Journal article · 2026 · Open access

Effect of postpolymerization unit characteristics on the color stability and relative translucency parameter of 3D printed interim resins

Wanki Lee, Soyeon Kim, Alaa Daud, Jian Wang, Young‐Seok Park

Dental Materials · Published 1 October 2026 · DOI 10.1016/j.dental.2026.09.018

Open PDFView at the publisherCite this paper

In brief

“Effect of postpolymerization unit characteristics on the color stability and relative translucency parameter of 3D printed interim resins” is a 2026 journal article by Wanki Lee and 4 co-authors, published in Dental Materials. OpenAlex counts 0 citations as of 17 November 2026. It is open access under a CC BY-NC-ND licence: the full text is free to read at Dental Materials.

Citations
0
References
63
Authors
5

Abstract

Objectives This study evaluated the effects of postpolymerization unit characteristics on the color stability and relative translucency parameter of three-dimensional (3D) printed interim crown and bridge resins under simulated aging. Methods Four commercial resins were postpolymerized using five units. Spectral reflectance was measured before postpolymerization (T0), immediately afterward (T1), and after 6-month dry storage at 37 °C or 5000 thermocycles (T2). CIE L*a*b* (CIELAB) coordinates were calculated under CIE standard illuminant D65 using the CIE 1931 2° Standard Colorimetric Observer. The whiteness index for dentistry (WI D ) and CIEDE2000 color difference (ΔE 00 ) were derived from black-background coordinates, whereas the CIEDE2000 relative translucency parameter (RTP 00 ) was calculated from paired black- and white-background coordinates. Mean ΔL*, Δa*, and Δb* were evaluated using axis-specific visual thresholds, and T1-to-T2 ΔE 00 , |ΔWI D |, and |ΔRTP 00 | using perceptibility and acceptability thresholds. Results Postpolymerization generally reduced L* and WI D , whereas RTP 00 responses varied among resin–unit combinations. During dry storage, L* and WI D generally increased, whereas thermocycling generally decreased RTP 00 . Several outcomes differed significantly among postpolymerization units within each resin (p < 0.005). For Tera Harz TC-80DP, Tera Harz Cure and ODS Cure Box maintained ΔE 00 , |ΔWI D |, and |ΔRTP 00 | within acceptability thresholds under both aging conditions; with Tera Harz Cure, all three remained below perceptibility thresholds. Significance Color and RTP 00 stability depended on the specific resin–unit combination rather than manufacturer-designated pairing alone. Selected non-designated combinations showed acceptable in vitro outcomes. These findings support resin-specific selection based on verified performance of the complete postpolymerization protocol.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Lee, W., Kim, S., Daud, A., Wang, J., & Park, Y. (2026). Effect of postpolymerization unit characteristics on the color stability and relative translucency parameter of 3D printed interim resins. Dental Materials. https://doi.org/10.1016/j.dental.2026.09.018

MLA 9

Lee, Wanki, et al. “Effect of postpolymerization unit characteristics on the color stability and relative translucency parameter of 3D printed interim resins.” Dental Materials, 2026. https://doi.org/10.1016/j.dental.2026.09.018.

Chicago

Lee, Wanki, Soyeon Kim, Alaa Daud, Jian Wang, and Young‐Seok Park. 2026. “Effect of postpolymerization unit characteristics on the color stability and relative translucency parameter of 3D printed interim resins.” Dental Materials. https://doi.org/10.1016/j.dental.2026.09.018.

Harvard

Lee, W. et al. (2026) ‘Effect of postpolymerization unit characteristics on the color stability and relative translucency parameter of 3D printed interim resins’, Dental Materials. doi:10.1016/j.dental.2026.09.018.

IEEE

W. Lee, S. Kim, A. Daud, J. Wang, and Y. Park, “Effect of postpolymerization unit characteristics on the color stability and relative translucency parameter of 3D printed interim resins,” Dental Materials, 2026, doi: 10.1016/j.dental.2026.09.018.

BibTeX

@article{lee2026effect,
  title     = {{Effect of postpolymerization unit characteristics on the color stability and relative translucency parameter of 3D printed interim resins}},
  author    = {Lee, Wanki and Kim, Soyeon and Daud, Alaa and Wang, Jian and Park, Young‐Seok},
  journal   = {Dental Materials},
  year      = {2026},
  doi       = {10.1016/j.dental.2026.09.018},
  url       = {https://doi.org/10.1016/j.dental.2026.09.018}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Health Sciences › Dentistry › General Dentistry › Dental materials and restorations

  • color stability
  • artificial aging
  • thermal cycling
  • dry storage
  • whiteness index
  • CIEDE2000 color difference

Work with this paper

Most-cited papers in Dentistry

All highly cited Dentistry papers

Questions about this paper

How do I cite this paper in APA style?

Lee, W., Kim, S., Daud, A., Wang, J., & Park, Y. (2026). Effect of postpolymerization unit characteristics on the color stability and relative translucency parameter of 3D printed interim resins. Dental Materials. https://doi.org/10.1016/j.dental.2026.09.018

How many times has this paper been cited?

0 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Dental Materials: sign in and open the PDF from this page.

Who wrote this paper?

Wanki Lee, Soyeon Kim, Alaa Daud, Jian Wang, Young‐Seok Park.

What is the DOI of this paper?

10.1016/j.dental.2026.09.018, permanently at https://doi.org/10.1016/j.dental.2026.09.018. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.