Journal article · 2003 · Open access

Effect of Silicon Content on Tempered Hardness, High Temperature Strength and Toughness of Hot Working Tool Steels

Masahide Umino, Tomoaki Sera, Kunio KONDO, Yasutaka Okada, Harushige Tubakino

鐵と鋼 : 日本鐡鋼協會々誌, 89(6), 673–679 · Published 1 January 2003 · DOI 10.2355/tetsutohagane1955.89.6_673

Open PDFView at the publisherCite this paper

In brief

“Effect of Silicon Content on Tempered Hardness, High Temperature Strength and Toughness of Hot Working Tool Steels” is a 2003 journal article by Masahide Umino and 4 co-authors, published in 鐵と鋼 : 日本鐡鋼協會々誌. OpenAlex counts 14 citations as of 22 November 2026. It is open access: the full text is free to read at 鐵と鋼 : 日本鐡鋼協會々誌.

Citations
14
Most cited in
2023 (3)
References
13
Authors
5

Abstract

In order to prevent heat cracks of tool steels in hot working, steels of high toughness and superior high-temperature strength has been developed. Typical hot-working tool steels, such as JIS SKD6, 61 and 62, contain about 1 mass% silicon. In this study, the influence of the silicon content was investigated on the 4 mass%Cr-MMo-V-Ni tool steel in the following points;1) secondary hardening after tempering2) high-temperature strength and room-temperature toughness with various cooling rates during quenchingThe secondary hardening peak of the tool steel decreases with the decrease in its silicon content, due to the cementite precipitation during tempering. Both its high-temperature strength and room-temperature toughness are increased by decreasing its silicon content.The extraction residuals analysis, the TEM observation and the EDX analysis are performed on the quenched and quenched-tempered specimens. The effects of decreasing the silicon content of the tool steel are summarized as follows;A) The undissolved carbides (mainly MC type) are decreased at the quenching temperature, while these precipitates are increased after tempering.B) The grain boundary carbides (M23C6) are decreased after tempering.C) In the bainite structure, the silicon content does not affect the toughness, due to the precipitation of M2C type carbides. The high-temperature strength, however, is still dependent on the silicon content.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Umino, M., Sera, T., KONDO, K., Okada, Y., & Tubakino, H. (2003). Effect of Silicon Content on Tempered Hardness, High Temperature Strength and Toughness of Hot Working Tool Steels. 鐵と鋼 : 日本鐡鋼協會々誌, 89(6), 673–679. https://doi.org/10.2355/tetsutohagane1955.89.6_673

MLA 9

Umino, Masahide, et al. “Effect of Silicon Content on Tempered Hardness, High Temperature Strength and Toughness of Hot Working Tool Steels.” 鐵と鋼 : 日本鐡鋼協會々誌, vol. 89, no. 6, 2003, pp. 673–679. https://doi.org/10.2355/tetsutohagane1955.89.6_673.

Chicago

Umino, Masahide, Tomoaki Sera, Kunio KONDO, Yasutaka Okada, and Harushige Tubakino. 2003. “Effect of Silicon Content on Tempered Hardness, High Temperature Strength and Toughness of Hot Working Tool Steels.” 鐵と鋼 : 日本鐡鋼協會々誌 89 (6): 673–679. https://doi.org/10.2355/tetsutohagane1955.89.6_673.

Harvard

Umino, M. et al. (2003) ‘Effect of Silicon Content on Tempered Hardness, High Temperature Strength and Toughness of Hot Working Tool Steels’, 鐵と鋼 : 日本鐡鋼協會々誌, 89(6), pp. 673–679. doi:10.2355/tetsutohagane1955.89.6_673.

IEEE

M. Umino, T. Sera, K. KONDO, Y. Okada, and H. Tubakino, “Effect of Silicon Content on Tempered Hardness, High Temperature Strength and Toughness of Hot Working Tool Steels,” 鐵と鋼 : 日本鐡鋼協會々誌, vol. 89, no. 6, pp. 673–679, 2003, doi: 10.2355/tetsutohagane1955.89.6_673.

BibTeX

@article{umino2003effect,
  title     = {{Effect of Silicon Content on Tempered Hardness, High Temperature Strength and Toughness of Hot Working Tool Steels}},
  author    = {Umino, Masahide and Sera, Tomoaki and KONDO, Kunio and Okada, Yasutaka and Tubakino, Harushige},
  journal   = {鐵と鋼 : 日本鐡鋼協會々誌},
  year      = {2003},
  volume    = {89},
  number    = {6},
  pages     = {673--679},
  doi       = {10.2355/tetsutohagane1955.89.6_673},
  url       = {https://doi.org/10.2355/tetsutohagane1955.89.6_673}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
201211
201411
201511
202111
202333
202422

Topic and keywords

Physical Sciences › Materials Science › Metals and Alloys › Metal Alloys Wear and Properties

  • silicon content
  • hot work tool steel
  • high-temperature strength
  • toughness
  • secondary hardening
  • cementite precipitation
  • quenching cooling rate
  • undissolved carbides

Work with this paper

Most-cited papers in Materials Science

All highly cited Materials Science papers

Questions about this paper

How do I cite this paper in APA style?

Umino, M., Sera, T., KONDO, K., Okada, Y., & Tubakino, H. (2003). Effect of Silicon Content on Tempered Hardness, High Temperature Strength and Toughness of Hot Working Tool Steels. 鐵と鋼 : 日本鐡鋼協會々誌, 89(6), 673–679. https://doi.org/10.2355/tetsutohagane1955.89.6_673

How many times has this paper been cited?

14 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at 鐵と鋼 : 日本鐡鋼協會々誌: sign in and open the PDF from this page.

Who wrote this paper?

Masahide Umino, Tomoaki Sera, Kunio KONDO, Yasutaka Okada, Harushige Tubakino.

What is the DOI of this paper?

10.2355/tetsutohagane1955.89.6_673, permanently at https://doi.org/10.2355/tetsutohagane1955.89.6_673. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.