Journal article · 2024 · Open access

Designing a Robotic Gripper Based on the Actuating Capacity of NiTi-Based Shape Memory Wires

Adrian Petru Teodoriu, Bogdan Pricop, Nicoleta Monica Lohan, Mihai Popa, Radu-Ioachim Comăneci, Ioan Doroftei, Leandru-Gheorghe Bujoreanu

Actuators, 13(8), 319 · Published 21 August 2024 · DOI 10.3390/act13080319

Open PDFView at the publisherCite this paper

In brief

“Designing a Robotic Gripper Based on the Actuating Capacity of NiTi-Based Shape Memory Wires” is a 2024 journal article by Adrian Petru Teodoriu and 6 co-authors, published in Actuators. OpenAlex counts 6 citations as of 22 November 2026. It is open access under a CC BY licence: the full text is free to read at Actuators.

Citations
6
Most cited in
2026 (3)
Field-weighted impact
0.49
References
51
Authors
7

Abstract

In the present study, the capacity of two commercial NiTi and NiTiCu shape memory alloy (SMA) wires to develop work-generating (WG) and constrained-recovery (CR) shape memory effects (SMEs), as well as the capacity of a commercial NiTiFe super-elastic wire to act as cold-shape restoring element, have been investigated. Using differential scanning calorimetry (DSC), the reversible martensitic transformation to austenite of the three NiTi-based wires under study was emphasized by means of an endothermic minimum of the heat flow variation with temperature. NiTi and NiTiCu wire fragments were further tested for both WG-SME and CR-SME developed during the heating, from room temperature (RT) to different maximum temperatures selected from the DSC thermograms. The former tests revealed the capacity to repetitively lift various loads during repetitive heating, while the latter tests disclosed the repetitive development of shrinkage stresses during the repetitive heating of elongated wires. The tensile behavior of the three NiTi-based SMA wires was analyzed by failure and loading–unloading tests. The study disclosed the actuation capacity of NiTi and NiTiCu shape memory wires, which were able to develop work while being heated, as well as the resetting capacity of NiTiFe super-elastic wires, which can restore the initial undeformed shape of shape memory wires which soften while being cooled down. These features enable the design of a robotic gripper based on the development of NiTi-based actuators with repetitive action.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Teodoriu, A. P., Pricop, B., Lohan, N. M., Popa, M., Comăneci, R.-I., Doroftei, I., & Bujoreanu, L.-G. (2024). Designing a Robotic Gripper Based on the Actuating Capacity of NiTi-Based Shape Memory Wires. Actuators, 13(8), 319. https://doi.org/10.3390/act13080319

MLA 9

Teodoriu, Adrian Petru, et al. “Designing a Robotic Gripper Based on the Actuating Capacity of NiTi-Based Shape Memory Wires.” Actuators, vol. 13, no. 8, 2024, p. 319. https://doi.org/10.3390/act13080319.

Chicago

Teodoriu, Adrian Petru, Bogdan Pricop, Nicoleta Monica Lohan, Mihai Popa, Radu-Ioachim Comăneci, Ioan Doroftei, and Leandru-Gheorghe Bujoreanu. 2024. “Designing a Robotic Gripper Based on the Actuating Capacity of NiTi-Based Shape Memory Wires.” Actuators 13 (8): 319. https://doi.org/10.3390/act13080319.

Harvard

Teodoriu, A. P. et al. (2024) ‘Designing a Robotic Gripper Based on the Actuating Capacity of NiTi-Based Shape Memory Wires’, Actuators, 13(8), p. 319. doi:10.3390/act13080319.

IEEE

A. P. Teodoriu et al., “Designing a Robotic Gripper Based on the Actuating Capacity of NiTi-Based Shape Memory Wires,” Actuators, vol. 13, no. 8, p. 319, 2024, doi: 10.3390/act13080319.

BibTeX

@article{teodoriu2024designing,
  title     = {{Designing a Robotic Gripper Based on the Actuating Capacity of NiTi-Based Shape Memory Wires}},
  author    = {Teodoriu, Adrian Petru and Pricop, Bogdan and Lohan, Nicoleta Monica and Popa, Mihai and Comăneci, Radu-Ioachim and Doroftei, Ioan and Bujoreanu, Leandru-Gheorghe},
  journal   = {Actuators},
  year      = {2024},
  volume    = {13},
  number    = {8},
  pages     = {319},
  doi       = {10.3390/act13080319},
  url       = {https://doi.org/10.3390/act13080319}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Citations by year

YearCitationsShare of the best year
202422
202511
202633

Its field-weighted citation impact is 0.49: it has been cited 0.49 times as often as the average work of the same field, type and year (1.00 is the world average).

Topic and keywords

Physical Sciences › Materials Science › Materials Chemistry › Shape Memory Alloy Transformations

  • robotic gripper
  • shape memory alloy wires
  • NiTi
  • shape memory effect
  • constrained recovery
  • martensitic transformation
  • actuator design
  • tensile properties

Work with this paper

Most-cited papers in Materials Science

All highly cited Materials Science papers

Questions about this paper

How do I cite this paper in APA style?

Teodoriu, A. P., Pricop, B., Lohan, N. M., Popa, M., Comăneci, R.-I., Doroftei, I., & Bujoreanu, L.-G. (2024). Designing a Robotic Gripper Based on the Actuating Capacity of NiTi-Based Shape Memory Wires. Actuators, 13(8), 319. https://doi.org/10.3390/act13080319

How many times has this paper been cited?

6 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Actuators: sign in and open the PDF from this page.

Who wrote this paper?

Adrian Petru Teodoriu, Bogdan Pricop, Nicoleta Monica Lohan, Mihai Popa, Radu-Ioachim Comăneci, Ioan Doroftei, Leandru-Gheorghe Bujoreanu.

What is the DOI of this paper?

10.3390/act13080319, permanently at https://doi.org/10.3390/act13080319. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.