Journal article · 2023 · Open access

Effect of MoO3 Content on Ni3Al-Ag-MoO3 Composite Coating Microstructure and Tribological Properties

Xiangjuan Fan, Wensheng Li, Jun Fen Yang, Shengyu Zhu, Shuai Cui, Bo Cheng, Haimin Zhai

Coatings, 13(3), 624 · Published 15 March 2023 · DOI 10.3390/coatings13030624

Open PDFView at the publisherCite this paper

In brief

“Effect of MoO3 Content on Ni3Al-Ag-MoO3 Composite Coating Microstructure and Tribological Properties” is a 2023 journal article by Xiangjuan Fan and 6 co-authors, published in Coatings. OpenAlex counts 9 citations as of 17 November 2026. It is open access under a CC BY licence: the full text is free to read at Coatings.

Citations
9
Most cited in
2025 (3)
Field-weighted impact
0.74
References
42
Authors
7

Abstract

In order to provide effective solid lubrication to Ni3Al coating, 10 wt.% Ag and different amounts of MoO3 solid lubricant were mechanically mixed with the SHSed Ni3Al powder and sprayed HVOF. Microstructure, mechanical properties, and tribological behavior from 25 °C to 800 °C of the coatings were studied, and the basic wear mechanisms were explored and discussed as well. Results show that the hardness and adhesive bonding strength of the coatings are slightly decreased, while there is little effect on the microstructure and mechanical properties of the Ni3Al-based composite coating when the content of MoO3 additive in the feedstock powder is lower than 15 wt.%. The composite coating formed by feedstock powder containing 15 wt.% MoO3 additive also presents excellent anti-friction and anti-wear performance from 25 °C to 800 °C, especially at 800 °C, where a complete, smooth, and thicker lubricating film comprised of NiO, Al2O3, MoO3, and Ag2MoO4 was formed, which reduced the friction coefficient (COF) and wear rate (WR) to the lowest value of 0.36 and 6.03 × 10−5 mm3/(Nm), respectively. An excessive amount of MoO3 in the feedstock powder (20 wt.%) results in inferior interlayer bonding of the formed coating, and the coating is more prone to delamination and abrasive wear above 200 °C.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Fan, X., Li, W., Yang, J. F., Zhu, S., Cui, S., Cheng, B., & Zhai, H. (2023). Effect of MoO3 Content on Ni3Al-Ag-MoO3 Composite Coating Microstructure and Tribological Properties. Coatings, 13(3), 624. https://doi.org/10.3390/coatings13030624

MLA 9

Fan, Xiangjuan, et al. “Effect of MoO3 Content on Ni3Al-Ag-MoO3 Composite Coating Microstructure and Tribological Properties.” Coatings, vol. 13, no. 3, 2023, p. 624. https://doi.org/10.3390/coatings13030624.

Chicago

Fan, Xiangjuan, Wensheng Li, Jun Fen Yang, Shengyu Zhu, Shuai Cui, Bo Cheng, and Haimin Zhai. 2023. “Effect of MoO3 Content on Ni3Al-Ag-MoO3 Composite Coating Microstructure and Tribological Properties.” Coatings 13 (3): 624. https://doi.org/10.3390/coatings13030624.

Harvard

Fan, X. et al. (2023) ‘Effect of MoO3 Content on Ni3Al-Ag-MoO3 Composite Coating Microstructure and Tribological Properties’, Coatings, 13(3), p. 624. doi:10.3390/coatings13030624.

IEEE

X. Fan et al., “Effect of MoO3 Content on Ni3Al-Ag-MoO3 Composite Coating Microstructure and Tribological Properties,” Coatings, vol. 13, no. 3, p. 624, 2023, doi: 10.3390/coatings13030624.

BibTeX

@article{fan2023effect,
  title     = {{Effect of MoO3 Content on Ni3Al-Ag-MoO3 Composite Coating Microstructure and Tribological Properties}},
  author    = {Fan, Xiangjuan and Li, Wensheng and Yang, Jun Fen and Zhu, Shengyu and Cui, Shuai and Cheng, Bo and Zhai, Haimin},
  journal   = {Coatings},
  year      = {2023},
  volume    = {13},
  number    = {3},
  pages     = {624},
  doi       = {10.3390/coatings13030624},
  url       = {https://doi.org/10.3390/coatings13030624}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
202311
202422
202533
202633

Its field-weighted citation impact is 0.74: it has been cited 0.74 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Materials Science › Surfaces, Coatings and Films › High-Temperature Coating Behaviors

  • silver
  • solid lubrication
  • composite coatings
  • high-temperature tribology
  • friction coefficient
  • wear rate
  • HVOF spraying
  • self-propagating high-temperature synthesis

Work with this paper

Most-cited papers in Materials Science

All highly cited Materials Science papers

Questions about this paper

How do I cite this paper in APA style?

Fan, X., Li, W., Yang, J. F., Zhu, S., Cui, S., Cheng, B., & Zhai, H. (2023). Effect of MoO3 Content on Ni3Al-Ag-MoO3 Composite Coating Microstructure and Tribological Properties. Coatings, 13(3), 624. https://doi.org/10.3390/coatings13030624

How many times has this paper been cited?

9 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Coatings: sign in and open the PDF from this page.

Who wrote this paper?

Xiangjuan Fan, Wensheng Li, Jun Fen Yang, Shengyu Zhu, Shuai Cui, Bo Cheng, Haimin Zhai.

What is the DOI of this paper?

10.3390/coatings13030624, permanently at https://doi.org/10.3390/coatings13030624. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.