Journal article · 2017 · Open access

Effect of cutting speed on chip formation and wear mechanisms of coated carbide tools when ultra-high-speed face milling titanium alloy Ti-6Al-4V

Anhai Li, Jun Zhao, Guanming Hou

Advances in Mechanical Engineering, 9(7), 168781401771370 · Published 1 July 2017 · DOI 10.1177/1687814017713704

Open full textCite this paper

In brief

“Effect of cutting speed on chip formation and wear mechanisms of coated carbide tools when ultra-high-speed face milling titanium alloy Ti-6Al-4V” is a 2017 journal article by Anhai Li and 2 co-authors, published in Advances in Mechanical Engineering. OpenAlex counts 62 citations as of 17 November 2026, which puts it in the top 5% of works published in 2017 by citations. It is open access under a CC BY licence: the full text is free to read at Advances in Mechanical Engineering.

Citations
62
Most cited in
2025 (12)
Field-weighted impact
2.43
References
28
Authors
3

Abstract

Chip morphology and its formation mechanisms, cutting force, cutting power, specific cutting energy, tool wear, and tool wear mechanisms at different cutting speeds of 100–3000 m/min during dry face milling of Ti-6Al-4V alloy using physical vapor deposition-(Ti,Al)N-TiN-coated cemented carbide tools were investigated. The cutting speed was linked to the chip formation process and tool failure mechanisms of the coated cemented cutting tools. Results revealed that the machined chips exhibited clear saw-tooth profile and were almost segmented at high cutting speeds, and apparent degree of saw-tooth chip morphology occurred as cutting speed increased. Abrasion in the flank face, the adhered chips on the wear surface, and even melt chips were the most typical wear forms. Complex and synergistic interactions among abrasive wear, coating delamination, adhesive wear, oxidation wear, and thermal mechanical–mechanical impacts were the main wear or failure mechanisms. As the cutting speed was very high (>2000 m/min), discontinuous or fragment chips and even melt chips were produced, but few chips can be collected because the chips easily burned under the extremely high cutting temperature. Large area flaking, extreme abrasion, and serious adhesion dominated the wear patterns, and the tool wear mechanisms were the interaction of thermal wear and mechanical wear or failure under the ultra-high frequency and strong impact thermo-mechanical loads.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Li, A., Zhao, J., & Hou, G. (2017). Effect of cutting speed on chip formation and wear mechanisms of coated carbide tools when ultra-high-speed face milling titanium alloy Ti-6Al-4V. Advances in Mechanical Engineering, 9(7), 168781401771370. https://doi.org/10.1177/1687814017713704

MLA 9

Li, Anhai, et al. “Effect of cutting speed on chip formation and wear mechanisms of coated carbide tools when ultra-high-speed face milling titanium alloy Ti-6Al-4V.” Advances in Mechanical Engineering, vol. 9, no. 7, 2017, p. 168781401771370. https://doi.org/10.1177/1687814017713704.

Chicago

Li, Anhai, Jun Zhao, and Guanming Hou. 2017. “Effect of cutting speed on chip formation and wear mechanisms of coated carbide tools when ultra-high-speed face milling titanium alloy Ti-6Al-4V.” Advances in Mechanical Engineering 9 (7): 168781401771370. https://doi.org/10.1177/1687814017713704.

Harvard

Li, A., Zhao, J. and Hou, G. (2017) ‘Effect of cutting speed on chip formation and wear mechanisms of coated carbide tools when ultra-high-speed face milling titanium alloy Ti-6Al-4V’, Advances in Mechanical Engineering, 9(7), p. 168781401771370. doi:10.1177/1687814017713704.

IEEE

A. Li, J. Zhao, and G. Hou, “Effect of cutting speed on chip formation and wear mechanisms of coated carbide tools when ultra-high-speed face milling titanium alloy Ti-6Al-4V,” Advances in Mechanical Engineering, vol. 9, no. 7, p. 168781401771370, 2017, doi: 10.1177/1687814017713704.

BibTeX

@article{li2017effect,
  title     = {{Effect of cutting speed on chip formation and wear mechanisms of coated carbide tools when ultra-high-speed face milling titanium alloy Ti-6Al-4V}},
  author    = {Li, Anhai and Zhao, Jun and Hou, Guanming},
  journal   = {Advances in Mechanical Engineering},
  year      = {2017},
  volume    = {9},
  number    = {7},
  pages     = {168781401771370},
  doi       = {10.1177/1687814017713704},
  url       = {https://doi.org/10.1177/1687814017713704}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
201844
201933
202055
202177
20221010
202355
20241111
20251212
202655

Its field-weighted citation impact is 2.43: it has been cited 2.43 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization

  • cutting speed
  • chip formation
  • tool wear mechanisms
  • coated cemented carbide
  • Ti-6Al-4V
  • titanium alloys
  • face milling
  • dry machining

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Li, A., Zhao, J., & Hou, G. (2017). Effect of cutting speed on chip formation and wear mechanisms of coated carbide tools when ultra-high-speed face milling titanium alloy Ti-6Al-4V. Advances in Mechanical Engineering, 9(7), 168781401771370. https://doi.org/10.1177/1687814017713704

How many times has this paper been cited?

62 times, according to OpenAlex on 17 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Advances in Mechanical Engineering: sign in and open the full text from this page.

Who wrote this paper?

Anhai Li, Jun Zhao, Guanming Hou.

What is the DOI of this paper?

10.1177/1687814017713704, permanently at https://doi.org/10.1177/1687814017713704. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 17 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.