Conference paper · 2025 · Open access

Comparison of Mechanical Properties of 3D-printed PLA+ Lattice Infills at Different Build Orientation

Md. Jahid Hasan, Manish Bhadra Arnab, Moinul Hasan Sadik, Md. Abdul Hasib, Md. Ashraful Islam

SciEn Conference Series Engineering, 3, 540–544 · Published 11 November 2025 · DOI 10.38032/scse.2025.3.142

Open PDFView at the publisherCite this paper

In brief

“Comparison of Mechanical Properties of 3D-printed PLA+ Lattice Infills at Different Build Orientation” is a 2025 conference paper by Md. Jahid Hasan and 4 co-authors, published in SciEn Conference Series Engineering. OpenAlex counts 0 citations as of 22 November 2026. It is open access under a CC BY licence: the full text is free to read at SciEn Conference Series Engineering.

Citations
0
References
15
Authors
5

Abstract

Additive manufacturing (AM) can ensure the fabrication of complex structures as well as replace conventional parts for extensive modification and cheaper alternatives. Although the mechanical behaviors of different lattice structures have been studied extensively, the corresponding mechanical performances of integrated-manufactured structures with complex infills should be systematically investigated as the usage of 3D-printed parts replacing metals for strength applications can be seen more than ever. The main objective of this study was to investigate how printing factors like infill lattice structure and printing orientation affects the mechanical characteristics of printed samples. Samples were produced via an FDM 3D printer with similar conditions for each case. Kelvin and Octet lattice structures were compared on both horizontal and vertical printed orientations. The test was conducted on a specific geometry, 60mm cubic infill area with top and bottom wall and open sides. The comparison was done based on strength-to-weight characteristics of the samples with fixed weights for all cases. Compression tests using a universal testing machine (UTM) were done on the printed samples. The results of this study demonstrate that infill lattice structure and orientation significantly affect the compression strength of the PLA+ printed samples. The result shows that the lattice structure with unit cell of Octet lattice can withstand higher loads before failure, and the Kelvin lattice structure shows more ductile properties. It can also be seen that the horizontal printing orientation results in superior mechanical properties subjected to top loads than vertical orientation of printing. The research findings are helpful in understanding greater mechanical and physical characteristics that would undoubtedly assist designers and manufacturers worldwide as the FDM 3D printer becomes increasingly crucial in manufacturing engineering parts.

Cite this paper

Formatted from the catalogue record. Check names, capitals and page numbers against the paper before you submit.

APA 7

Hasan, M. J., Arnab, M. B., Sadik, M. H., Hasib, M. A., & Islam, M. A. (2025). Comparison of Mechanical Properties of 3D-printed PLA+ Lattice Infills at Different Build Orientation. SciEn Conference Series Engineering, 3, 540–544. https://doi.org/10.38032/scse.2025.3.142

MLA 9

Hasan, Md. Jahid, et al. “Comparison of Mechanical Properties of 3D-printed PLA+ Lattice Infills at Different Build Orientation.” SciEn Conference Series Engineering, vol. 3, 2025, pp. 540–544. https://doi.org/10.38032/scse.2025.3.142.

Chicago

Hasan, Md. Jahid, Manish Bhadra Arnab, Moinul Hasan Sadik, Md. Abdul Hasib, and Md. Ashraful Islam. 2025. “Comparison of Mechanical Properties of 3D-printed PLA+ Lattice Infills at Different Build Orientation.” SciEn Conference Series Engineering 3: 540–544. https://doi.org/10.38032/scse.2025.3.142.

Harvard

Hasan, M. J. et al. (2025) ‘Comparison of Mechanical Properties of 3D-printed PLA+ Lattice Infills at Different Build Orientation’, SciEn Conference Series Engineering, 3, pp. 540–544. doi:10.38032/scse.2025.3.142.

IEEE

M. J. Hasan, M. B. Arnab, M. H. Sadik, M. A. Hasib, and M. A. Islam, “Comparison of Mechanical Properties of 3D-printed PLA+ Lattice Infills at Different Build Orientation,” SciEn Conference Series Engineering, vol. 3, pp. 540–544, 2025, doi: 10.38032/scse.2025.3.142.

BibTeX

@inproceedings{hasan2025comparison,
  title     = {{Comparison of Mechanical Properties of 3D-printed PLA+ Lattice Infills at Different Build Orientation}},
  author    = {Hasan, Md. Jahid and Arnab, Manish Bhadra and Sadik, Moinul Hasan and Hasib, Md. Abdul and Islam, Md. Ashraful},
  booktitle = {SciEn Conference Series Engineering},
  year      = {2025},
  volume    = {3},
  pages     = {540--544},
  doi       = {10.38032/scse.2025.3.142},
  url       = {https://doi.org/10.38032/scse.2025.3.142}
}

Download for a reference manager: BibTeX (.bib) · RIS for Zotero, Mendeley and EndNote (.ris)

Topic and keywords

Physical Sciences › Engineering › Mechanical Engineering › Cellular and Composite Structures

  • 3D printing
  • fused deposition modeling
  • polylactic acid
  • build orientation
  • Kelvin lattice
  • octet lattice
  • compressive strength
  • specific strength

Work with this paper

Most-cited papers in Engineering

All highly cited Engineering papers

Questions about this paper

How do I cite this paper in APA style?

Hasan, M. J., Arnab, M. B., Sadik, M. H., Hasib, M. A., & Islam, M. A. (2025). Comparison of Mechanical Properties of 3D-printed PLA+ Lattice Infills at Different Build Orientation. SciEn Conference Series Engineering, 3, 540–544. https://doi.org/10.38032/scse.2025.3.142

How many times has this paper been cited?

0 times, according to OpenAlex on 22 November 2026. Google Scholar and Scopus count different sets of sources, so their numbers differ.

Is this paper free to read?

Yes. It is open access at SciEn Conference Series Engineering: sign in and open the PDF from this page.

Who wrote this paper?

Md. Jahid Hasan, Manish Bhadra Arnab, Moinul Hasan Sadik, Md. Abdul Hasib, Md. Ashraful Islam.

What is the DOI of this paper?

10.38032/scse.2025.3.142, permanently at https://doi.org/10.38032/scse.2025.3.142. Sign in and open it from this page.

Bibliographic data from OpenAlex (CC0), last checked 22 November 2026. ResearchGuru does not host this paper; once you are signed in, the links open it at the publisher or the repository that does.