Journal article · 2026 · Open access

Design and Implementation of a Three-Segment Tendon-Driven Continuum Robot with Variable Stiffness for Manipulation in Confined Spaces

Zhixuan Weng, Liansen Sha, Yuehua Chen, Bingyu Fan, Lan Li, Bin Liu

Biomimetics, 11(2), 113 · Published 4 February 2026 · DOI 10.3390/biomimetics11020113

Open PDFView at the publisherCite this paper

In brief

“Design and Implementation of a Three-Segment Tendon-Driven Continuum Robot with Variable Stiffness for Manipulation in Confined Spaces” is a 2026 journal article by Zhixuan Weng and 5 co-authors, published in Biomimetics. OpenAlex counts 0 citations as of 22 November 2026. It is open access under a CC BY licence: the full text is free to read at Biomimetics.

Citations
0
References
38
Authors
6

Abstract

Continuum robots (CRs) exhibit high compliance and environmental adaptability in confined, tortuous spaces, yet their inherent low stiffness and load capacity limit performance in precise positioning and stable support tasks. To solve the "soft-rigid" paradox, this study proposes and implements a three-segment tendon-driven variable-stiffness CR. Structurally, a segmented constant-curvature model directs the optimization of grid skeletons and notch parameters, enhancing bending consistency and motion predictability. Elongated flat airbag actuators, arranged in annular arrays, enable segment-level stiffness switching through the enhancement of surface properties like axial constraints and friction amplification. A time-sharing drive strategy decouples multi-segment coupling into sequential single-segment subproblems, reducing drivers and kinematic complexity while maintaining dexterity. Experimental results demonstrate that flexible-mode joints maintain near-constant curvature with stable motion (average end-effector trajectory error < 0.9 mm), and in rigid mode, stiffness increases by a factor of 5.77 (rated load: 4.0 N). Shape-locking disturbances during transitions are confined to millimeter levels (remote offset < 1.32 mm), with successful traversal of J/U/S-shaped and irregular paths confirmed in pipeline tests. This work introduces a practical, scalable system for designing variable-stiffness structures and enabling low-complexity multi-segment control, offering valuable insights for minimally invasive devices and industrial endoscopy in confined spaces.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Weng, Z., Sha, L., Chen, Y., Fan, B., Li, L., & Liu, B. (2026). Design and Implementation of a Three-Segment Tendon-Driven Continuum Robot with Variable Stiffness for Manipulation in Confined Spaces. Biomimetics, 11(2), 113. https://doi.org/10.3390/biomimetics11020113

MLA 9

Weng, Zhixuan, et al. “Design and Implementation of a Three-Segment Tendon-Driven Continuum Robot with Variable Stiffness for Manipulation in Confined Spaces.” Biomimetics, vol. 11, no. 2, 2026, p. 113. https://doi.org/10.3390/biomimetics11020113.

Chicago

Weng, Zhixuan, Liansen Sha, Yuehua Chen, Bingyu Fan, Lan Li, and Bin Liu. 2026. “Design and Implementation of a Three-Segment Tendon-Driven Continuum Robot with Variable Stiffness for Manipulation in Confined Spaces.” Biomimetics 11 (2): 113. https://doi.org/10.3390/biomimetics11020113.

Harvard

Weng, Z. et al. (2026) ‘Design and Implementation of a Three-Segment Tendon-Driven Continuum Robot with Variable Stiffness for Manipulation in Confined Spaces’, Biomimetics, 11(2), p. 113. doi:10.3390/biomimetics11020113.

IEEE

Z. Weng, L. Sha, Y. Chen, B. Fan, L. Li, and B. Liu, “Design and Implementation of a Three-Segment Tendon-Driven Continuum Robot with Variable Stiffness for Manipulation in Confined Spaces,” Biomimetics, vol. 11, no. 2, p. 113, 2026, doi: 10.3390/biomimetics11020113.

BibTeX

@article{weng2026design,
  title     = {{Design and Implementation of a Three-Segment Tendon-Driven Continuum Robot with Variable Stiffness for Manipulation in Confined Spaces}},
  author    = {Weng, Zhixuan and Sha, Liansen and Chen, Yuehua and Fan, Bingyu and Li, Lan and Liu, Bin},
  journal   = {Biomimetics},
  year      = {2026},
  volume    = {11},
  number    = {2},
  pages     = {113},
  doi       = {10.3390/biomimetics11020113},
  url       = {https://doi.org/10.3390/biomimetics11020113}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Engineering › Biomedical Engineering › Soft Robotics and Applications

  • continuum robots
  • tendon-driven actuators
  • variable stiffness
  • confined space manipulation
  • constant curvature model
  • notch design
  • shape locking
  • minimally invasive devices

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Weng, Z., Sha, L., Chen, Y., Fan, B., Li, L., & Liu, B. (2026). Design and Implementation of a Three-Segment Tendon-Driven Continuum Robot with Variable Stiffness for Manipulation in Confined Spaces. Biomimetics, 11(2), 113. https://doi.org/10.3390/biomimetics11020113

How many times has this paper been cited?

0 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at Biomimetics: sign in and open the PDF from this page.

Who wrote this paper?

Zhixuan Weng, Liansen Sha, Yuehua Chen, Bingyu Fan, Lan Li, Bin Liu.

What is the DOI of this paper?

10.3390/biomimetics11020113, permanently at https://doi.org/10.3390/biomimetics11020113. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.