Journal article · 2023 · Open access

Effect of HG40 and HS123 hard alloy tool substrates on the properties of hardening coating

В. С. Сергевнин, И. В. Блинков, Д. С. Белов, А. П. Демиров, А. В. Черногор, T. A. Lobova, А. I. Laptev

Powder Metallurgy аnd Functional Coatings, 17(3), 55–66 · Published 23 September 2023 · DOI 10.17073/1997-308x-2023-3-55-66

Open full textCite this paper

In brief

“Effect of HG40 and HS123 hard alloy tool substrates on the properties of hardening coating” is a 2023 journal article by В. С. Сергевнин and 6 co-authors, published in Powder Metallurgy аnd Functional Coatings. OpenAlex counts 1 citations as of 17 November 2026, which puts it in the top 9% of works published in 2023 by citations. It is open access under a CC BY-NC-ND licence: the full text is free to read at Powder Metallurgy аnd Functional Coatings.

Citations
1
Most cited in
2026 (1)
Field-weighted impact
0.10
References
40
Authors
7

Abstract

This article examines the impact of surface and near-surface layer properties of a hard alloy on the physico-mechanical and tribological properties of Mo–Ti–Ni–Si–Al–N CAPVD-coatings deposited on HG40 and HS123 cutting tools. In both cases, the coatings had similar composition, multilayer architecture, and nanograin structure, with crystallite sizes ranging from 6 to 10 nm. However, there were significant differences in the hardness, elasticity modulus, and relative work of plastic deformation between the coatings. Specifically, on HG40 substrates, the hardness, elasticity modulus, and relative work of plastic deformation were equal to 27.6 GPa, 647 GPa and 38.2 %, respectively, while on HS123 substrates, they were 34.2 GPa, 481 GPa and 46.2 %, respectively. Furthermore, coatings formed on HS123 hard alloy demonstrated superior wear resistance and stronger adhesion. This can be attributed to the presence of higher compressive macrostresses within the coating. The maximum value of this property, approximately 5.2 GPa, was achieved when deposed to HS123 hard alloy, whereas the coating applied to HG40 reached a maximum value of approximately 3.2 GPa. Additionally, a more extensive diffusion zone between the substrate and coating components, along with associated structural phase heterogeneity, was observed at the coating-substrate interface when applied to HS123 substrate.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Сергевнин, В. С., Блинков, И. В., Белов, Д. С., Демиров, А. П., Черногор, А. В., Lobova, T. A., & Laptev, А. I. (2023). Effect of HG40 and HS123 hard alloy tool substrates on the properties of hardening coating. Powder Metallurgy аnd Functional Coatings, 17(3), 55–66. https://doi.org/10.17073/1997-308x-2023-3-55-66

MLA 9

Сергевнин, В. С., et al. “Effect of HG40 and HS123 hard alloy tool substrates on the properties of hardening coating.” Powder Metallurgy аnd Functional Coatings, vol. 17, no. 3, 2023, pp. 55–66. https://doi.org/10.17073/1997-308x-2023-3-55-66.

Chicago

Сергевнин, В. С., И. В. Блинков, Д. С. Белов, А. П. Демиров, А. В. Черногор, T. A. Lobova, and А. I. Laptev. 2023. “Effect of HG40 and HS123 hard alloy tool substrates on the properties of hardening coating.” Powder Metallurgy аnd Functional Coatings 17 (3): 55–66. https://doi.org/10.17073/1997-308x-2023-3-55-66.

Harvard

Сергевнин, В. С. et al. (2023) ‘Effect of HG40 and HS123 hard alloy tool substrates on the properties of hardening coating’, Powder Metallurgy аnd Functional Coatings, 17(3), pp. 55–66. doi:10.17073/1997-308x-2023-3-55-66.

IEEE

В. С. Сергевнин et al., “Effect of HG40 and HS123 hard alloy tool substrates on the properties of hardening coating,” Powder Metallurgy аnd Functional Coatings, vol. 17, no. 3, pp. 55–66, 2023, doi: 10.17073/1997-308x-2023-3-55-66.

BibTeX

@article{2023effect,
  title     = {{Effect of HG40 and HS123 hard alloy tool substrates on the properties of hardening coating}},
  author    = {Сергевнин, В. С. and Блинков, И. В. and Белов, Д. С. and Демиров, А. П. and Черногор, А. В. and Lobova, T. A. and Laptev, А. I.},
  journal   = {Powder Metallurgy аnd Functional Coatings},
  year      = {2023},
  volume    = {17},
  number    = {3},
  pages     = {55--66},
  doi       = {10.17073/1997-308x-2023-3-55-66},
  url       = {https://doi.org/10.17073/1997-308x-2023-3-55-66}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Engineering › Mechanics of Materials › Metal and Thin Film Mechanics

  • tool coatings
  • coating-substrate interface
  • coating adhesion
  • wear resistance
  • hardness
  • elastic modulus
  • plastic deformation
  • diffusion zone

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Сергевнин, В. С., Блинков, И. В., Белов, Д. С., Демиров, А. П., Черногор, А. В., Lobova, T. A., & Laptev, А. I. (2023). Effect of HG40 and HS123 hard alloy tool substrates on the properties of hardening coating. Powder Metallurgy аnd Functional Coatings, 17(3), 55–66. https://doi.org/10.17073/1997-308x-2023-3-55-66

How many times has this paper been cited?

1 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Powder Metallurgy аnd Functional Coatings: sign in and open the full text from this page.

Who wrote this paper?

В. С. Сергевнин, И. В. Блинков, Д. С. Белов, А. П. Демиров, А. В. Черногор, T. A. Lobova, А. I. Laptev.

What is the DOI of this paper?

10.17073/1997-308x-2023-3-55-66, permanently at https://doi.org/10.17073/1997-308x-2023-3-55-66. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.