Journal article · 2016 · Open access

Diamond micro-milling of lithium niobate for sensing applications

Dehong Huo, Zi Jie Choong, Yilun Shi, John Hedley, Yan Hui Zhao

Journal of Micromechanics and Microengineering, 26(9), 095005 · Published 1 July 2016 · DOI 10.1088/0960-1317/26/9/095005

Open PDFView at the publisherCite this paper

In brief

“Diamond micro-milling of lithium niobate for sensing applications” is a 2016 journal article by Dehong Huo and 4 co-authors, published in Journal of Micromechanics and Microengineering. OpenAlex counts 37 citations as of 20 November 2026. It is open access under a CC BY licence: the full text is free to read at Journal of Micromechanics and Microengineering.

Citations
37
Most cited in
2018 (6)
Field-weighted impact
4.39
References
39
Authors
5

Abstract

Lithium niobate (LiNbO 3 ) is a crystalline material which is widely applied in surface acoustic wave, microelectromechanical systems (MEMS), and optical devices, owing to its superior physical, optical, and electronic properties. Due to its low toughness and chemical inactivity, LiNbO 3 is considered to be a hard-to-machine material and has been traditionally left as as an inert substrate upon which other micro structures are deposited. However, in order to make use of its superior material properties and increase efficiency, the fabrication of microstructures directly on LiNbO 3 is in high demand. This paper presents an experimental investigation on the micro machinability of LiNbO 3 via micro milling with the aim of obtaining optimal process parameters. Machining of micro slots was performed on Z -cut LiNbO 3 wafers using single crystal diamond tools. Surface and edge quality, cutting forces, and the crystallographic effect were examined and characterized. Ductile mode machining of LiNbO 3 was found to be feasible at a low feed rate and small depth of cut. A strong crystallographic effect on the machined surface quality was also observed. Finally, some LiNbO 3 micro components applicable to sensing applications were fabricated.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Huo, D., Choong, Z. J., Shi, Y., Hedley, J., & Zhao, Y. H. (2016). Diamond micro-milling of lithium niobate for sensing applications. Journal of Micromechanics and Microengineering, 26(9), 095005. https://doi.org/10.1088/0960-1317/26/9/095005

MLA 9

Huo, Dehong, et al. “Diamond micro-milling of lithium niobate for sensing applications.” Journal of Micromechanics and Microengineering, vol. 26, no. 9, 2016, p. 095005. https://doi.org/10.1088/0960-1317/26/9/095005.

Chicago

Huo, Dehong, Zi Jie Choong, Yilun Shi, John Hedley, and Yan Hui Zhao. 2016. “Diamond micro-milling of lithium niobate for sensing applications.” Journal of Micromechanics and Microengineering 26 (9): 095005. https://doi.org/10.1088/0960-1317/26/9/095005.

Harvard

Huo, D. et al. (2016) ‘Diamond micro-milling of lithium niobate for sensing applications’, Journal of Micromechanics and Microengineering, 26(9), p. 095005. doi:10.1088/0960-1317/26/9/095005.

IEEE

D. Huo, Z. J. Choong, Y. Shi, J. Hedley, and Y. H. Zhao, “Diamond micro-milling of lithium niobate for sensing applications,” Journal of Micromechanics and Microengineering, vol. 26, no. 9, p. 095005, 2016, doi: 10.1088/0960-1317/26/9/095005.

BibTeX

@article{huo2016diamond,
  title     = {{Diamond micro-milling of lithium niobate for sensing applications}},
  author    = {Huo, Dehong and Choong, Zi Jie and Shi, Yilun and Hedley, John and Zhao, Yan Hui},
  journal   = {Journal of Micromechanics and Microengineering},
  year      = {2016},
  volume    = {26},
  number    = {9},
  pages     = {095005},
  doi       = {10.1088/0960-1317/26/9/095005},
  url       = {https://doi.org/10.1088/0960-1317/26/9/095005}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
201755
201866
201944
202055
202122
202233
202333
202433
202533
202622

Its field-weighted citation impact is 4.39: it has been cited 4.39 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Advanced Surface Polishing Techniques

  • lithium niobate
  • single crystal diamond tool
  • micromachining
  • ductile machining
  • crystallographic effects
  • surface quality
  • cutting force
  • difficult-to-cut materials

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Huo, D., Choong, Z. J., Shi, Y., Hedley, J., & Zhao, Y. H. (2016). Diamond micro-milling of lithium niobate for sensing applications. Journal of Micromechanics and Microengineering, 26(9), 095005. https://doi.org/10.1088/0960-1317/26/9/095005

How many times has this paper been cited?

37 times, according to OpenAlex on 20 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Journal of Micromechanics and Microengineering: sign in and open the PDF from this page.

Who wrote this paper?

Dehong Huo, Zi Jie Choong, Yilun Shi, John Hedley, Yan Hui Zhao.

What is the DOI of this paper?

10.1088/0960-1317/26/9/095005, permanently at https://doi.org/10.1088/0960-1317/26/9/095005. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 20 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.