy (GDS). Finally, the hardness (H) and elasticity (E) were measured by nanoindentation and a Rockwell indentation test, while the tribological properties were tested using a pin-on-disk tribometer. After all, the coatings were measured by cutting testing of tuning inserts and micro-drillers. It is found that all of the coatings are amorphous and have a thickness of approximately 1.5 μm. Moreover, the nitrogen content is around 30 at%, while the tungsten content varies in the range of 0-9 at%. In addition, the hardness values are in the range of 15-20 GPa and the elasticity varies from 236 to 274 GPa. A good correlation is observed between the wear resistance and the indentation adhesion level. Furthermore, it is found that the hardness is not significantly correlated to the tungsten content and the coatings deposited on the Ti/TiC interlayer have greater adhesion. Finally, the coatings generally have a very low coefficient of friction (0.01-0.3) and a wear coefficient as low as 10-6 mm3/Nm, and the CN/TiC coating reduced 41% and 43% of flank wear in the cutting testing of turning inserts and micro-drillers respectively.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Su, Y. L., Lin, Y.-F., Yao, S. H., & Hsu, C. (2015). Effects of Tungsten Addition on Mechanical and Tribological Properties of Carbon Nitride Prepared by DC Magnetron Sputtering. Key engineering materials, 642, 24–29. https://doi.org/10.4028/www.scientific.net/kem.642.24

MLA 9

Su, Yean Liang, et al. “Effects of Tungsten Addition on Mechanical and Tribological Properties of Carbon Nitride Prepared by DC Magnetron Sputtering.” Key engineering materials, vol. 642, 2015, pp. 24–29. https://doi.org/10.4028/www.scientific.net/kem.642.24.

Chicago

Su, Yean Liang, Yue-Feng Lin, Shun Hui Yao, and Chia‐Jui Hsu. 2015. “Effects of Tungsten Addition on Mechanical and Tribological Properties of Carbon Nitride Prepared by DC Magnetron Sputtering.” Key engineering materials 642: 24–29. https://doi.org/10.4028/www.scientific.net/kem.642.24.

Harvard

Su, Y. L. et al. (2015) ‘Effects of Tungsten Addition on Mechanical and Tribological Properties of Carbon Nitride Prepared by DC Magnetron Sputtering’, Key engineering materials, 642, pp. 24–29. doi:10.4028/www.scientific.net/kem.642.24.

IEEE

Y. L. Su, Y.-F. Lin, S. H. Yao, and C. Hsu, “Effects of Tungsten Addition on Mechanical and Tribological Properties of Carbon Nitride Prepared by DC Magnetron Sputtering,” Key engineering materials, vol. 642, pp. 24–29, 2015, doi: 10.4028/www.scientific.net/kem.642.24.

BibTeX

@article{su2015effects,
  title     = {{Effects of Tungsten Addition on Mechanical and Tribological Properties of Carbon Nitride Prepared by DC Magnetron Sputtering}},
  author    = {Su, Yean Liang and Lin, Yue-Feng and Yao, Shun Hui and Hsu, Chia‐Jui},
  journal   = {Key engineering materials},
  year      = {2015},
  volume    = {642},
  pages     = {24--29},
  doi       = {10.4028/www.scientific.net/kem.642.24},
  url       = {https://doi.org/10.4028/www.scientific.net/kem.642.24}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics

  • DC magnetron sputtering
  • high-speed steel substrates
  • interlayer coating
  • coating hardness
  • elastic modulus
  • tribological properties
  • wear resistance
  • coating adhesion

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Su, Y. L., Lin, Y.-F., Yao, S. H., & Hsu, C. (2015). Effects of Tungsten Addition on Mechanical and Tribological Properties of Carbon Nitride Prepared by DC Magnetron Sputtering. Key engineering materials, 642, 24–29. https://doi.org/10.4028/www.scientific.net/kem.642.24

How many times has this paper been cited?

2 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Key engineering materials: sign in and open the full text from this page.

Who wrote this paper?

Yean Liang Su, Yue-Feng Lin, Shun Hui Yao, Chia‐Jui Hsu.

What is the DOI of this paper?

10.4028/www.scientific.net/kem.642.24, permanently at https://doi.org/10.4028/www.scientific.net/kem.642.24. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.